Refine
Document Type
- Conference proceeding (222)
- Journal article (28)
Language
- English (250)
Is part of the Bibliography
- yes (250)
Institute
- Technik (140)
- Informatik (89)
- ESB Business School (19)
- Life Sciences (1)
- Texoversum (1)
Publisher
- IEEE (250) (remove)
Modern power transistors are able to switch at very high transition speed, which can cause EMC violations and overshoot. This is addressed by a gate driver with variable gate current, which is able to control the transition speed. The key idea is that the gate driver can influence the di/dt and dv/dt transition separately and optimize whichever transition promises the highest improvement while keeping switching losses low. To account for changes in the load current, supply voltage, etc., a control loop is required in the driver to ensure optimized switching. In this paper, an efficient control scheme for an automotive gate driver with variable output current capability is presented. The effectiveness of the control loop is demonstrated for a MOSFET bridge consisting of OptiMOS-T2™devices with a total gate charge of 39nC. This bridge setup shows dv/dt transitions between 50 to 1000ns, depending on driving current. The driver is able to switch between gate current levels of 1 to 500mA in 10/15ns (rising/falling transition). With the implemented control loop the driver is measured to significantly reduce the ringing and thereby reduce device stress and electromagnetic emissions while keeping switching losses 52% lower than with a constant current driver.
More and more power electronics applications utilize GaN transistors as they enable higher switching frequencies in comparison to conventional Si devices. Faster switching shrinks down the size of passives and enables compact solutions in applications like renewable energy, electrical cars and home appliances. GaN transistors benefit from ~10× smaller gate charge QG and gate drive voltages in the range of typically 5V vs. ~15V for Si.
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
In recent years, significant progress has been made on switched-capacitor DC-DC converters as they enable fully integrated on-chip power management. New converter topologies overcame the fixed input-to-output voltage limitation and achieved high efficiency at high power densities. SC converters are attractive to not only mobile handheld devices with small input and output voltages, but also for power conversion in IoE, industrial and automotive applications, etc. Such applications need to be capable of handling widely varying input voltages of more than 10V, which requires a large amount of conversion ratios. The goal is to achieve a fine granularity with the least number of flying capacitors. In [1] an SC converter was introduced that achieves these goals at low input voltage VIN ≤ 2.5V. [2] shows good efficiency up to VIN = 8V while its conversion ratio is restricted to ≤1/2 with a limited, non-equidistant number of conversion steps. A particular challenge arises with increasing input voltage as several loss mechanisms like parasitic bottom-plate losses and gate-charge losses of high-voltage transistors become of significant influence. High input voltages require supporting circuits like level shifters, auxiliary supply rails etc., which allocate additional area and add losses [2-5]. The combination of both increasing voltage and conversion ratios (VCR) lowers the efficiency and the achievable output power of SC converters. [3] and [5] use external capacitors to enable higher output power, especially for higher VIN. However, this is contradictory to the goal of a fully integrated power supply.
The presented wide-Vin step-down converter introduces a parallel-resonant converter (PRC), comprising an integrated 5-bit capacitor array and a 300 nH resonant coil, placed in parallel to a conventional buck converter. Unlike conventional resonant concepts, the implemented soft-switching control eliminates input voltage dependent losses over a wide operating range. This ensures high efficiency across a wide range of Vin= 12-48V, 100-500mA load and 5V output at up to 15MHz switching frequency. The peak efficiency of the converter is 76.3 %. Thanks to the low output current ripple, the output capacitor can be as small as 50 nF, while the inductor tolerates a larger ESR, resulting in small component size. The proposed PRC architecture is also suitable for future power electronics applications using fast-switching GaN devices.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
A high-voltage replica based current sensor is presented, along with challenges and design techniques which are rarely discussed in literature so far. The performance is evaluated by detailed small signal and large signal analysis. By dedicated placing of high-voltage cascode devices, while keeping as many low-voltage devices as possible, a high gain-bandwidth product is achieved. A decoupling and biasing circuit is introduced which improves the response time of the current sensor at on/off transitions by a factor of five. The current sensor is implemented in a 180nm HV BiCMOS technology. The sensor achieves a DC loop gain of 83 dB and a gain-bandwidth product of 7 MHz. With the proposed techniques, the gain-bandwidth product is increased by a factor of six. The measurable current range is between 60mA and 1.5 A. The performance is demonstrated in a 500 kHz buck converter at an input voltage of 40V. The overall circuit concept is suitable for 100V and beyond, enabling high performance power management designs including switched mode power supplies and motor applications.
This paper presents a wide-Vin step-down parallel-resonant converter (PRC), comprising an integrated 5-bit capacitor array and a 300-nH resonant coil, placed in parallel to a conventional buck converter. Soft-switching resonant converters are beneficial for high-Vin multi-MHz converters to reduce dominant switching losses, enabling higher switching frequencies. The output filter inductor is optimized based on an empirical study of available inductors. The study shows that faster switching significantly reduces not only the inductor value but also volume, price, and even the inductor losses. In addition, unlike conventional resonant concepts, soft-switching control as part of the proposed PRC eliminates input voltage-dependent losses over a wide operating range, resulting in 76.3% peak efficiency. At Vin = 48 V, a loss reduction of 35% is achieved compared with the conventional buck converter. Adjusting an integrated capacitor array, and selecting the number of oscillation periods, keeps the switching frequency within a narrow range. This ensures high efficiency across a wide range of Vin = 12–48 V, 100–500-mA load, and 5-V output at up to 25-MHz switching frequency. Thanks to the low output current ripple, the output capacitor can be as small
as 50 nF.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
The level shifter and the floating gate supply for high-side transistors are a major challenge in high-voltage DCDC converters. This paper presents a high speed and power-efficient level shifter for voltages of up to 50V, suitable for both PMOS and NMOS power FETs. A switching node falling edge detection allows both, a sensitive and safe signal detection. This enables a robust operation during steep dv / dt transitions and a power consumption as low as 4.1 pJ per switching cycle, which is a reduction of more than 40% compared to prior art. An active clamping circuit prevents common mode displacement currents into the high-side supply. The level shifter is implemented in a 180nm BiCMOS technology. Measurements confirm a 50V 120MHz high-speed operation of the level shifter with a rising / falling propagation delay of 1.45 ns / 1.3 ns, respectively. The dv / dt robustness has been confirmed by measurements for transitions up to 6V/ ns.
This paper presents a digitally controlled boost converter IC for high output voltage and fast transient applications. Thus, it is well applicable in automotive and industrial environments. The 3V-to-6V input voltage, 6.3V output voltage, 1A boost converter IC is fabricated in a 180nm BCD technology. Digital control enables cost savings, advanced control concepts, and it is less parameter sensitive compared to common analog control. A 90 ns latency, 6-bit delay line ADC operates with a window concept, meeting high resolution requirements, e.g. in car battery applications. An output voltage live tracking is included for extending the ADC conversion window. A charge pump DAC provides high resolution, monotonicity, and short 128 ns conversion time. Further, a standard digital PI controller is enhanced by a simple but effective ΔV/Δt-intervention control. It results in 2.8x reduced output voltage deviations in case of load steps, scaling down the output capacitor value by the same factor.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum conversion ratio are limited by the duty cycle of a PWM signal. In DCDC converters, a sawtooth generator is the fundamental circuit block to generate the PWM signal. The presented PWM generator is based on two parallel, fully interleaved PWM generator stages, each containing an integrator based sawtooth generator and two 3-stage highspeed comparators. A digital multiplexing of the PWM signals of each stage eliminates the dependency of the minimum on-time on the large reset times of the sawtooth ramps. A separation of the references of the PWM comparators in both stage allows to configure the PWM generator for a DCDC converter operating in fixed frequency or in constant on-time mode, which requires an operation in a wide frequency range. The PWM generator was fabricated in an 180 nm HV BiCMOS technology, as part of a DCDC converter. Measurements confirm minimum possible ontime pulses as short as 2 ns and thus allows switching frequencies of DCDC converters of >50 MHz at small duty cycle of <10%. At moderate duty cycles switching frequencies up to 100 MHz are possible.
The increasing share of renewable energy with volatile production results in higher variability of prices for electrical energy. Optimized operating schedules, e.g., for industrial units, can yield a considerable reduction of energy costs by shifting processes with high power consumption to times with low energy prices. We present a distributed control architecture for virtual power plants (VPPs) where VPP participants benefit from flexible adaptation of schedules to price forecasts while maintaining control of their operating schedule. An aggregator trades at the energy market on behalf of the participants and benefits from more detailed and reliable load profiles within the VPP.
We present a dual active bridge topology suitable for wide voltage range applications covering all combinations of 200V to 600V on the input and 20V to 60V on the output with constant power of 1kW.We employ a stepped inductance scheme to adjust the effective inductance of the converter, thus extending the efficient operation range. Using a variable switching frequency between 35 kHz and 150 kHz with operation-point-dependent limits further increases the performance of the converter. A prototype was built and the proposed changes have been compared to a fixed frequency, fixed inductance implementation. Measurements show a maximum loss reduction of 40 %, leading to a peak efficiency of 97% while maintaining constant output power over the entire working area.
A wide-bandwidth galvanically isolated current sensing circuit with an integrated Rogowski coil in 180nm CMOS is presented. Exploiting the high-frequency properties of an optimized on-chip Rogowski coil, currents can be measured up to a bandwidth of 75 MHz. The analog sensor front-end comprises a two-stage integrator, which allows a chopper frequency below signal bandwidth, resulting in 2.2 mVrms output noise. An additional integrated Hall sensor extends the measurement range towards DC.
Due to their superior fast-switching performance, GaN transistors show enormous potential to enable compact power electronics in applications like renewable energy, electrical cars and home appliances by shrinking down the size of passives. However, fast switching poses challenges for the gate driver. Since GaN transistors have a low threshold voltage Vt of ~1V, an unintended driver turn-on can occur in case of a unipolar gate control as shown for a typical half-bridge in Fig. 24.2.1 (top left). This is due to coupling via the gate-drain capacitance (Miller coupling), when the low-side driver turns on, causing a peak current into the gate. This is usually tackled by applying a negative gate voltage to enhance the safety margin towards Vt, resulting in a bipolar gate-driving scheme. In many power-electronics applications GaN transistors operate in reverse conduction, carrying the inductor current during the dead time t, when the high-side and low-side switch are off (as illustrated at a high-side switch in Fig. 24.2.1, bottom left). As there is no real body diode as in silicon devices, the GaN transistor turns on in reverse operation with a voltage drop VF across the drain-source terminals (quasi-body diode behavior). As a negative gate voltage adds to VF, 63% higher reverse-conduction losses were measured for a typical GaN switch in bipolar gate-drive operation. This drawback is addressed by a three-level gate voltage (positive, 0V, negative), which at the same time provides robustness against unintended turn-on similar to the bipolar gate driver, proven in [1] for a discrete driver.
A fully passive RFID temperature sensor SoC with an accuracy of ±0.4 ◦C (3σ) from 0 ◦C to 125 ◦C
(2019)
This paper presents a fully passive 13.56 -MHz RFID temperature sensor system-on-chip. Its power management unit operates over a large temperature range using a zero temperature coefficient bias source. On-chip temperature sensing is accomplished with low-voltage, low-power CMOS circuitry, and time-domain signal processing. Two readout commands have been defined to study supply noise sensitivity: 1) standard readout, where just a single set of data is transferred to the reader and 2) serial readout, where several sets of data are sent one after the other to the reader. With the standard readout command, the sensor suffers from interference from the RFID command packet and outputs interference as well, while the sensor outputs no interference with the serial readout command. Measurements show that sensor resolution with serial readout is improved by a factor of approximately 16 compared to standard readout. The chip was fabricated in a standard 0.35-μm CMOS technology and chip-on-board mounted to a tuned RFID transponder coil on an aluminum core FR4 PCB substrate. Real time wireless temperature sensing has been demonstrated with a commercial HF RFID reader. With a two-point calibration, the SoC achieves a 3σ sensing accuracy of ±0.4 ◦C from 0◦C to 125 ◦C.