Refine
Document Type
Is part of the Bibliography
- yes (18)
Institute
- Technik (18)
Publisher
- IEEE (12)
- Hochschule Ulm (2)
- Copernicus GmbH (1)
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
The presented wide-Vin step-down converter introduces a parallel-resonant converter (PRC), comprising an integrated 5-bit capacitor array and a 300 nH resonant coil, placed in parallel to a conventional buck converter. Unlike conventional resonant concepts, the implemented soft-switching control eliminates input voltage dependent losses over a wide operating range. This ensures high efficiency across a wide range of Vin= 12-48V, 100-500mA load and 5V output at up to 15MHz switching frequency. The peak efficiency of the converter is 76.3 %. Thanks to the low output current ripple, the output capacitor can be as small as 50 nF, while the inductor tolerates a larger ESR, resulting in small component size. The proposed PRC architecture is also suitable for future power electronics applications using fast-switching GaN devices.
This paper presents a wide-Vin step-down parallel-resonant converter (PRC), comprising an integrated 5-bit capacitor array and a 300-nH resonant coil, placed in parallel to a conventional buck converter. Soft-switching resonant converters are beneficial for high-Vin multi-MHz converters to reduce dominant switching losses, enabling higher switching frequencies. The output filter inductor is optimized based on an empirical study of available inductors. The study shows that faster switching significantly reduces not only the inductor value but also volume, price, and even the inductor losses. In addition, unlike conventional resonant concepts, soft-switching control as part of the proposed PRC eliminates input voltage-dependent losses over a wide operating range, resulting in 76.3% peak efficiency. At Vin = 48 V, a loss reduction of 35% is achieved compared with the conventional buck converter. Adjusting an integrated capacitor array, and selecting the number of oscillation periods, keeps the switching frequency within a narrow range. This ensures high efficiency across a wide range of Vin = 12–48 V, 100–500-mA load, and 5-V output at up to 25-MHz switching frequency. Thanks to the low output current ripple, the output capacitor can be as small
as 50 nF.
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.
A highly integrated synchronous buck converter with a predictive dead time control for input voltages >18 V with 10 MHz switching frequency is presented. A high resolution dead time of ˜125 ps allows to reduce dead time dependent losses without requiring body diode conduction to evaluate the dead time. High resolution is achieved by frequency compensated sampling of the switching node and by an 8 bit differential delay chain. Dead time parameters are derived in a comprehensive study of dead time depended losses. This way, the efficiency of fast switching DC-DC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching. High-speed circuit blocks for fast switching operation are presented including level shifter, gate driver, PWM generator. The converter has been implemented in a 180 nm high-voltage BiCMOS technology.
Switched-mode power supplies (SMPS) convert an input DC-voltage into a higher or lower output voltage. In automotive, analog control is mostly used in order to keep the required output voltages constant and resistant to disturbances. The design of robust analog control for SMPS faces parameter variations of integrated and external passive components. Using digital control, parameter variations can be eliminated and the required area for the integrated circuit can be reduced at the same time.
Digital control design bears challenges like the prevention of limit cycle oscillations and controller wind-up. This paper reviews how to prevent these effects. Digital control loops introduce new sources for dead times in the control loop, for example the latency of the analog-to-digitalconverter (ADC). Dead times have negative influence on the stability of the control loop, because they lead to phase delays. Consequently, low latency is one of the key requirements for analog-to-digital converters in digitally controlled SMPS.
Exploiting the example of a 500 kHz-buck converter with a crossover frequency of 70 kHz, this paper shows that the 5 μs-latency of a 16-analog-to-digital-converter leads to a reduction in phase margin of 126°. The latency is less critical for boost converters because of their inherent lower crossover frequencies.
Finally, the paper shows a comparison between analog and digital control of SMPS with regard to chip area and test costs.
Erfindungsgemäß wird ein Verfahren zur Optimierung des Betriebs eines in einem Regelkreis für einen Aufwärtswandler vorgesehenen digitalen Reglers (30) zur Verfügung gestellt. Das Verfahren umfasst die folgenden Verfahrensschritte: Auswerten (S1) mindestens einer Ausgangsgröße des digitalen Reglers im Betrieb des Aufwärtswandlers. Schätzen (S2) des instantanen Lastwiderstandswertes (RL) in der Strecke des Regelkreises anhand der mindestens einen ausgewerteten Ausgangsgröße. Einstellen (S3) mindestens eines Reglerkoeffizienten des digitalen Reglers anhand des geschätzten instantanen Lastwiderstandswertes (RL) im Betrieb des Aufwärtswandlers. Erfindungsgemäß bedingt eine Veränderung in der Einstellung des mindestens einen Reglerkoeffizienten eine Veränderung der Transitfrequenz im Regelkreis. Ferner wird ein Regelkreis für einen Aufwärtswandler mit einem digitalen Regler zur Verfügung gestellt, welcher eingerichtet ist, um die Schritte des erfindungsgemäßen Verfahrens durchzuführen. Des Weiteren wird ein Computerprogrammprodukt mit computerausführbarem Programmcode zur Durchführung des erfindungsgemäßen Verfahrens zur Verfügung gestellt.
Boost converters suffer from a bandwidth limitation caused by the right-half plane zero (RHPZ), which occurs in the control-to-output transfer function. In contrast, there are many applications that require superior dynamic behavior. Further, size and cost of boost converter systems can be minimized by reduced voltage deviations and fast transient responses in case of large signal load transients. The key idea of the proposed ΔV/Δt-intervention control concept is to adapt the controller output to its new steady state value immediately after a load transient by prediction from known parameters. The concept is implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology and a Xilinx Spartan-6 field programmable gate array (FPGA). In a boost converter with 3.5V input voltage, 6.3V output voltage, 1.2A load, and 500 kHz switching frequency, the output voltage deviations are 2.8x smaller, scaling down the output capacitor value by the same factor. The recovery times are 2.4x shorter in case of large signal load transients with the proposed concept. The control is widely applicable, as it supports constant switching frequencies and allows for duty cycle and inductor current limitations. It also shows various advantages compared to conventional control and to selected adaptive control concepts.
This paper presents a digitally controlled boost converter IC for high output voltage and fast transient applications. Thus, it is well applicable in automotive and industrial environments. The 3V-to-6V input voltage, 6.3V output voltage, 1A boost converter IC is fabricated in a 180nm BCD technology. Digital control enables cost savings, advanced control concepts, and it is less parameter sensitive compared to common analog control. A 90 ns latency, 6-bit delay line ADC operates with a window concept, meeting high resolution requirements, e.g. in car battery applications. An output voltage live tracking is included for extending the ADC conversion window. A charge pump DAC provides high resolution, monotonicity, and short 128 ns conversion time. Further, a standard digital PI controller is enhanced by a simple but effective ΔV/Δt-intervention control. It results in 2.8x reduced output voltage deviations in case of load steps, scaling down the output capacitor value by the same factor.
Size and cost of a boost converter can be minimized by reducing the voltage overshoot and fastening the transient response in case of load transient. The presented technique improves the transient response of a current mode controlled boost converter, which usually suffers from bandwidth limitation because of its right-half-plane zero (RHPZ). The proposed technique comprises a load current estimation which works as part of a digital controller without any additional measurements. Based on the latest load estimation the controller parameters are adapted, achieving small voltage overshoot and fast transient response. The presented technique was implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology, a Xilinx Spartan-6 field programmable gate array (FPGA), and a TI-ADS8422 analog to-digital-converter (ADC). Simulation and measurements of a 4V-to-6.3V, 500mA boost converter show an improvement of 50% in voltage overshoot and response time to load transient.