Refine
Document Type
- Conference proceeding (41) (remove)
Is part of the Bibliography
- yes (41) (remove)
Institute
- Technik (41)
Publisher
- IEEE (25)
- Hochschule Ulm (6)
- Technische Universität Berlin (3)
- Technische Universität Darmstadt (2)
- Arbeitsgemeinschaft Simulation (ASIM) (1)
- ECPE (1)
- Power Sources Manufacturers Association (1)
- VDE Verlag (1)
- VDE-Verlag (1)
Bootstrap circuits are mainly used for supplying a gate driver circuit to provide the gate overdrive voltage for a high-side NMOS transistor. The required charge has to be provided by a bootstrap capacitor which is often too large for integration if an acceptable voltage dip at the capacitor has to be guaranteed. Three options of an area efficient bootstrap circuit for a high side driver with an output stage of two NMOS transistors are proposed. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and connected when the gate driver turns on. A high voltage swing at the second capacitor leads to a high charge allocation. Both bootstrap capacitors require up to 70% less area compared to a conventional bootstrap circuit. This enables compact power management systems with fewer discrete components and smaller die size. A calculation guideline for optimum bootstrap capacitor sizing is given. The circuit was manufactured in a 180nm high-voltage BiCMOS technology as part of a high-voltage gate driver. Measurements confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit including two stacked 75.8pF and 18.9pF capacitors results in a voltage dip lower than 1V. This matches well with the theory of the calculation guideline.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum conversion ratio are limited by the duty cycle of a PWM signal. In DCDC converters, a sawtooth generator is the fundamental circuit block to generate the PWM signal. The presented PWM generator is based on two parallel, fully interleaved PWM generator stages, each containing an integrator based sawtooth generator and two 3-stage highspeed comparators. A digital multiplexing of the PWM signals of each stage eliminates the dependency of the minimum on-time on the large reset times of the sawtooth ramps. A separation of the references of the PWM comparators in both stage allows to configure the PWM generator for a DCDC converter operating in fixed frequency or in constant on-time mode, which requires an operation in a wide frequency range. The PWM generator was fabricated in an 180 nm HV BiCMOS technology, as part of a DCDC converter. Measurements confirm minimum possible ontime pulses as short as 2 ns and thus allows switching frequencies of DCDC converters of >50 MHz at small duty cycle of <10%. At moderate duty cycles switching frequencies up to 100 MHz are possible.
Substrate coupling is a critical failure mechanism especially in fast-switching integrated power stages controlling high-side NMOS power FETs. The parasitic coupling across the substrate in integrated power stages at rise times of up to 500 ps and input voltages of up to 40V is investigated in this paper. The coupling has been studied for the power stage of an integrated buck converter. In particular, dedicated diverting and isolation structures against substrate coupling are analyzed by simulations and evaluated with measurements from test chips in 180nm high-voltage BiCMOS. The results are compared regarding effectiveness, area as well as implementation effort and cost. Back-side metalization shows superior characteristics with nearly 100% noise suppression. Readily available p-guard ring structures bring 75% disturbance reduction. The results are applicable to advanced and future power management solutions with fully integrated switched-mode power supplies at switching frequencies >10 MHz.
DC-DC-converters are used in many different applications. Specifying the switching frequency is the most important parameter to calculate component costs and required space. Especially automotive applications of small brushed- or brushless dc-motors and the increasing number of DC-DC-converters have high requirements on the structual space (low box volume). This is of particular importance for automotive converters for the new 48 V board net. Multiplying the frequency by two will reduce the size of the power inductor by half at a given specification for output-voltage ripple. Smaller power inductors result in reduced losses due to smaller series resistance and parasitic capacitance. Furthermore a larger switching frequency decreases the size of the DC link capacitors. The circuit will get more idealized. However, as the switching losses increase with frequency, a DC-DC-converter can only benefit from these advantages if the switching behavior can be improved.
This paper presents an optimization method to increase switching slope and switching frequency of a 3.6 kW 3-phase step-up converter by separating the design and layout process into two parts. The first part is the power stage which carries the load current. It contains the power inductance and the drain-source-channel of the power MOSFETs. The second part is the driver circuit which contains the driver ICs, the gate resistor and the gate input impedance. While the switching slope was measured to be improved by 50 % , the switching time decreased by 20 %. Hence, the switching frequency of the step-up converter could be increased from 100 kHz to 200 kHz without loss increase. By mounting the driver ICs in a piggyback configuration in close proximity to the power stage, the parasitics could be further reduced significantly and 500 kHz switching frequency could be achieved with 97.5 % efficiency.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
There is a growing need for motor drives with improved EMC in various automotive and industrial applications. An often referenced approach to reduce EME is to change the shape of the switching signal to reduce the EMI caused by the voltage and current transitions. This requires very precise gate control of the power MOSFET to achive better switching behaviour and lower EME without a major increase in switching losses. In order to find an optimal trade-off, this work utilizes a monolithic current mode gate driver with a variable output current that can be changed within 10ns. With this driver, measurements with different gate current profiles were taken. The di/dt transition was confirmed to be as important as the dv/dt transition in the power MOSFET. As a result of the improved switching behavior the emissions were reduced by up to 20dB between 7MHz and 60MHz with a switching loss that is 52% lower than with a constantly low gate current.
Galvanic isolated gate drivers require a control signal as well as energy transmission from the control side (lowside) to the driver side (high-side). An additional backward signal transmission is preferred for error signals, status information, etc. This is often realized by means of several transformers or opto-couplers. Decreasing the number of isolation elements results in lower cost and a higher degree of miniaturization. This work presents a gate driver with bidirectional signal transmission and energy transfer via one single transformer. The key concept proposed in this paper is to combine bootstrapping to deliver the main gate charge for the driven power switch with additional energy transfer via the signal transformer. This paper also presents a very efficient combination of energy transfer to two high-side supply rails with back channel amplitude modulation. This way an isolated gate driver can be implemented that allows 100% pulse-width modulation (PWM) duty cycle at low complexity and system cost. The proposed high-side driver IC with integrated power supply, modulation and demodulation circuits was manufactured in a 180nm high-voltage BiCMOS technology. Measurements confirm the concept of bidirectional signal transmission with a 1MBit/s amplitude modulation, 10/20MHz frequency modulation and a maximum power transmission of 14mW via the transformer.
In diesem Beitrag wird ein kapazitiver Low Power DC-DC Wandler mit 15 konfigurierbaren Übersetzungsverhältnissen, einem hohen Eingangsspannungsbereich von 5 V bis 20 V und einer konstanten Ausgangsspannung von 5 V vorgestellt. Bei einer Ausgangsleistung von 5 mW wird ein maximaler Wirkungsgrad von 81% erreicht. Die Implementierung erfolgt in einem 350 nm Hochvolt-CMOS-Prozess. Während es für niedrige Eingangsspannungen eine Vielzahl an Topologien und Konzepten gibt, wurden vollintegrierte SC-Wandler für höhere Eingangsspannungen (> 8 V) bisher nur wenig untersucht. Höhere Spannungen erfordern den Einsatz von Hochvolttransistoren und eine aufwändigere Ansteuerung. Um über einen weiteren Eingangsspannungsbereicht mit hoher Genauigkeit und hohem Wirkungsgrad zu wandeln, erweist sich die Topologie des rekursiven Switched-Capacitor Wandlers (RSC Wandler) als vorteilhaft. In der vorliegenden 4-Bit Implementierung ist der RSC Wandler aus N = 4 2:1 Serien-Parallel Wandler-Zellen aufgebaut. Durch verschiedene Anordnung der einzelnen Zellen können 2ᴺ -1 = 15 Wandlungsverhältnisse realisiert werden. Mittels Rekursion werden in jedem Wandlungsverhältnis alle Kapazitäten genutzt, wodurch die Stromfähigkeit und der Wirkungsgrad des Wandlers deutlich verbessert werden. Einheitliche 2:1 Wandler-Zellen ermöglichen einen modularen Aufbau des Layouts.