Refine
Document Type
- Conference proceeding (33)
- Journal article (7)
Language
- English (40)
Has full text
- yes (40) (remove)
Is part of the Bibliography
- yes (40)
Institute
- Technik (40)
Publisher
- IEEE (35)
- Elsevier (2)
- VDE Verlag (1)
- VDE Verlag GmbH (1)
- VDE-Verlag (1)
Advanced power semiconductors such as DMOS transistors are key components of modern power electronic systems. Recent discrete and integrated DMOS technologies have very low area-specific on-state resistances so that devices with small sizes can be chosen. However, their power dissipation can sometimes be large, for example in fault conditions, causing the device temperature to rise significantly. This can lead to excessive temperatures, reduced lifetime, and possibly even thermal runaway and subsequent destruction. Therefore, it is required to ensure already in the design phase that the temperature always remains in an acceptable range. This paper will show how self-heating in DMOS transistors can be experimentally determined with high accuracy. Further, it will be discussed how numerical electrothermal simulations can be carried out efficiently, allowing the accurate assessment of self-heating within a few minutes. The presented approach has been successfully verified experimentally for device temperatures exceeding 500 ◦C up to the onset of thermal runaway.
DMOS transistors are often subject to high power dissipation and thus substantial self-heating. This limits their safe operating area because very high device temperatures can lead to thermal runaway and subsequent destruction. Because the peak temperature usually occurs only in a small region in the device, it is possible to redistribute part of the dissipated power from the hot region to the cooler device areas. In this way, the peak temperature is reduced, whereas the total power dissipation is still the same. Assuming that a certain temperature must not be exceeded for safe operation, the improved device is now capable of withstanding higher amounts of energy with an unchanged device area. This paper presents two simple methods to redistribute the power dissipation density and thus lower the peak device temperature. The presented methods only require layout changes. They can easily be applied to modern power technologies without the need of process modifications. Both methods are implemented in test structures and investigated by simulations and measurements.
DMOS transistors in integrated power technologies are often subject to significant self-heating and thus high temperatures, which can lead to device failure and reduced lifetime. Hence, it must be ensured that the device temperature does not rise too much. For this, the influence of the on-chip metallization must be taken into account because of the good thermal conductivity and significant thermal capacitance of the metal layers on top of the active DMOS area. In this paper, test structures with different metal layers and vias configurations are presented that can be used to determine the influence of the onchip metallization on the temperature caused by self-heating. It will be shown how accurate results can be obtained to determine even the influence of small changes in the metallization. The measurement results are discussed and explained, showing how on-chip metallization helps to lower the device temperature. This is further supported by numerical simulations. The obtained insights are valuable for technology optimization, but are also useful for calibration of temperature simulators.
In this work, a brushless, harmonic-excited wound-rotor synchronous machine is investigated which utilizes special stator and rotor windings. The windings magnetically decouple the fundamental torque-producing field from the harmonic field required for the inductive power transfer to the field coil. In contrast to conventional harmonic-excited synchronous machines, the whole winding is utilized for both torque production and harmonic excitation such that no additional copper for auxiliary windings is needed. Different rotor topologies using rotating power electronic components are investigated and their efficiencies have been compared based on Finite-Element calculation and circuit analysis.
We present a compact battery charger topology for weight and cost sensitive applications with an average output current of 9A targeted for 36V batteries commonly found in electric bicycles. Instead of using a conventional boost converter with large DC-link capacitors, we accomplish PFC-functionality by shaping the charging current into a sin²-shape. In addition, a novel control scheme without input-current sensing is introduced. A-priori knowledge is used to implement a feed-forward control in combination with a closed-loop output current control to maintain the target current. The use of a full-bridge/half bridge LLC converter enables operation in a wide input-voltage range.
A fully featured prototype has been built with a peak output power of 1050W. An average output power of 400W was measured, resulting in a power density of 1.8 kW/dm³. At 9A charging current, a power factor of 0.96 was measured and the efficiency exceeds 93% on average with passive rectification.
The impact of pulse charging has been evaluated on a 400Wh battery which was charged with the proposed converter as well as CC-CV-charging for reference. Both charging schemes show similar battery surface temperatures.
The Dual Active Bridge (DAB) is a very promising topology for future power converters. However, careless operation can lead to a DC component in the transformer current. The problem is further exacerbated when the phase shift changes during operation. This work presents a study of DC bias effects on the DAB with special regard to transient effects introduced by sudden shifts in the output load. We present a simple yet effective approach to avoid DC bias entirely.
A novel brushless excitation concept for synchronous machines with a rotating power converter is proposed in this paper. The concept does not need an auxiliary winding or any other modification to the machine structure apart from an inverter with a DC link capacitor and a controller on the rotor. The power required for the rotor excitation is provided by injecting harmonics into the stator winding. Thus, a voltage in the field coil is induced. The rotor inverter is controlled such that the alternating current charges the DC link capacitor. At the same time the inverter supplies the DC field current to the field coil. The excitation concept is first developed in theory, then presented using an analytical model and FEA, and lastly investigated with a prelimininary experimental setup.
In this work design rules for a novel brushless excitation system for externally excited synchronous machines are discussed. The concept replaces slip rings with a fullbridge active rectifier and a controller mounted on the rotor. An AC signal induced from the stator is used to charge the rotor DC link. The DC current for the rotor excitation is provided from this DC link source. Finite element analysis of an existing machine is used to analyze the practicability of the excitation system.
Improved inductive feed-forward for fast turn-on of power semiconductors during hard switching
(2019)
A transformer is used to increase the gate voltage during turn-on, thus reducing the necessary bias voltage of the gate driver. Counteracting the voltage dependency of the gate capacitance of high-voltage power devices, faster transitions are possible. The additional transformer only slighly increases the over-voltage during turn-off.
Novel design for a coreless printed circuit board transformer realizing high bandwidth and coupling
(2019)
Rogowski coils offer galvanic isolation and can measure alternating currents with a high bandwidth. Coreless printed circuit board (PCB) transformers have been used as an alternative to limit the additional stray inductance if a Rogowski coil can not be attached to the circuit. A new PCB transformer layout is proposed to reduce cost, decrease additional stray inductance, increase the bandwidth of current measurements and simplify the integration into existing designs.