Refine
Document Type
Is part of the Bibliography
- yes (49)
Institute
- Technik (49)
Publisher
- IEEE (35)
- VDE Verlag (5)
- Elsevier (3)
This paper presents a measurement setup and an assembly technique suitable for characterization of power semiconductor devices under very high temperature conditions exceeding 500°C. An important application of this is the experimental investigation of wide bandgap semiconductors. Measurement results are shown for a 1200V SiC MOSFET and a 650V depletion mode GaN HEMT.
A TLP system with a very low characteristic impedance of 1.5 Ω and a selectable pulse length from 0.5 to 6 μs is presented. It covers the entire operation region of many power semiconductors up to 700 V and 400 A. Ist applicability is demonstrated by determining the Output characteristics for two Cool MOS devices up to destruction.
The experimental characterization of the thermal impedance Zth of large power MOSFETs is commonly done by measuring the junction temperature Tj in the cooling phase after the device has been heated, preferably to a high junction temperature for increased accuracy. However, turning off a large heating current (as required by modern MOSFETs with low on-state resistances) takes some time because of parasitic inductances in the measurement system. Thus, most setups do not allow the characterization of the junction temperature in the time range below several tens of μs.
In this paper, an optimized measurement setup is presented which allows accurate Tj characterization already 3 μs after turn-off of heating. With this, it becomes possible to experimentally investigate the influence of thermal capacitances close to the active region of the device. Measurement results will be presented for advanced power MOSFETs with very large heating currents up to 220 A. Three bonding variants are investigated and the observed differences will be explained.
Die vorliegende Erfindung betrifft ein Transmission Line Pulssystem zum Erzeugen eines elektrischen Pulses, sowie ein diesbezügliches Verfahren. Dabei umfasst das Transmission Line Pulssystem: eine Transmission Line, eine Energieversorgungsquelle zum Aufladen der Transmission Line und einen Entladungsschalter zum Auslösen einer Entladung der aufgeladenen Transmission Line, dadurch gekennzeichnet, dass die Transmission Line eine Vielzahl von Einzelsegmenten umfasst, wobei jedes Einzelsegment über ein zugehöriges Einstellglied mit einem gemeinsamen Massepotential elektrisch verbunden ist, und wobei zumindest eines der Einstellglieder einen Einstellkondensator und einen Einstellschalter aufweist.
This paper investigates the electrothermal stability and the predominant defect mechanism of a Schottky gate AlGaN/GaN HEMT. Calibrated 3-D electrothermal simulations are performed using a simple semiempirical dc model, which is verified against high-temperature measurements up to 440°C. To determine the thermal limits of the safe operating area, measurements up to destruction are conducted at different operating points. The predominant failure mechanism is identified to be hot-spot formation and subsequent thermal runaway, induced by large drain–gate leakage currents that occur at high temperatures. The simulation results and the high temperature measurements confirm the observed failure patterns.
This paper addresses the turn-on switching process of insulated-gate bipolar transistor (IGBT) modules with anti-parallel free-wheeling diodes (FWD) used in inductive load switching power applications. An increase in efficiency, i.e. decrease in switching losses, calls for a fast switching process of the IGBT, but this commonly implies high values of the reverse-recovery current overshoot. To overcome this undesired behaviour, a solution was proposed which achieves an independent control of the collector current slope and peak reverse recovery current by applying a gate current that is briefly turned negative during the turn-on process. The feasibility of this approach has already been shown, however, a sophisticated control method is required for applying it in applications with varying currents, temperature and device parameters. In this paper a solution based on an adaptive, iterative closed-loop ontrol is proposed. Its effectiveness is demonstrated by experimental results from a 1200 V/200A IGBT power module for different load currents and reverse-recovery current overshoots.
The superior electrical and thermal properties of silicon carbide (SiC) allow further shrinking of the active area of future power semiconductor devices. A lower boundary of the die size can be obtained from the thermal impedance required to withstand the high power dissipation during a short-circuit event. However, this implies that the power distribution is homogeneous and that no current filamentation has to be considered. Therefore, this work investigates this assumption by evaluating the stability of a SiC-MOSFET over a wide range of operation conditions by measurements up to destruction, thermal simulations, and high-temperature characterization.
Integrated power semiconductors are often used for applications with cyclic on-chip power dissipation. This leads to repetitive self-heating and thermo-mechanical stress, causing fatigue on the on-chip metallization and possibly destruction by short circuits. Because of this, an accurate simulation of the thermo-mechanical stress is needed already during the design phase to ensure that lifetime requirements are met. However, a detailed thermo mechanical simulation of the device, including the on-chip metallization is prohibitively time-consuming due to its complex structure, typically consisting of many thin metal lines with thousands of vias. This paper introduces a two-step approach as a solution for this problem. First, a simplified but fast simulation is performed to identify the device parts with the highest stress. After, precise simulations are carried out only for them. The applicability of this method is verified experimentally for LDMOS transistors with different metal configurations. The measured lifetimes and failure locations correlate well with the simulations. Moreover, a strong influence of the layout of the on-chip metallization lifetime was observed. This could also be explained with the simulation
method.
Gallium nitride high electron mobility transistors (GaN-HEMTs) have low capacitances and can achieve low switching losses in applications where hard turn-on is required. Low switching losses imply a fast switching; consequently, fast voltage and current transients occur. However, these transients can be limited by package and layout parasitics even for highly optimized systems. Furthermore, a fast switching requires a fast charging of the input capacitance, hence a high gate current.
In this paper, the switching speed limitations of GaN-HEMTs due to the common source inductance and the gate driver supply voltage are discussed. The turn-on behavior of a GaN-HEMT is simulated and the impact of the parasitics and the gate driver supply voltage on the switching losses is described in detail. Furthermore, measurements are performed with an optimized layout for a drain-source voltage of 500 V and a drain-source current up to 60 A.
Modern power semiconductor devices have low capacitances and can therefore achieve very fast switching transients under hard-switching conditions. However, these transients are often limited by parasitic elements, especially by the source inductance and the parasitic capacitances of the power semiconductor. These limitations cannot be compensated by conventional gate drivers. To overcome this, a novel gate driver approach for power semiconductors was developed. It uses a transformer which accelerates the switching by transferring energy from the source path to the gate path.
Experimental results of the novel gate driver approach show a turn-on energy reduction of 78% (from 80 μJ down to 17 μJ) with a drain-source voltage of 500V and a drain current of 60 A. Furthermore, the efficiency improvement is demonstrated for a hard-switching boost converter. For a switching frequency of 750 kHz with an input voltage of 230V and an output voltage of 400V, it was possible to extend the output power range by 35%(from 2.3kW to 3.1 kW), due to the reduction of the turn-on losses, therefore lowering the junction temperature of the GaN-HEMT.
We present a compact battery charger topology for weight and cost sensitive applications with an average output current of 9A targeted for 36V batteries commonly found in electric bicycles. Instead of using a conventional boost converter with large DC-link capacitors, we accomplish PFC-functionality by shaping the charging current into a sin²-shape. In addition, a novel control scheme without input-current sensing is introduced. A-priori knowledge is used to implement a feed-forward control in combination with a closed-loop output current control to maintain the target current. The use of a full-bridge/half bridge LLC converter enables operation in a wide input-voltage range.
A fully featured prototype has been built with a peak output power of 1050W. An average output power of 400W was measured, resulting in a power density of 1.8 kW/dm³. At 9A charging current, a power factor of 0.96 was measured and the efficiency exceeds 93% on average with passive rectification.
The impact of pulse charging has been evaluated on a 400Wh battery which was charged with the proposed converter as well as CC-CV-charging for reference. Both charging schemes show similar battery surface temperatures.
In this work, a brushless, harmonic-excited wound-rotor synchronous machine is investigated which utilizes special stator and rotor windings. The windings magnetically decouple the fundamental torque-producing field from the harmonic field required for the inductive power transfer to the field coil. In contrast to conventional harmonic-excited synchronous machines, the whole winding is utilized for both torque production and harmonic excitation such that no additional copper for auxiliary windings is needed. Different rotor topologies using rotating power electronic components are investigated and their efficiencies have been compared based on Finite-Element calculation and circuit analysis.
A gate driver approach is presented for the reduction of turn-on losses in hard switching applications. A significant turn-on loss reduction of up to 55% has been observed for SiCMOSFETs. The gate driver approach uses a transformer which couples energy from the power path back into the gate path during switching events, providing increased gate driver current and thereby faster switching speed.
The gate driver approach was tested on a boost converter running at a switching frequency up to 300 kHz. With an input voltage of 300V and an output voltage of 600V, it was possible to reduce the converter losses by 8% at full load. Moreover, the output power range could be extended by 23% (from 2.75kW to 3.4 kW) due to the reduction of the turn-on losses.
In this work we investigate the behavior of MIS- and Schottky-gate AlGaN/GaN HEMTs under high-power pulsestress. A special setup capable of applying pulses of constant power is used to evaluate the electro-thermal response in different operating points. For both types of devices, the time to failure was found to decrease with increasing drain-source voltage. Overall, the Schottky-gate device displays a higher pulse robustness. The pulse withstand time of the MIS-gate device is limited by the occurrence of a thermal instability at approximately 240°C while the Schottky-gate device displays a rapid increase of the gate leakage current prior to failure. The mechanism responsible for this gate current is further investigated by static and transient temperature measurements and yielded activation energies of 0.6 eV and 0.84 eV.
LDMOS transistors in integrated power technologies are often subject to thermo-mechanical stress, which degrades the on-chip metallization and eventually leads to a short. This paper investigates small sense lines embedded in the LDMOS metallization. It will be shown that their resistance depends strongly on the stress cycle number. Thus, they can be used as aging sensors and predict impending failures. Different test structures have been investigated to identify promising layout configurations. Such sensors are key components for resilient systems that adaptively reduce stress to allow aggressive LDMOS scaling without increasing the risk of failure.
A novel configuration of the dual active bridge (DAB) DC/DC converter is presented, enabling more efficient wide voltage range conversion at light loads. A third phase leg as well as a center tapped transformer are introduced to one side of the converter. This concept provides two different turn ratios, thus extending the zero voltage switching operation resulting in higher efficiency. A laboratory prototype was built converting an input voltage of 40V to an output voltage in the range of 350V to 650V. Measurements show a significant increase up to 20% in the efficiency for light-load operation.
This paper presents a control strategy for optimal utilization of photovoltaic (PV) generated power in conjunction with an Energy Storage System (ESS). The ESS is specifically designed to be retrofitted into existing PV systems in an end-user application. It can be attached in parallel to the PV system and connects to existing DC/AC inverters. In particular, the study covers the impact such a modification has on the output power of existing PV panels. A distinct degradation of PV output power was found due to the different power characteristics of PV panel and ESS. To overcome such degradation a novel feedback system is proposed. The feedback system continuously modifies the power characteristic of the ESS to match the PV panel and thus achieves optimal power utilization. Impact on PV and power point tracking performance is analyzed. Simulation of the proposed system is performed in MATLAB/Simulink. The results are found to be satisfactory.
Many GaN power transistors contain a PN junction between gate and the channel region close to the source. In order to maintain the on-state, current must continuously be supplied to the junction. Therefore, the commonly recommended approach uses a gate bias voltage of 12V to compensate the Miller current through a boost circuit. For the same purpose, a novel gate driving method based on an inductive feed forward has been presented. With this, stable turn-on can be achieved even for a bias voltage of only 5V. The effectiveness of this concept is demonstrated by double pulse measurements, switching currents up to 27A and a voltage of 400V. For both approaches a compact design with low source inductance is characterized. In addition to the significant reduction of the gate bias voltage and peak gate current, the new approach reduces the switching losses for load currents >23 A.
We present a dual active bridge topology suitable for wide voltage range applications covering all combinations of 200V to 600V on the input and 20V to 60V on the output with constant power of 1kW.We employ a stepped inductance scheme to adjust the effective inductance of the converter, thus extending the efficient operation range. Using a variable switching frequency between 35 kHz and 150 kHz with operation-point-dependent limits further increases the performance of the converter. A prototype was built and the proposed changes have been compared to a fixed frequency, fixed inductance implementation. Measurements show a maximum loss reduction of 40 %, leading to a peak efficiency of 97% while maintaining constant output power over the entire working area.