Refine
Document Type
- Conference proceeding (41)
- Patent / Standard / Guidelines (11)
- Journal article (9)
- Book chapter (1)
Is part of the Bibliography
- yes (62)
Institute
- Technik (62)
Publisher
- IEEE (31)
- Hochschule Ulm (6)
- Technische Universität Berlin (3)
- Technische Universität Darmstadt (2)
- Arbeitsgemeinschaft Simulation (ASIM) (1)
- Copernicus GmbH (1)
- ECPE (1)
- International Union of Radio Science / Landesausschuss in der Bundesrepublik Deutschland (1)
- Power Sources Manufacturers Association (1)
- Springer (1)
Die Spannungsversorgung elektronischer Steuergeräte im Automotive-Bereich wird zunehmend durch Schaltregler sichergestellt. Der SEPIC (Single Ended Primary Inductance Converter) besitzt die Eigenschaft, eine Spannung aufwärts wie auch abwärts wandeln zu können und könnte somit klassische Buck- und Boost-Wandler ablösen. Dieser Beitrag untersucht den SEPIC hinsichtlich Eignung für Automotive-Anwendungen. Dazu wurde eine Groß- sowie Kleinsignalanalyse am Wandler durchgeführt, mit geeigneten Simulationsmodellen nachgebildet und Messungen gegenüber gestellt. Der SEPIC zeigt als Hauptvorteile:
1. einen verzugsfreien Übergang zwischen Buck-/Boost Betrieb, 2. geringe Eingangswelligkeit, 3.DC-Kurzschlussfestigkeit. Auch hinsichtlich Wirkungsgrad und EMV-Verhalten stellt der SEPIC eine interessante Alternative dar. Der zwischen Ein- und Ausgang liegende Kondensator wird dauerhaft von einem Strom durchflossen, auf Basis der Effektivströme wird das damit verbundene Ausfallrisiko diskutiert.
A fast transient current-mode buckboost DC-DC converter for portable devices is presented. Running at 1 MHz the converter provides stable 3 V from a 2.7 V to 4.2 V Li-Ion battery. A small voltage under-/overshoot is achieved by fast transient techniques: (1) adaptive pulse skipping (APS) and (2) adaptive compensation capacitance (ACC). The proposed converter was implemented in a 0.25 μm CMOS technology. Load transient simulations confirm the effectiveness of APS and ACC. The improvement in voltage undershoot and response time at light-to-heavy load step (100 mA to 500 mA), are 17 % and 59 %, respectively, in boost mode and 40 % and 49 %, respectively, in buck mode. Similar results are achieved at heavy-to-light load step for overshoot and response time.
Bootstrap circuits are mainly used for supplying a gate driver circuit to provide the gate overdrive voltage for a high-side NMOS transistor. The required charge has to be provided by a bootstrap capacitor which is often too large for integration if an acceptable voltage dip at the capacitor has to be guaranteed. Three options of an area efficient bootstrap circuit for a high side driver with an output stage of two NMOS transistors are proposed. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and connected when the gate driver turns on. A high voltage swing at the second capacitor leads to a high charge allocation. Both bootstrap capacitors require up to 70% less area compared to a conventional bootstrap circuit. This enables compact power management systems with fewer discrete components and smaller die size. A calculation guideline for optimum bootstrap capacitor sizing is given. The circuit was manufactured in a 180nm high-voltage BiCMOS technology as part of a high-voltage gate driver. Measurements confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit including two stacked 75.8pF and 18.9pF capacitors results in a voltage dip lower than 1V. This matches well with the theory of the calculation guideline.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. This leads especially at a high input voltage to a decreasing efficiency caused by switching losses. Conventional calculations are not suitable to predict the efficiency as parasitic capacitances have a significant loss contribution. This paper presents an analytical efficiency model which considers parasitic capacitances separately and calculates the power loss contribution of each capacitance to any resistive element. The proposed model is utilized for efficiency optimization of converters with switching frequencies >10MHz and input voltages up to 40V. For experimental evaluation a DCDC converter was manufactured in a 180 nm HV BiCMOS technology. The model matches a transistor level simulation and measurement results with an accuracy better than 3.5 %. The accuracy of the parasitic capacitances of the high voltage transistor determines the overall accuracy of the efficiency model. Experimental capacitor measurements can be fed into the model. Based on the model, different architectures have been studied.
Durch schnell schaltende Leistungsendstufen werden durch kapazitive Umladeströme Störungen ins Substrat und in empfindliche Schaltungselemente eingekoppelt, die dort zur Störung der Funktion führen können. In dieser Arbeit werden Substratstrukturen zur gezielten Ableitung dieser Störungen vorgestellt und ihre Wirksamkeit mit Hilfe von Device Simulation evaluiert. Ohne Ableitstrukturen kann eine Potentialanhebung des Substrats bis zu 20 V entstehen. Die Untersuchungen belegen, dass die Potentialanhebung durch p-Typ Guard-Ringe um 75 %, durch leitende Trenches um 88 % sowie durch Rückseitenmetallisierung um nahezu 100 % reduziert werden kann.
A millimeter-wave power amplifier concept in an advanced silicon germanium (SiGe) BiCMOS technology is presented. The goal of the concept is to investigate the impact of physical limitations of the used heterojunction bipolar transistors (HBT) on the performance of a 77 GHz power amplifier. High current behavior, collectorbase breakdown and transistor saturation can be forced with the presented design. The power amplifier is manufactured in an advanced SiGe BiCMOS technology at Infineon Technologies AG with a maximum transit frequency fT of around 250 GHz for npn HBT’s [1]. The simulation results of the power amplifier show a saturated output power of 16 dBm at a power added efficiency of 13%. The test chip is designed for a supply voltage of 3.3 V and requires a chip size of 1.448 x 0.930 mm².
For area reasons, NMOS transistors are preferred over PMOS for the pull-up path in gate drivers. Bootstrapping has to ensure sufficient NMOS gate overdrive. Especially in high-current gate drivers with large transistors, the bootstrap capacitor is too large for integration. This paper proposes three options of fully integrated bootstrap circuits. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and ensures high charge allocation when the driver turns on. A capacitor sizing guideline and the overall driver implementation including a suitable charge pump for permanent driver activation is provided. A linear regulator is used for bootstrap supply and it also compensates the voltage drop of the bootstrap diode. Measurements from a testchip in 180 nm high-voltage BiCMOS confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit with two stacked 75.8 pF and 18.9 pF capacitors results in an expected voltage dip of lower than 1 V. Both bootstrap capacitors require 70% less area compared to a conventional bootstrap circuit. Besides drivers, the proposed bootstrap can also be directly applied to power stages to achieve fully integrated switched mode power supplies or class-D output stages.
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum conversion ratio are limited by the duty cycle of a PWM signal. In DCDC converters, a sawtooth generator is the fundamental circuit block to generate the PWM signal. The presented PWM generator is based on two parallel, fully interleaved PWM generator stages, each containing an integrator based sawtooth generator and two 3-stage highspeed comparators. A digital multiplexing of the PWM signals of each stage eliminates the dependency of the minimum on-time on the large reset times of the sawtooth ramps. A separation of the references of the PWM comparators in both stage allows to configure the PWM generator for a DCDC converter operating in fixed frequency or in constant on-time mode, which requires an operation in a wide frequency range. The PWM generator was fabricated in an 180 nm HV BiCMOS technology, as part of a DCDC converter. Measurements confirm minimum possible ontime pulses as short as 2 ns and thus allows switching frequencies of DCDC converters of >50 MHz at small duty cycle of <10%. At moderate duty cycles switching frequencies up to 100 MHz are possible.
Substrate coupling is a critical failure mechanism especially in fast-switching integrated power stages controlling high-side NMOS power FETs. The parasitic coupling across the substrate in integrated power stages at rise times of up to 500 ps and input voltages of up to 40V is investigated in this paper. The coupling has been studied for the power stage of an integrated buck converter. In particular, dedicated diverting and isolation structures against substrate coupling are analyzed by simulations and evaluated with measurements from test chips in 180nm high-voltage BiCMOS. The results are compared regarding effectiveness, area as well as implementation effort and cost. Back-side metalization shows superior characteristics with nearly 100% noise suppression. Readily available p-guard ring structures bring 75% disturbance reduction. The results are applicable to advanced and future power management solutions with fully integrated switched-mode power supplies at switching frequencies >10 MHz.
DC-DC-converters are used in many different applications. Specifying the switching frequency is the most important parameter to calculate component costs and required space. Especially automotive applications of small brushed- or brushless dc-motors and the increasing number of DC-DC-converters have high requirements on the structual space (low box volume). This is of particular importance for automotive converters for the new 48 V board net. Multiplying the frequency by two will reduce the size of the power inductor by half at a given specification for output-voltage ripple. Smaller power inductors result in reduced losses due to smaller series resistance and parasitic capacitance. Furthermore a larger switching frequency decreases the size of the DC link capacitors. The circuit will get more idealized. However, as the switching losses increase with frequency, a DC-DC-converter can only benefit from these advantages if the switching behavior can be improved.
This paper presents an optimization method to increase switching slope and switching frequency of a 3.6 kW 3-phase step-up converter by separating the design and layout process into two parts. The first part is the power stage which carries the load current. It contains the power inductance and the drain-source-channel of the power MOSFETs. The second part is the driver circuit which contains the driver ICs, the gate resistor and the gate input impedance. While the switching slope was measured to be improved by 50 % , the switching time decreased by 20 %. Hence, the switching frequency of the step-up converter could be increased from 100 kHz to 200 kHz without loss increase. By mounting the driver ICs in a piggyback configuration in close proximity to the power stage, the parasitics could be further reduced significantly and 500 kHz switching frequency could be achieved with 97.5 % efficiency.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
There is a growing need for motor drives with improved EMC in various automotive and industrial applications. An often referenced approach to reduce EME is to change the shape of the switching signal to reduce the EMI caused by the voltage and current transitions. This requires very precise gate control of the power MOSFET to achive better switching behaviour and lower EME without a major increase in switching losses. In order to find an optimal trade-off, this work utilizes a monolithic current mode gate driver with a variable output current that can be changed within 10ns. With this driver, measurements with different gate current profiles were taken. The di/dt transition was confirmed to be as important as the dv/dt transition in the power MOSFET. As a result of the improved switching behavior the emissions were reduced by up to 20dB between 7MHz and 60MHz with a switching loss that is 52% lower than with a constantly low gate current.
Galvanic isolated gate drivers require a control signal as well as energy transmission from the control side (lowside) to the driver side (high-side). An additional backward signal transmission is preferred for error signals, status information, etc. This is often realized by means of several transformers or opto-couplers. Decreasing the number of isolation elements results in lower cost and a higher degree of miniaturization. This work presents a gate driver with bidirectional signal transmission and energy transfer via one single transformer. The key concept proposed in this paper is to combine bootstrapping to deliver the main gate charge for the driven power switch with additional energy transfer via the signal transformer. This paper also presents a very efficient combination of energy transfer to two high-side supply rails with back channel amplitude modulation. This way an isolated gate driver can be implemented that allows 100% pulse-width modulation (PWM) duty cycle at low complexity and system cost. The proposed high-side driver IC with integrated power supply, modulation and demodulation circuits was manufactured in a 180nm high-voltage BiCMOS technology. Measurements confirm the concept of bidirectional signal transmission with a 1MBit/s amplitude modulation, 10/20MHz frequency modulation and a maximum power transmission of 14mW via the transformer.
In diesem Beitrag wird ein kapazitiver Low Power DC-DC Wandler mit 15 konfigurierbaren Übersetzungsverhältnissen, einem hohen Eingangsspannungsbereich von 5 V bis 20 V und einer konstanten Ausgangsspannung von 5 V vorgestellt. Bei einer Ausgangsleistung von 5 mW wird ein maximaler Wirkungsgrad von 81% erreicht. Die Implementierung erfolgt in einem 350 nm Hochvolt-CMOS-Prozess. Während es für niedrige Eingangsspannungen eine Vielzahl an Topologien und Konzepten gibt, wurden vollintegrierte SC-Wandler für höhere Eingangsspannungen (> 8 V) bisher nur wenig untersucht. Höhere Spannungen erfordern den Einsatz von Hochvolttransistoren und eine aufwändigere Ansteuerung. Um über einen weiteren Eingangsspannungsbereicht mit hoher Genauigkeit und hohem Wirkungsgrad zu wandeln, erweist sich die Topologie des rekursiven Switched-Capacitor Wandlers (RSC Wandler) als vorteilhaft. In der vorliegenden 4-Bit Implementierung ist der RSC Wandler aus N = 4 2:1 Serien-Parallel Wandler-Zellen aufgebaut. Durch verschiedene Anordnung der einzelnen Zellen können 2ᴺ -1 = 15 Wandlungsverhältnisse realisiert werden. Mittels Rekursion werden in jedem Wandlungsverhältnis alle Kapazitäten genutzt, wodurch die Stromfähigkeit und der Wirkungsgrad des Wandlers deutlich verbessert werden. Einheitliche 2:1 Wandler-Zellen ermöglichen einen modularen Aufbau des Layouts.
Es wird ein hochintegrierter Gatetreiber für 600V-Anwendungen mit einer galvanischen Isolation zwischen der Ansteuerelektronik und der Treiberseite vorgestellt. Eine Besonderheit ist die bidirektionale Signalübertragung und die Energieversorgung über einen einzigen Transformator. Die Treiberansteuersignale werden mittels 10/20 MHz Frequenzmodulation übertragen. Die Signalrückübertragung ist in Form einer 1Mbit/s Amplitudenmodulation realisiert. Die Energieübertragung über den Transformator erlaubt ein dauerhaftes Einschalten des Treibers. Der Energiebedarf während des Schaltvorgangs wird hauptsächlich durch eine Bootstrapschaltung bereitgestellt. Eine weitere Besonderheit ist die Verwendung einer flächeneffizienten Integration einer NMOS Treiberausgangsstufe. Der Gatetreiber wurde in einer 180nm Hochvolt-BiCMOS-Technologie hergestellt. Messungen bestätigen die Funktion des Treibers.
Die vorliegende Erfindung betrifft eine Schaltungsanordnung mit einer Bootstrap-Schaltung, die zumindest eine Hauptkapazität aufweist, von der die erste Seite mit einem ersten Zweig der Schaltungsanordnung und die zweite Seite mit einem auf veränderlichem Potential liegenden zweiten Zweig der Schaltungsanordnung verbunden ist. Die vorgeschlagene Schaltungsanordnung zeichnet sich dadurch aus, dass die Bootstrap-Schaltung parallel zur Hauptkapazität wenigstens eine weitere Kapazität aufweist, die über eine zweite Versorgungsspannung auf eine höhere Spannung aufladbar ist als die Hauptkapazität und über wenigstens ein Schaltelement zur Unterstützung der Hauptkapazität zuschaltbar ist. Bei der vorgeschlagenen Schaltungsanordnung kann in Abhängigkeit von der Dimensionierung der Bootstrap-Kapazitäten eine sehr viel kleinere Fläche mit höherem oder gleich bleibenden Spannungseinbruch oder eine nicht so starke Flächenreduzierung mit kleinerem Spannungseinbruch verglichen mit einer herkömmlichen Bootstrap-Schaltung erzielt werden.
Pegelumsetzer mit einem ersten Eingang, der ein erstes Signal erfasst, wobei das erste Signal einen ersten Spannungspegel aufweist, einem Ausgang, der ein zweites Signal erzeugt, wobei das zweite Signal einen zweiten Spannungspegel aufweist, wobei der zweite Spannungspegel größer als der erste Spannungspegel ist und einem Differenzverstärker, der eine Differenzspannung erfasst, wobei der Differenzverstärker mit einer Versorgungsspannung und einer hochseitige Masse verbunden ist, wobei die Versorgungsspannung ein erstes Spannungspotential und die hochseitige Masse ein zweites Spannungspotential aufweist, dadurch gekennzeichnet, dass der erste Eingang mit einer ersten Teilschaltung verbunden ist, wobei die erste Teilschaltung mit einer zweiten Teilschaltung unidirektional verbunden ist, wobei die zweite Teilschaltung mit der Versorgungsspannung und der hochseitigen Masse verbunden ist, wobei die zweite Teilschaltung mindestens zwei Ausgänge aufweist, die die Differenzspannung des Differenzverstärkers erzeugen, wobei über einen Versorgungsspannungseingang und einen hochseitigen Masseeingang eine zusätzliche Spannung einkoppelt und der Differenzverstärker das zweite Signal in Abhängigkeit der Differenzspannung, der Versorgungsspannung, der hochseitigen Masse und der zusätzlichen Spannung erzeugt.
Die Nachfrage nach kompakten Spannungsversorgungen ist in den letzten Jahren stark gestiegen. Vor allem im Bereich der mobilen Geräte wachsen die Anforderung an die Spannungsversorgung hinsichtlich Bauvolumen und Batterielaufzeit. Für die Vollintegration von DC-DC- Wandlern als „Power Supply on Chip“ ist der SC-Wandler (Switched-Capacitor-Wandler) besonders geeignet. Insbesondere für Low-Power-Anwendungen im Bereich 10 mW kann ein SC-Wandler sehr gut, ohne externe Bauelemente, integriert werden. Während es für niedrige Eingangsspannungen (bis zu 5 V) eine Vielzahl an Topologien und Konzepten gibt, wurden SC-Wandler für höhere Eingangsspannungen (> 8 V) bisher nur wenig untersucht. Dieser Beitrag untersucht die wichtigsten Grundlagen für SC-Wandler mit Schwerpunkt auf hoher und zugleich variabler Eingangsspannung im Bereich 5 - 20 V. Am Beispiel eines Multi-Ratio-Wandlers (Wandler mit mehreren Übersetzungsverhältnissen), dem rekursiven SC-Wandler (RSC- Wandler), werden die Anforderungen eines SC- Wandler für hohe Eingangsspannungen herausgearbeitet und diskutiert.
In dieser Arbeit wird eine optimierte Bandgap-Referenz zur Erzeugung einer temperaturstabilen Spannung und eines Referenzstroms vorgestellt. Für Low-Power-Anwendungen wurde die Bandgap-Referenz, basierend auf der Brokaw-Zelle, mit minimaler Stromaufnahme und optimierter Chipfläche durch Multi-Emitter-Layout der Bipolartransistoren implementiert. Zusätzliches Merkmal ist ein verbreiteter Versorgungsspannungsbereich von 2,5 bis 5,5 V. Simulationen zeigen, dass eine stabile Ausgangsspannung von 1,218 V und ein Referenzstrom von 1,997 μA realisiert wird. Im Temperaturbereich -40 °C … 50 °C sowie dem gesamten Bereich der Versorgungsspannung beträgt die Genauigkeit der Referenzspannung ± 0,04 % mit einer Gesamtstromaufnahme zwischen 3,5 und 10 μA. Es wird eine Temperaturdrift von 2,18 ppm/K erreicht. Durch das elektronische Trimmen von Widerständen wird der Offset der Ausgangsspannung, bedingt durch Herstellungstoleranzen, auf ±3,5 mV justiert. Die Referenz wird in einer 0,18 μm BiCMOS-Technologie implementiert.
Die Erfindung betrifft einen Energieübertrager (100) zur induktiven Energieübertragung von einem primären Schaltkreis (10) des Energieübertragers (100) an eine erste (5) und eine zweite (15) Spannungsdomäne eines sekundären Schaltkreises (20) des Energieübertragers (100) und zur Informationsübertragung vom sekundären Schaltkreis (20) zum primären Schaltkreis (10). Dabei umfasst der Energieübertrager (100): – einen Transformator (30), über den der primäre Schaltkreis (10) und der sekundäre Schaltkreis (20) induktiv miteinander gekoppelt sind und über den sowohl die Energieübertragung als auch die Informationsübertragung erfolgt; und – ein Amplitudenmodulationsmodul (50) zum Modulieren der Strom- und/oder Spannungsamplitude im sekundären Schaltkreis (20) mit Hilfe eines Amplitudenmodulationsschalters (55), wobei der Amplitudenmodulationsschalter (55) zwischen der ersten (5) und zweiten (15) Spannungsdomäne des sekundären Schaltkreises (20) angeordnet ist und ausgelegt ist, durch Öffnen und Schließen des Amplitudenmodulationsschalters (55) die Strom- und/oder Spannungsamplitude im primären Schaltkreis (10) zu ändern, um somit Information vom sekundären Schaltkreis (20) zum primären Schaltkreis (10) zu übertragen. Die vorliegende Erfindung betrifft ferner einen Gate-Treiber zum Schalten eines Leistungsschalters (500) und ein Verfahren zur induktiven Übertragung von Energie und zur kombinierten Informationsübertragung.
Die vorliegende Erfindung betrifft ein Verfahren zur Regelung einer Totzeit in einem Synchronwandler (100), in welchem ein zyklisches Schalten eines Steuerschalters (2) und eines Synchronschalters (3) erfolgen, wobei der Steuerschalter (2) mittels eines ersten Schaltsignals (S1) und der Synchronschalter (3) mittels eines zweiten Schaltsignals (S2) geschaltet werden. Das Verfahren umfasst ein Erfassen und Vorhalten eines Spannungswertes, welcher eine Spannung (VSW) über den Synchronschalter (3) zu einem bestimmten Zeitpunkt beschreibt, und ein Anpassen des ersten und/oder zweiten Schaltsignals (S1, S2) für einen folgenden Zyklus basierend auf dem vorgehaltenen Spannungswert.
Es werden eine elektronische Treiberschaltung und ein Ansteuerverfahren offenbart. Die Treiberschaltung weist einen Ausgang auf; einen ersten Ausgangstransistor mit einem Steuerknoten und einer Laststrecke, wobei die Laststrecke zwischen den Ausgang und einen ersten Versorgungsknoten geschaltet ist; einen Spannungsregler, der dazu ausgebildet ist, eine Spannung über der Laststrecke des ersten Ausgangstransistors zu steuern; und einen ersten Treiber, der dazu ausgebildet ist, den ersten Ausgangstransistor in Abhängigkeit von einem ersten Steuersignal anzusteuern.
A high-voltage replica based current sensor is presented, along with challenges and design techniques which are rarely discussed in literature so far. The performance is evaluated by detailed small signal and large signal analysis. By dedicated placing of high-voltage cascode devices, while keeping as many low-voltage devices as possible, a high gain-bandwidth product is achieved. A decoupling and biasing circuit is introduced which improves the response time of the current sensor at on/off transitions by a factor of five. The current sensor is implemented in a 180nm HV BiCMOS technology. The sensor achieves a DC loop gain of 83 dB and a gain-bandwidth product of 7 MHz. With the proposed techniques, the gain-bandwidth product is increased by a factor of six. The measurable current range is between 60mA and 1.5 A. The performance is demonstrated in a 500 kHz buck converter at an input voltage of 40V. The overall circuit concept is suitable for 100V and beyond, enabling high performance power management designs including switched mode power supplies and motor applications.
Disclosed is an electronic drive circuit and a drive method. The drive circuit includes an output; a first output transistor comprising a control node and a load path, wherein the load path is coupled between the output and a first supply node; a voltage regulator configured to control a voltage across the load path of the first output transistor; and a first driver configured to drive the first output transistor based on a first control signal.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
A highly integrated synchronous buck converter with a predictive dead time control for input voltages >18 V with 10 MHz switching frequency is presented. A high resolution dead time of ˜125 ps allows to reduce dead time dependent losses without requiring body diode conduction to evaluate the dead time. High resolution is achieved by frequency compensated sampling of the switching node and by an 8 bit differential delay chain. Dead time parameters are derived in a comprehensive study of dead time depended losses. This way, the efficiency of fast switching DC-DC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching. High-speed circuit blocks for fast switching operation are presented including level shifter, gate driver, PWM generator. The converter has been implemented in a 180 nm high-voltage BiCMOS technology.
In recent years, significant progress has been made on switched-capacitor DC-DC converters as they enable fully integrated on-chip power management. New converter topologies overcame the fixed input-to-output voltage limitation and achieved high efficiency at high power densities. SC converters are attractive to not only mobile handheld devices with small input and output voltages, but also for power conversion in IoE, industrial and automotive applications, etc. Such applications need to be capable of handling widely varying input voltages of more than 10V, which requires a large amount of conversion ratios. The goal is to achieve a fine granularity with the least number of flying capacitors. In [1] an SC converter was introduced that achieves these goals at low input voltage VIN ≤ 2.5V. [2] shows good efficiency up to VIN = 8V while its conversion ratio is restricted to ≤1/2 with a limited, non-equidistant number of conversion steps. A particular challenge arises with increasing input voltage as several loss mechanisms like parasitic bottom-plate losses and gate-charge losses of high-voltage transistors become of significant influence. High input voltages require supporting circuits like level shifters, auxiliary supply rails etc., which allocate additional area and add losses [2-5]. The combination of both increasing voltage and conversion ratios (VCR) lowers the efficiency and the achievable output power of SC converters. [3] and [5] use external capacitors to enable higher output power, especially for higher VIN. However, this is contradictory to the goal of a fully integrated power supply.
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
Size and cost of a boost converter can be minimized by reducing the voltage overshoot and fastening the transient response in case of load transient. The presented technique improves the transient response of a current mode controlled boost converter, which usually suffers from bandwidth limitation because of its right-half-plane zero (RHPZ). The proposed technique comprises a load current estimation which works as part of a digital controller without any additional measurements. Based on the latest load estimation the controller parameters are adapted, achieving small voltage overshoot and fast transient response. The presented technique was implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology, a Xilinx Spartan-6 field programmable gate array (FPGA), and a TI-ADS8422 analog to-digital-converter (ADC). Simulation and measurements of a 4V-to-6.3V, 500mA boost converter show an improvement of 50% in voltage overshoot and response time to load transient.
The efficiency impact of air-cored inductors used close to and beyond its cut-off frequency in multi-MHz converters is investigated. A method is presented to determine the converter switching frequency that causes the lowest losses in a given inductor. Influential parameters are analysed to optimize an inductor for a predefined switching frequency.
Switched-mode power supplies (SMPS) convert an input DC-voltage into a higher or lower output voltage. In automotive, analog control is mostly used in order to keep the required output voltages constant and resistant to disturbances. The design of robust analog control for SMPS faces parameter variations of integrated and external passive components. Using digital control, parameter variations can be eliminated and the required area for the integrated circuit can be reduced at the same time.
Digital control design bears challenges like the prevention of limit cycle oscillations and controller wind-up. This paper reviews how to prevent these effects. Digital control loops introduce new sources for dead times in the control loop, for example the latency of the analog-to-digitalconverter (ADC). Dead times have negative influence on the stability of the control loop, because they lead to phase delays. Consequently, low latency is one of the key requirements for analog-to-digital converters in digitally controlled SMPS.
Exploiting the example of a 500 kHz-buck converter with a crossover frequency of 70 kHz, this paper shows that the 5 μs-latency of a 16-analog-to-digital-converter leads to a reduction in phase margin of 126°. The latency is less critical for boost converters because of their inherent lower crossover frequencies.
Finally, the paper shows a comparison between analog and digital control of SMPS with regard to chip area and test costs.
The increasing slew rate of modern power switches can increase the efficiency and reduce the size of power electronic applications. This requires a fast and robust signal transmission to the gate driver of the high-side switch. This work proposes a galvanically isolated capacitive signal transmission circuit to increase common mode transient immunity (CMTI). An additional signal path is introduced to significantly improve the transmission robustness for small duty cycles to assure a safe turn-off of the power switch. To limit the input voltage range at the comparator on the secondary side during fast high-side transitions, a clamping structure is implemented. A comparison between a conventional and the proposed signal transmission is performed using transistor level simulations. A propagation delay of about 2 ns over a wide range of voltage transients of up to 300V/ns at input voltages up to 600V is achieved.
In a digitally controlled slope shaping system, reliable detection of both voltage and current slope is required to enable a closed-loop control for various power switches independent of system parameters. In most state-of-the-art works, this is realized by monitoring the absolute voltage and current values. Better accuracy at lower DC power loss is achieved by sensing techniques for a reliable passive detection, which is achieved through avoiding DC paths from the high voltage network into the sensing network. Using a high-speed analog-to-digital converter, the whole waveform of the transient derivative can be stored digitally and prepared for a predictive cycle-by-cycle regulation, without requiring high-precision digital differentiation algorithms. To gain an accurate representation of the voltage and current derivative waveforms, system parasitics are investigated and classified in three sections: (1) component parasitics, which are identified by s-parameter measurements and extraction of equivalent circuit models, (2) PCB design issues related to the sensing circuit, and (3) interconnections between adjacent boards.
The contribution of this paper is an optimized sensing network on the basis of the experimental study supporting fast transition slopes up to 100 V/ns and 1 A/ns and beyond, making the sensing technique attractive for slope shaping of fast switching devices like modern generation IGBTs, CoolMOSTM and SiC mosfets. Measurements of the optimized dv/dt and di/dt setups are demonstrated for a hard switched IGBT power stage.
A concept for a slope shaping gate driver IC is proposed, used to establish control over the slew rates of current and voltage during the turn-on and turn off switching transients.
It combines the high speed and linearity of a fully-integrated closed-loop analog gate driver, which is able to perform real-time regulation, with the advantages of digital control, like flexibility and parameter independency, operating in a predictive cycle-bycycle regulation. In this work, the analog gate drive integrated circuit is partitioned into functional blocks and modeled in the small-signal domain, which also includes the non-linearity of parameters. An analytical stability analysis has been performed in order to ensure full functionality of the system controlling a modern generation IGBT and a superjunction MOSFET. Major parameters of influence, such as gate resistor and summing node capacitance, are investigated to achieve stable control. The large-signal behavior, investigated by simulations of a transistor level design, verifies the correct operation of the circuit. Hence, the gate driver can be designed for robust operation.
Modern power transistors are able to switch at very high transition speed, which can cause EMC violations and overshoot. This is addressed by a gate driver with variable gate current, which is able to control the transition speed. The key idea is that the gate driver can influence the di/dt and dv/dt transition separately and optimize whichever transition promises the highest improvement while keeping switching losses low. To account for changes in the load current, supply voltage, etc., a control loop is required in the driver to ensure optimized switching. In this paper, an efficient control scheme for an automotive gate driver with variable output current capability is presented. The effectiveness of the control loop is demonstrated for a MOSFET bridge consisting of OptiMOS-T2™devices with a total gate charge of 39nC. This bridge setup shows dv/dt transitions between 50 to 1000ns, depending on driving current. The driver is able to switch between gate current levels of 1 to 500mA in 10/15ns (rising/falling transition). With the implemented control loop the driver is measured to significantly reduce the ringing and thereby reduce device stress and electromagnetic emissions while keeping switching losses 52% lower than with a constant current driver.
More and more power electronics applications utilize GaN transistors as they enable higher switching frequencies in comparison to conventional Si devices. Faster switching shrinks down the size of passives and enables compact solutions in applications like renewable energy, electrical cars and home appliances. GaN transistors benefit from ~10× smaller gate charge QG and gate drive voltages in the range of typically 5V vs. ~15V for Si.
Die Erfindung betrifft eine Vorrichtung (100) und ein Verfahren zum elektrischen Verbinden und Trennen zweier elektrischer Potentiale (1, 2). Des Weiteren betrifft die Erfindung eine Verwendung der Vorrichtung (100). Dabei umfasst die Vorrichtung (100): – ein erstes Modul, welches einen ersten und einen zweiten Transistor (10a, 10b) umfasst, wobei der erste Transistor (10a) antiseriell zu dem zweiten Transistor (10b) geschaltet ist; und – ein zweites Modul, welches einen dritten und einen vierten Transistor (10c, 10d) umfasst, wobei der dritte Transistor (10c) antiseriell zu dem vierten Transistor (10d) geschaltet ist; wobei das erste Modul und das zweite Modul parallel geschaltet sind.
The presented wide-Vin step-down converter introduces a parallel-resonant converter (PRC), comprising an integrated 5-bit capacitor array and a 300 nH resonant coil, placed in parallel to a conventional buck converter. Unlike conventional resonant concepts, the implemented soft-switching control eliminates input voltage dependent losses over a wide operating range. This ensures high efficiency across a wide range of Vin= 12-48V, 100-500mA load and 5V output at up to 15MHz switching frequency. The peak efficiency of the converter is 76.3 %. Thanks to the low output current ripple, the output capacitor can be as small as 50 nF, while the inductor tolerates a larger ESR, resulting in small component size. The proposed PRC architecture is also suitable for future power electronics applications using fast-switching GaN devices.
A device including a first and second monitoring unit, the first monitoring unit detecting a first voltage potential and the second monitoring unit detecting a second voltage potential, the monitoring units comparing the first voltage potential and the second voltage potential to the value of the supply voltage and activate a control unit as a function of the comparisons, the control unit determining a switching point in time of a second power transistor, and an arrangement being present which generates current when the second power transistor is being switched on, the current changing the first voltage potential, and the control unit activates a first power transistor when the first voltage potential has the same value as the supply voltage, so that the first power transistor is de-energized.
Erfindungsgemäß wird ein Verfahren zur Optimierung des Betriebs eines in einem Regelkreis für einen Aufwärtswandler vorgesehenen digitalen Reglers (30) zur Verfügung gestellt. Das Verfahren umfasst die folgenden Verfahrensschritte: Auswerten (S1) mindestens einer Ausgangsgröße des digitalen Reglers im Betrieb des Aufwärtswandlers. Schätzen (S2) des instantanen Lastwiderstandswertes (RL) in der Strecke des Regelkreises anhand der mindestens einen ausgewerteten Ausgangsgröße. Einstellen (S3) mindestens eines Reglerkoeffizienten des digitalen Reglers anhand des geschätzten instantanen Lastwiderstandswertes (RL) im Betrieb des Aufwärtswandlers. Erfindungsgemäß bedingt eine Veränderung in der Einstellung des mindestens einen Reglerkoeffizienten eine Veränderung der Transitfrequenz im Regelkreis. Ferner wird ein Regelkreis für einen Aufwärtswandler mit einem digitalen Regler zur Verfügung gestellt, welcher eingerichtet ist, um die Schritte des erfindungsgemäßen Verfahrens durchzuführen. Des Weiteren wird ein Computerprogrammprodukt mit computerausführbarem Programmcode zur Durchführung des erfindungsgemäßen Verfahrens zur Verfügung gestellt.
This article covers the design of highly integrated gate drivers and level shifters for high-speed, high power efficiency and dv/dt robustness with focus on automotive applications. With the introduction of the 48 V board net in addition to the conventional 12 V battery, there is an increasing need for fast switching integrated gate drivers in the voltage range of 50 V and above. State-of-the-art drivers are able to switch 50 V in less than 5 ns. The high-voltage electrical drive train demands for galvanic isolated and highly integrated gate drivers. A gate driver with bidirectional signal transmission with a 1 MBit/s amplitude modulation, 10/20 MHz frequency modulation and power transfer over one single transformer will be discussed. The concept of high-voltage charge storing enables an area-efficient fully integrated bootstrapping supply with 70 % less area consumption. EMC is a major concern in automotive. Gate drivers with slope control optimize EMC while maintaining good switching efficiency. A current mode gate driver, which can change its drive current within 10 ns, results in 20 dBuV lower emissions between 7 and 60 MHz and 52 % lower switching loss compared to a conventional constant current gate driver.
This work presents a fully integrated GaN gate driver in a 180nm HV BCD technology that utilizes high-voltage energy storing (HVES) in an on-chip resonant LC tank, without the need of any external capacitor. It delivers up to 11nC gate charge at a 5V GaN gate, which exceeds prior art by a factor of 45-83, supporting a broad range of GaN transistor types. The stacked LC tank covers an area of only 1.44mm², which corresponds to a superior value of 7.6nC/mm².