Refine
Document Type
- Conference proceeding (39) (remove)
Is part of the Bibliography
- yes (39)
Institute
- Technik (39)
Publisher
- IEEE (30)
- VDE Verlag GmbH (2)
- VDE-Verlag (2)
- VDE Verlag (1)
The superior electrical and thermal properties of silicon carbide (SiC) allow further shrinking of the active area of future power semiconductor devices. A lower boundary of the die size can be obtained from the thermal impedance required to withstand the high power dissipation during a short-circuit event. However, this implies that the power distribution is homogeneous and that no current filamentation has to be considered. Therefore, this work investigates this assumption by evaluating the stability of a SiC-MOSFET over a wide range of operation conditions by measurements up to destruction, thermal simulations, and high-temperature characterization.
The loss contribution of a 2.3kW synchronous GaN-HEMT boost converter for an input voltage of 250V and an output voltage of 500V was analyzed. A simulation model which consists of two parts is introduced. First, a physics-based model is used to determine the switching losses. Then, a system simulation is applied to calculate the losses of the specific elements. This approach allows a fast and accurate system evaluation as required for further system optimization.
In this work, a hard- and a zero-voltage turn-on switching converter are compared. Measurements were performed to verify the simulation model, showing a good agreement. A peak efficiency of 99% was achieved for an output power of 1.4kW. Even with an output power above 400W, it was possible to obtain a system efficiency exceeding 98 %.
Influence of metallization layout on aging detector lifetime under cyclic thermo-mechanical stress
(2016)
The influence of the layout on early warning detectors in BCD technologies for metallization failure under cyclic thermo-mechanical stress was investigated. Different LDMOS transistors, with narrow or wide metal fingers and with or without embedded detectors, were used. The test structures were repeatedly stressed by pronounced self-heating until failure (a short circuit) was detected. The results show that the layout of the on-chip metallization has a large impact on the lifetime. A significant influence of the detectors on the lifetime was also observed, in our case causing a reduction of more than a factor of two, but only for the test structure with narrow metal fingers. The experimental results are explained by an efficient numerical thermo mechanical simulation approach, giving detailed insights into the strain distribution in the metal system. These results are important for aging detector design and, morever, for LDMOS on-chip metal layout in general.
This work investigates the electro-thermal behavior and failure mechanism of a 600V depletion-mode GaN HEMT by experimental analysis and numerical thermal simulations. For this device, the positive temperature coefficient of the draingate leakage current can lead to the formation of hot spots. This localized thermal runaway which ultimately results in a breakdown of the inherent drain-gate junction is found to be the dominant cause of failure.
This paper presents an efficient implementation of a reconfigurable battery stack which allows full exploitation of the capacity of every single cell. Contrary to most other approaches, it is possible to electrically remove one or more cells from the battery stack. Therefore, the overall capacity of the system is not restricted by the weaker cells, and cells with very different states of health can be used, making the system very attractive for refurbished batteries. For the required switches, low-voltage high-current MOSFETs are used. A demonstrator has been built with a total capacity of up to 3.5 kWh, a nominal voltage of 35 V, and currents up 200 A.
This paper presents a compact 3 kW bidirectional GaN-HEMT DC/DC converter for 360V to 400-500 V. A very high efficiency has been reached by applying a zero voltage turn-on in conjunction with a negative gate-source voltage, even though normally-off HEMTs are used. Further improvements were achieved by adapting the switching frequency to the load current and output voltage, as will be explained by means of the loss contribution of the specific elements for a constant and an adaptive switching frequency. Measurements have shown a high converter efficiency exceeding 99% over a wide output power range of up to 3 kW.
In this work, a comparison between different brushless harmonic-excited wound-rotor synchronous machines is performed. The general idea of all topologies is the elimination of the slip rings and auxiliary windings by using the already existing stator and rotor winding for field excitation. This is achieved by injecting a harmonic airgap field with the help of power electronics. This harmonic field does not interact with the fundamental field, it just transfers the excitation power across the airgap. Alternative methods with varying number of phases, different pole-pair combinations, and winding layouts are covered and compared with a detailed Finite-Element-parameterized model. Parasitic effects due to saturation and coupling between the harmonic and main windings are considered.
In this work, a brushless, harmonic-excited wound-rotor synchronous machine without any auxiliary windings which can provide full torque at startup is investigated experimentally. The excitation power is transferred inductively by superimposing an additional harmonic field of different pole-pair number on top of the airgap field. This is achieved by feeding the parallel paths of the stator and rotor winding separately. A prototype for the harmonic-excited synchronous machine has been constructed and experimental results are presented to verify the concept. The main loss contributors are identified and the importance of considering core losses under harmonic excitation is discussed. A general analytical model for harmonic excited synchronous machines is proposed which enables a quick estimation of the iron core flux densities and the core losses generated by the additional harmonic currents.