Refine
Document Type
- Conference proceeding (41) (remove)
Is part of the Bibliography
- yes (41)
Institute
- Technik (41)
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
A fast transient current-mode buckboost DC-DC converter for portable devices is presented. Running at 1 MHz the converter provides stable 3 V from a 2.7 V to 4.2 V Li-Ion battery. A small voltage under-/overshoot is achieved by fast transient techniques: (1) adaptive pulse skipping (APS) and (2) adaptive compensation capacitance (ACC). The proposed converter was implemented in a 0.25 μm CMOS technology. Load transient simulations confirm the effectiveness of APS and ACC. The improvement in voltage undershoot and response time at light-to-heavy load step (100 mA to 500 mA), are 17 % and 59 %, respectively, in boost mode and 40 % and 49 %, respectively, in buck mode. Similar results are achieved at heavy-to-light load step for overshoot and response time.
A wide-bandwidth galvanically isolated current sensing circuit with an integrated Rogowski coil in 180nm CMOS is presented. Exploiting the high-frequency properties of an optimized on-chip Rogowski coil, currents can be measured up to a bandwidth of 75 MHz. The analog sensor front-end comprises a two-stage integrator, which allows a chopper frequency below signal bandwidth, resulting in 2.2 mVrms output noise. An additional integrated Hall sensor extends the measurement range towards DC.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
Die Spannungsversorgung elektronischer Steuergeräte im Automotive-Bereich wird zunehmend durch Schaltregler sichergestellt. Der SEPIC (Single Ended Primary Inductance Converter) besitzt die Eigenschaft, eine Spannung aufwärts wie auch abwärts wandeln zu können und könnte somit klassische Buck- und Boost-Wandler ablösen. Dieser Beitrag untersucht den SEPIC hinsichtlich Eignung für Automotive-Anwendungen. Dazu wurde eine Groß- sowie Kleinsignalanalyse am Wandler durchgeführt, mit geeigneten Simulationsmodellen nachgebildet und Messungen gegenüber gestellt. Der SEPIC zeigt als Hauptvorteile:
1. einen verzugsfreien Übergang zwischen Buck-/Boost Betrieb, 2. geringe Eingangswelligkeit, 3.DC-Kurzschlussfestigkeit. Auch hinsichtlich Wirkungsgrad und EMV-Verhalten stellt der SEPIC eine interessante Alternative dar. Der zwischen Ein- und Ausgang liegende Kondensator wird dauerhaft von einem Strom durchflossen, auf Basis der Effektivströme wird das damit verbundene Ausfallrisiko diskutiert.
In a digitally controlled slope shaping system, reliable detection of both voltage and current slope is required to enable a closed-loop control for various power switches independent of system parameters. In most state-of-the-art works, this is realized by monitoring the absolute voltage and current values. Better accuracy at lower DC power loss is achieved by sensing techniques for a reliable passive detection, which is achieved through avoiding DC paths from the high voltage network into the sensing network. Using a high-speed analog-to-digital converter, the whole waveform of the transient derivative can be stored digitally and prepared for a predictive cycle-by-cycle regulation, without requiring high-precision digital differentiation algorithms. To gain an accurate representation of the voltage and current derivative waveforms, system parasitics are investigated and classified in three sections: (1) component parasitics, which are identified by s-parameter measurements and extraction of equivalent circuit models, (2) PCB design issues related to the sensing circuit, and (3) interconnections between adjacent boards.
The contribution of this paper is an optimized sensing network on the basis of the experimental study supporting fast transition slopes up to 100 V/ns and 1 A/ns and beyond, making the sensing technique attractive for slope shaping of fast switching devices like modern generation IGBTs, CoolMOSTM and SiC mosfets. Measurements of the optimized dv/dt and di/dt setups are demonstrated for a hard switched IGBT power stage.
A concept for a slope shaping gate driver IC is proposed, used to establish control over the slew rates of current and voltage during the turn-on and turn off switching transients.
It combines the high speed and linearity of a fully-integrated closed-loop analog gate driver, which is able to perform real-time regulation, with the advantages of digital control, like flexibility and parameter independency, operating in a predictive cycle-bycycle regulation. In this work, the analog gate drive integrated circuit is partitioned into functional blocks and modeled in the small-signal domain, which also includes the non-linearity of parameters. An analytical stability analysis has been performed in order to ensure full functionality of the system controlling a modern generation IGBT and a superjunction MOSFET. Major parameters of influence, such as gate resistor and summing node capacitance, are investigated to achieve stable control. The large-signal behavior, investigated by simulations of a transistor level design, verifies the correct operation of the circuit. Hence, the gate driver can be designed for robust operation.
The increasing slew rate of modern power switches can increase the efficiency and reduce the size of power electronic applications. This requires a fast and robust signal transmission to the gate driver of the high-side switch. This work proposes a galvanically isolated capacitive signal transmission circuit to increase common mode transient immunity (CMTI). An additional signal path is introduced to significantly improve the transmission robustness for small duty cycles to assure a safe turn-off of the power switch. To limit the input voltage range at the comparator on the secondary side during fast high-side transitions, a clamping structure is implemented. A comparison between a conventional and the proposed signal transmission is performed using transistor level simulations. A propagation delay of about 2 ns over a wide range of voltage transients of up to 300V/ns at input voltages up to 600V is achieved.
Multilevel-cell (MLC) flash is commonly deployed in today’s high density NAND memories, but low latency and high reliability requirements make it barely used in automotive embedded flash applications. This paper presents a time domain voltage sensing scheme that applies a dynamic voltage ramp at the cells’ control gate (CG) in order to achieve fast and reliable sensing suitable for automotive applications.
DC-DC-converters are used in many different applications. Specifying the switching frequency is the most important parameter to calculate component costs and required space. Especially automotive applications of small brushed- or brushless dc-motors and the increasing number of DC-DC-converters have high requirements on the structual space (low box volume). This is of particular importance for automotive converters for the new 48 V board net. Multiplying the frequency by two will reduce the size of the power inductor by half at a given specification for output-voltage ripple. Smaller power inductors result in reduced losses due to smaller series resistance and parasitic capacitance. Furthermore a larger switching frequency decreases the size of the DC link capacitors. The circuit will get more idealized. However, as the switching losses increase with frequency, a DC-DC-converter can only benefit from these advantages if the switching behavior can be improved.
This paper presents an optimization method to increase switching slope and switching frequency of a 3.6 kW 3-phase step-up converter by separating the design and layout process into two parts. The first part is the power stage which carries the load current. It contains the power inductance and the drain-source-channel of the power MOSFETs. The second part is the driver circuit which contains the driver ICs, the gate resistor and the gate input impedance. While the switching slope was measured to be improved by 50 % , the switching time decreased by 20 %. Hence, the switching frequency of the step-up converter could be increased from 100 kHz to 200 kHz without loss increase. By mounting the driver ICs in a piggyback configuration in close proximity to the power stage, the parasitics could be further reduced significantly and 500 kHz switching frequency could be achieved with 97.5 % efficiency.
Die Nachfrage nach kompakten Spannungsversorgungen ist in den letzten Jahren stark gestiegen. Vor allem im Bereich der mobilen Geräte wachsen die Anforderung an die Spannungsversorgung hinsichtlich Bauvolumen und Batterielaufzeit. Für die Vollintegration von DC-DC- Wandlern als „Power Supply on Chip“ ist der SC-Wandler (Switched-Capacitor-Wandler) besonders geeignet. Insbesondere für Low-Power-Anwendungen im Bereich 10 mW kann ein SC-Wandler sehr gut, ohne externe Bauelemente, integriert werden. Während es für niedrige Eingangsspannungen (bis zu 5 V) eine Vielzahl an Topologien und Konzepten gibt, wurden SC-Wandler für höhere Eingangsspannungen (> 8 V) bisher nur wenig untersucht. Dieser Beitrag untersucht die wichtigsten Grundlagen für SC-Wandler mit Schwerpunkt auf hoher und zugleich variabler Eingangsspannung im Bereich 5 - 20 V. Am Beispiel eines Multi-Ratio-Wandlers (Wandler mit mehreren Übersetzungsverhältnissen), dem rekursiven SC-Wandler (RSC- Wandler), werden die Anforderungen eines SC- Wandler für hohe Eingangsspannungen herausgearbeitet und diskutiert.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
In recent years, significant progress has been made on switched-capacitor DC-DC converters as they enable fully integrated on-chip power management. New converter topologies overcame the fixed input-to-output voltage limitation and achieved high efficiency at high power densities. SC converters are attractive to not only mobile handheld devices with small input and output voltages, but also for power conversion in IoE, industrial and automotive applications, etc. Such applications need to be capable of handling widely varying input voltages of more than 10V, which requires a large amount of conversion ratios. The goal is to achieve a fine granularity with the least number of flying capacitors. In [1] an SC converter was introduced that achieves these goals at low input voltage VIN ≤ 2.5V. [2] shows good efficiency up to VIN = 8V while its conversion ratio is restricted to ≤1/2 with a limited, non-equidistant number of conversion steps. A particular challenge arises with increasing input voltage as several loss mechanisms like parasitic bottom-plate losses and gate-charge losses of high-voltage transistors become of significant influence. High input voltages require supporting circuits like level shifters, auxiliary supply rails etc., which allocate additional area and add losses [2-5]. The combination of both increasing voltage and conversion ratios (VCR) lowers the efficiency and the achievable output power of SC converters. [3] and [5] use external capacitors to enable higher output power, especially for higher VIN. However, this is contradictory to the goal of a fully integrated power supply.
In recent years, significant progress was made on switched-capacitor DCDC converters as they enable fully integrated on chip power management. New converter topologies overcame the fixed input-to-output voltage limitation and achieved high efficiency at high power densities. SC converters are attractive to not only mobile handheld devices with small input and output voltages, but also for power conversion in IoTs, industrial and automotive applications, etc. Such applications need to be capable of handling high input voltages of more than 10V. This talk highlights the challenges of the required supporting circuits and high voltage techniques, which arise for high Vin SC converters. It includes level shifters, charge pumps and back-to-back switches. High Vin conversion is demonstrated in a 4:1 SC DCDC converter with an input voltage as high as 17V with a peak efficiency of 45 %, and a buckboost SC converter with an input voltage range starting from 2 up to 13V, which utilizes a total of 17 ratios and achieves a peak efficiency of 81.5 %. Furthermore a highly integrated micro power supply approach is introduced, which is connected directly to the 120/230 Vrms mains, with an output power of 3mW, resulting in a power density >390μW/mm², which exceeds prior art by a factor of 11.
The level shifter and the floating gate supply for high-side transistors are a major challenge in high-voltage DCDC converters. This paper presents a high speed and power-efficient level shifter for voltages of up to 50V, suitable for both PMOS and NMOS power FETs. A switching node falling edge detection allows both, a sensitive and safe signal detection. This enables a robust operation during steep dv / dt transitions and a power consumption as low as 4.1 pJ per switching cycle, which is a reduction of more than 40% compared to prior art. An active clamping circuit prevents common mode displacement currents into the high-side supply. The level shifter is implemented in a 180nm BiCMOS technology. Measurements confirm a 50V 120MHz high-speed operation of the level shifter with a rising / falling propagation delay of 1.45 ns / 1.3 ns, respectively. The dv / dt robustness has been confirmed by measurements for transitions up to 6V/ ns.
Size and cost of a boost converter can be minimized by reducing the voltage overshoot and fastening the transient response in case of load transient. The presented technique improves the transient response of a current mode controlled boost converter, which usually suffers from bandwidth limitation because of its right-half-plane zero (RHPZ). The proposed technique comprises a load current estimation which works as part of a digital controller without any additional measurements. Based on the latest load estimation the controller parameters are adapted, achieving small voltage overshoot and fast transient response. The presented technique was implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology, a Xilinx Spartan-6 field programmable gate array (FPGA), and a TI-ADS8422 analog to-digital-converter (ADC). Simulation and measurements of a 4V-to-6.3V, 500mA boost converter show an improvement of 50% in voltage overshoot and response time to load transient.
Boost converters suffer from a bandwidth limitation caused by the right-half plane zero (RHPZ), which occurs in the control-to-output transfer function. In contrast, there are many applications that require superior dynamic behavior. Further, size and cost of boost converter systems can be minimized by reduced voltage deviations and fast transient responses in case of large signal load transients. The key idea of the proposed ΔV/Δt-intervention control concept is to adapt the controller output to its new steady state value immediately after a load transient by prediction from known parameters. The concept is implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology and a Xilinx Spartan-6 field programmable gate array (FPGA). In a boost converter with 3.5V input voltage, 6.3V output voltage, 1.2A load, and 500 kHz switching frequency, the output voltage deviations are 2.8x smaller, scaling down the output capacitor value by the same factor. The recovery times are 2.4x shorter in case of large signal load transients with the proposed concept. The control is widely applicable, as it supports constant switching frequencies and allows for duty cycle and inductor current limitations. It also shows various advantages compared to conventional control and to selected adaptive control concepts.
This paper presents a digitally controlled boost converter IC for high output voltage and fast transient applications. Thus, it is well applicable in automotive and industrial environments. The 3V-to-6V input voltage, 6.3V output voltage, 1A boost converter IC is fabricated in a 180nm BCD technology. Digital control enables cost savings, advanced control concepts, and it is less parameter sensitive compared to common analog control. A 90 ns latency, 6-bit delay line ADC operates with a window concept, meeting high resolution requirements, e.g. in car battery applications. An output voltage live tracking is included for extending the ADC conversion window. A charge pump DAC provides high resolution, monotonicity, and short 128 ns conversion time. Further, a standard digital PI controller is enhanced by a simple but effective ΔV/Δt-intervention control. It results in 2.8x reduced output voltage deviations in case of load steps, scaling down the output capacitor value by the same factor.
A high-voltage replica based current sensor is presented, along with challenges and design techniques which are rarely discussed in literature so far. The performance is evaluated by detailed small signal and large signal analysis. By dedicated placing of high-voltage cascode devices, while keeping as many low-voltage devices as possible, a high gain-bandwidth product is achieved. A decoupling and biasing circuit is introduced which improves the response time of the current sensor at on/off transitions by a factor of five. The current sensor is implemented in a 180nm HV BiCMOS technology. The sensor achieves a DC loop gain of 83 dB and a gain-bandwidth product of 7 MHz. With the proposed techniques, the gain-bandwidth product is increased by a factor of six. The measurable current range is between 60mA and 1.5 A. The performance is demonstrated in a 500 kHz buck converter at an input voltage of 40V. The overall circuit concept is suitable for 100V and beyond, enabling high performance power management designs including switched mode power supplies and motor applications.