Refine
Document Type
- Conference proceeding (221)
- Journal article (28)
Language
- English (249)
Has full text
- yes (249) (remove)
Is part of the Bibliography
- yes (249)
Institute
- Technik (140)
- Informatik (88)
- ESB Business School (19)
- Life Sciences (1)
- Texoversum (1)
Publisher
- IEEE (249) (remove)
Modern power transistors are able to switch at very high transition speed, which can cause EMC violations and overshoot. This is addressed by a gate driver with variable gate current, which is able to control the transition speed. The key idea is that the gate driver can influence the di/dt and dv/dt transition separately and optimize whichever transition promises the highest improvement while keeping switching losses low. To account for changes in the load current, supply voltage, etc., a control loop is required in the driver to ensure optimized switching. In this paper, an efficient control scheme for an automotive gate driver with variable output current capability is presented. The effectiveness of the control loop is demonstrated for a MOSFET bridge consisting of OptiMOS-T2™devices with a total gate charge of 39nC. This bridge setup shows dv/dt transitions between 50 to 1000ns, depending on driving current. The driver is able to switch between gate current levels of 1 to 500mA in 10/15ns (rising/falling transition). With the implemented control loop the driver is measured to significantly reduce the ringing and thereby reduce device stress and electromagnetic emissions while keeping switching losses 52% lower than with a constant current driver.
More and more power electronics applications utilize GaN transistors as they enable higher switching frequencies in comparison to conventional Si devices. Faster switching shrinks down the size of passives and enables compact solutions in applications like renewable energy, electrical cars and home appliances. GaN transistors benefit from ~10× smaller gate charge QG and gate drive voltages in the range of typically 5V vs. ~15V for Si.
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
In recent years, significant progress has been made on switched-capacitor DC-DC converters as they enable fully integrated on-chip power management. New converter topologies overcame the fixed input-to-output voltage limitation and achieved high efficiency at high power densities. SC converters are attractive to not only mobile handheld devices with small input and output voltages, but also for power conversion in IoE, industrial and automotive applications, etc. Such applications need to be capable of handling widely varying input voltages of more than 10V, which requires a large amount of conversion ratios. The goal is to achieve a fine granularity with the least number of flying capacitors. In [1] an SC converter was introduced that achieves these goals at low input voltage VIN ≤ 2.5V. [2] shows good efficiency up to VIN = 8V while its conversion ratio is restricted to ≤1/2 with a limited, non-equidistant number of conversion steps. A particular challenge arises with increasing input voltage as several loss mechanisms like parasitic bottom-plate losses and gate-charge losses of high-voltage transistors become of significant influence. High input voltages require supporting circuits like level shifters, auxiliary supply rails etc., which allocate additional area and add losses [2-5]. The combination of both increasing voltage and conversion ratios (VCR) lowers the efficiency and the achievable output power of SC converters. [3] and [5] use external capacitors to enable higher output power, especially for higher VIN. However, this is contradictory to the goal of a fully integrated power supply.
The presented wide-Vin step-down converter introduces a parallel-resonant converter (PRC), comprising an integrated 5-bit capacitor array and a 300 nH resonant coil, placed in parallel to a conventional buck converter. Unlike conventional resonant concepts, the implemented soft-switching control eliminates input voltage dependent losses over a wide operating range. This ensures high efficiency across a wide range of Vin= 12-48V, 100-500mA load and 5V output at up to 15MHz switching frequency. The peak efficiency of the converter is 76.3 %. Thanks to the low output current ripple, the output capacitor can be as small as 50 nF, while the inductor tolerates a larger ESR, resulting in small component size. The proposed PRC architecture is also suitable for future power electronics applications using fast-switching GaN devices.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
A high-voltage replica based current sensor is presented, along with challenges and design techniques which are rarely discussed in literature so far. The performance is evaluated by detailed small signal and large signal analysis. By dedicated placing of high-voltage cascode devices, while keeping as many low-voltage devices as possible, a high gain-bandwidth product is achieved. A decoupling and biasing circuit is introduced which improves the response time of the current sensor at on/off transitions by a factor of five. The current sensor is implemented in a 180nm HV BiCMOS technology. The sensor achieves a DC loop gain of 83 dB and a gain-bandwidth product of 7 MHz. With the proposed techniques, the gain-bandwidth product is increased by a factor of six. The measurable current range is between 60mA and 1.5 A. The performance is demonstrated in a 500 kHz buck converter at an input voltage of 40V. The overall circuit concept is suitable for 100V and beyond, enabling high performance power management designs including switched mode power supplies and motor applications.
This paper presents a wide-Vin step-down parallel-resonant converter (PRC), comprising an integrated 5-bit capacitor array and a 300-nH resonant coil, placed in parallel to a conventional buck converter. Soft-switching resonant converters are beneficial for high-Vin multi-MHz converters to reduce dominant switching losses, enabling higher switching frequencies. The output filter inductor is optimized based on an empirical study of available inductors. The study shows that faster switching significantly reduces not only the inductor value but also volume, price, and even the inductor losses. In addition, unlike conventional resonant concepts, soft-switching control as part of the proposed PRC eliminates input voltage-dependent losses over a wide operating range, resulting in 76.3% peak efficiency. At Vin = 48 V, a loss reduction of 35% is achieved compared with the conventional buck converter. Adjusting an integrated capacitor array, and selecting the number of oscillation periods, keeps the switching frequency within a narrow range. This ensures high efficiency across a wide range of Vin = 12–48 V, 100–500-mA load, and 5-V output at up to 25-MHz switching frequency. Thanks to the low output current ripple, the output capacitor can be as small
as 50 nF.