Refine
Document Type
Is part of the Bibliography
- yes (49)
Institute
- Technik (49)
Publisher
- IEEE (35)
- Elsevier (3)
- VDE Verlag GmbH (2)
- VDE-Verlag (2)
- VDE Verlag (1)
IGBT modules with anti-parallel FWDs are widely used in inductive load switching power applications, such as motor drive applications. Nowadays there is a continuous effort to increase the efficiency of such systems by decreasing their switching losses. This paper addresses the problems arising in the turn-on process of an IGBT working in hard-switching conditions. A method is proposed which achieves – contrary to most other approaches – a high switching speed and, at the same time, a low peak reverse-recovery current. This is done by applying an improved gate current waveform that is briefly lowered during the turn-on process. The proposed method achieves low switching losses. Its effectiveness is demonstrated by experimental results with IGBT modules for 600V and 1200V.
Die vorliegende Erfindung betrifft ein Transmission Line Pulssystem zum Erzeugen eines elektrischen Pulses, sowie ein diesbezügliches Verfahren. Dabei umfasst das Transmission Line Pulssystem: eine Transmission Line, eine Energieversorgungsquelle zum Aufladen der Transmission Line und einen Entladungsschalter zum Auslösen einer Entladung der aufgeladenen Transmission Line, dadurch gekennzeichnet, dass die Transmission Line eine Vielzahl von Einzelsegmenten umfasst, wobei jedes Einzelsegment über ein zugehöriges Einstellglied mit einem gemeinsamen Massepotential elektrisch verbunden ist, und wobei zumindest eines der Einstellglieder einen Einstellkondensator und einen Einstellschalter aufweist.
This paper addresses the turn-on switching process of insulated-gate bipolar transistor (IGBT) modules with anti-parallel free-wheeling diodes (FWD) used in inductive load switching power applications. An increase in efficiency, i.e. decrease in switching losses, calls for a fast switching process of the IGBT, but this commonly implies high values of the reverse-recovery current overshoot. To overcome this undesired behaviour, a solution was proposed which achieves an independent control of the collector current slope and peak reverse recovery current by applying a gate current that is briefly turned negative during the turn-on process. The feasibility of this approach has already been shown, however, a sophisticated control method is required for applying it in applications with varying currents, temperature and device parameters. In this paper a solution based on an adaptive, iterative closed-loop ontrol is proposed. Its effectiveness is demonstrated by experimental results from a 1200 V/200A IGBT power module for different load currents and reverse-recovery current overshoots.
Modern power DMOS transistors greatly benefit from the continuous advances of the technology, which yield devices with very low area-specific RDS,on figures of merit and therefore allow for significantly reduced active areas. However, in many applications, where the devices must dissipate high amounts of energy and thus are subjected to significant self-heating, the active area is not dictated by RDS,on requirements, but by the energy constraints. In this paper, a simple method of improving the energy capability and reliability of power DMOS transistors operating in pulsed conditions is proposed and experimentally verified. The method consists in redistributing the power density from the hotter to the cooler device regions, hence achieving a more homogeneous temperature distribution and a reduced peak temperature. To demonstrate the principle, a simple gate offset circuit is used to redistribute the current density to the cooler DMOS parts. No technology changes are needed for the implementation, only minor changes to the driver circuit are necessary, with a minimal impact on the additional required active area. Improvements in the energy capability from 9.2% up to 39% have been measured. Furthermore, measurements have shown that the method remains effective also if the operating conditions change significantly. The simplicity and the effectiveness of the implementation makes the proposed method suitable to be used in a wide range of applications.
A TLP system with a very low characteristic impedance of 1.5 Ω and a selectable pulse length from 0.5 to 6 μs is presented. It covers the entire operation region of many power semiconductors up to 700 V and 400 A. Ist applicability is demonstrated by determining the Output characteristics for two Cool MOS devices up to destruction.
An experimental study of a zero voltage switching SiC boost converter with an active snubber network
(2015)
This paper presents a quasi-resonant, zero voltage switching (ZVS) SiC boost converter for an output power of up to 10 kW. The converter is realized with an easily controllable active snubber network that allows a reduction of switching losses by minimizing the voltage stress applied to the active switch. With this approach, an increase of the switching frequency is possible, allowing a reduction of the system size. Experiments show a maximum converter efficiency up to 99.2% for a switching frequency of 100 kHz. A second version of the converter enables a further size reduction by increasing the switching frequency to 300 kHz while still reaching a high efficiency up to 98.4 %.
Gallium nitride high electron mobility transistors (GaN-HEMTs) have low capacitances and can achieve low switching losses in applications where hard turn-on is required. Low switching losses imply a fast switching; consequently, fast voltage and current transients occur. However, these transients can be limited by package and layout parasitics even for highly optimized systems. Furthermore, a fast switching requires a fast charging of the input capacitance, hence a high gate current.
In this paper, the switching speed limitations of GaN-HEMTs due to the common source inductance and the gate driver supply voltage are discussed. The turn-on behavior of a GaN-HEMT is simulated and the impact of the parasitics and the gate driver supply voltage on the switching losses is described in detail. Furthermore, measurements are performed with an optimized layout for a drain-source voltage of 500 V and a drain-source current up to 60 A.
Modern power semiconductor devices have low capacitances and can therefore achieve very fast switching transients under hard-switching conditions. However, these transients are often limited by parasitic elements, especially by the source inductance and the parasitic capacitances of the power semiconductor. These limitations cannot be compensated by conventional gate drivers. To overcome this, a novel gate driver approach for power semiconductors was developed. It uses a transformer which accelerates the switching by transferring energy from the source path to the gate path.
Experimental results of the novel gate driver approach show a turn-on energy reduction of 78% (from 80 μJ down to 17 μJ) with a drain-source voltage of 500V and a drain current of 60 A. Furthermore, the efficiency improvement is demonstrated for a hard-switching boost converter. For a switching frequency of 750 kHz with an input voltage of 230V and an output voltage of 400V, it was possible to extend the output power range by 35%(from 2.3kW to 3.1 kW), due to the reduction of the turn-on losses, therefore lowering the junction temperature of the GaN-HEMT.
The experimental characterization of the thermal impedance Zth of large power MOSFETs is commonly done by measuring the junction temperature Tj in the cooling phase after the device has been heated, preferably to a high junction temperature for increased accuracy. However, turning off a large heating current (as required by modern MOSFETs with low on-state resistances) takes some time because of parasitic inductances in the measurement system. Thus, most setups do not allow the characterization of the junction temperature in the time range below several tens of μs.
In this paper, an optimized measurement setup is presented which allows accurate Tj characterization already 3 μs after turn-off of heating. With this, it becomes possible to experimentally investigate the influence of thermal capacitances close to the active region of the device. Measurement results will be presented for advanced power MOSFETs with very large heating currents up to 220 A. Three bonding variants are investigated and the observed differences will be explained.