Refine
Document Type
- Conference proceeding (33)
- Journal article (7)
Language
- English (40)
Has full text
- yes (40) (remove)
Is part of the Bibliography
- yes (40)
Institute
- Technik (40)
Publisher
- IEEE (35)
- VDE Verlag (3)
- Elsevier (2)
Advanced power semiconductors such as DMOS transistors are key components of modern power electronic systems. Recent discrete and integrated DMOS technologies have very low area-specific on-state resistances so that devices with small sizes can be chosen. However, their power dissipation can sometimes be large, for example in fault conditions, causing the device temperature to rise significantly. This can lead to excessive temperatures, reduced lifetime, and possibly even thermal runaway and subsequent destruction. Therefore, it is required to ensure already in the design phase that the temperature always remains in an acceptable range. This paper will show how self-heating in DMOS transistors can be experimentally determined with high accuracy. Further, it will be discussed how numerical electrothermal simulations can be carried out efficiently, allowing the accurate assessment of self-heating within a few minutes. The presented approach has been successfully verified experimentally for device temperatures exceeding 500 ◦C up to the onset of thermal runaway.
DMOS transistors are often subject to high power dissipation and thus substantial self-heating. This limits their safe operating area because very high device temperatures can lead to thermal runaway and subsequent destruction. Because the peak temperature usually occurs only in a small region in the device, it is possible to redistribute part of the dissipated power from the hot region to the cooler device areas. In this way, the peak temperature is reduced, whereas the total power dissipation is still the same. Assuming that a certain temperature must not be exceeded for safe operation, the improved device is now capable of withstanding higher amounts of energy with an unchanged device area. This paper presents two simple methods to redistribute the power dissipation density and thus lower the peak device temperature. The presented methods only require layout changes. They can easily be applied to modern power technologies without the need of process modifications. Both methods are implemented in test structures and investigated by simulations and measurements.
DMOS transistors in integrated power technologies are often subject to significant self-heating and thus high temperatures, which can lead to device failure and reduced lifetime. Hence, it must be ensured that the device temperature does not rise too much. For this, the influence of the on-chip metallization must be taken into account because of the good thermal conductivity and significant thermal capacitance of the metal layers on top of the active DMOS area. In this paper, test structures with different metal layers and vias configurations are presented that can be used to determine the influence of the onchip metallization on the temperature caused by self-heating. It will be shown how accurate results can be obtained to determine even the influence of small changes in the metallization. The measurement results are discussed and explained, showing how on-chip metallization helps to lower the device temperature. This is further supported by numerical simulations. The obtained insights are valuable for technology optimization, but are also useful for calibration of temperature simulators.
Modern power DMOS transistors greatly benefit from the continuous advances of the technology, which yield devices with very low area-specific RDS,on figures of merit and therefore allow for significantly reduced active areas. However, in many applications, where the devices must dissipate high amounts of energy and thus are subjected to significant self-heating, the active area is not dictated by RDS,on requirements, but by the energy constraints. In this paper, a simple method of improving the energy capability and reliability of power DMOS transistors operating in pulsed conditions is proposed and experimentally verified. The method consists in redistributing the power density from the hotter to the cooler device regions, hence achieving a more homogeneous temperature distribution and a reduced peak temperature. To demonstrate the principle, a simple gate offset circuit is used to redistribute the current density to the cooler DMOS parts. No technology changes are needed for the implementation, only minor changes to the driver circuit are necessary, with a minimal impact on the additional required active area. Improvements in the energy capability from 9.2% up to 39% have been measured. Furthermore, measurements have shown that the method remains effective also if the operating conditions change significantly. The simplicity and the effectiveness of the implementation makes the proposed method suitable to be used in a wide range of applications.
Large power semiconductors are complex structures, their metallization usually containing many thousands of contacts or vias. Because of this, detailed FEM simulations of the whole device are nowadays not possible because of excessive simulation time.
This paper introduces a simulation approach which allows quick identification of critical regions with respect to lifetime by a simplified simulation. For this, the complex layers are replaced by a much simpler equivalent layer, allowing a simulation of the whole device even including its package. In a second step, precise simulations taking all details of the structure into account are carried out, but only for the critical regions of interest. Thus, this approach gives detailed results where required with consideration of the whole structure including packaging. Further, the simulation time requirements are very moderate.
DMOS transistors in integrated smart power technologies are often subject to cyclic power dissipation with substantial selfheating. This leads to repetitive thermo mechanical stress, causing fatigue of the on-chip metallization and limiting the lifetime. Hence, most designs use large devices for lower peak temperatures and thus reduced stress to avoid premature failures.
However, significantly smaller DMOS transistors are acceptable if the system reverts to a safer operating condition with lower stress when a failure is expected to occur in the near future. Hence, suitable early-warning sensors are required. This paper proposes a floating metal meander embedded between DMOS source and drain to detect an impending metallization failure. Measurement results of several variants will be presented and discussed, investigating their suitability as early warning indicators.
An experimental study of a zero voltage switching SiC boost converter with an active snubber network
(2015)
This paper presents a quasi-resonant, zero voltage switching (ZVS) SiC boost converter for an output power of up to 10 kW. The converter is realized with an easily controllable active snubber network that allows a reduction of switching losses by minimizing the voltage stress applied to the active switch. With this approach, an increase of the switching frequency is possible, allowing a reduction of the system size. Experiments show a maximum converter efficiency up to 99.2% for a switching frequency of 100 kHz. A second version of the converter enables a further size reduction by increasing the switching frequency to 300 kHz while still reaching a high efficiency up to 98.4 %.
DMOS transistors often suffer from substantial self-heating during high power dissipation, which can lead to thermal destruction if the device temperature reaches excessive values. A successfully demonstrated method to reduce the peak temperature is the redistribution of power dissipation density from the hotter to the cooler device areas by careful layout modification. However, this is very tedious and time-consuming if complex-shaped devices as often found in industrial applications are considered.
This paper presents an approach for fully automatic layout optimization which requires only a few hours processing time. The approach is applied to complex shaped test structures which are investigated by measurements and electro-thermal simulations. Results show a significantly lower peak temperature and an energy capability gain of 84 %, offering potential for a 18 % size reduction of active area.
This paper presents a measurement setup and an assembly technique suitable for characterization of power semiconductor devices under very high temperature conditions exceeding 500°C. An important application of this is the experimental investigation of wide bandgap semiconductors. Measurement results are shown for a 1200V SiC MOSFET and a 650V depletion mode GaN HEMT.
A TLP system with a very low characteristic impedance of 1.5 Ω and a selectable pulse length from 0.5 to 6 μs is presented. It covers the entire operation region of many power semiconductors up to 700 V and 400 A. Ist applicability is demonstrated by determining the Output characteristics for two Cool MOS devices up to destruction.