Refine
Document Type
- Conference proceeding (35) (remove)
Language
- English (35) (remove)
Has full text
- yes (35)
Is part of the Bibliography
- yes (35)
Institute
- Technik (35)
Publisher
A millimeter-wave power amplifier concept in an advanced silicon germanium (SiGe) BiCMOS technology is presented. The goal of the concept is to investigate the impact of physical limitations of the used heterojunction bipolar transistors (HBT) on the performance of a 77 GHz power amplifier. High current behavior, collectorbase breakdown and transistor saturation can be forced with the presented design. The power amplifier is manufactured in an advanced SiGe BiCMOS technology at Infineon Technologies AG with a maximum transit frequency fT of around 250 GHz for npn HBT’s [1]. The simulation results of the power amplifier show a saturated output power of 16 dBm at a power added efficiency of 13%. The test chip is designed for a supply voltage of 3.3 V and requires a chip size of 1.448 x 0.930 mm².
Bootstrap circuits are mainly used for supplying a gate driver circuit to provide the gate overdrive voltage for a high-side NMOS transistor. The required charge has to be provided by a bootstrap capacitor which is often too large for integration if an acceptable voltage dip at the capacitor has to be guaranteed. Three options of an area efficient bootstrap circuit for a high side driver with an output stage of two NMOS transistors are proposed. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and connected when the gate driver turns on. A high voltage swing at the second capacitor leads to a high charge allocation. Both bootstrap capacitors require up to 70% less area compared to a conventional bootstrap circuit. This enables compact power management systems with fewer discrete components and smaller die size. A calculation guideline for optimum bootstrap capacitor sizing is given. The circuit was manufactured in a 180nm high-voltage BiCMOS technology as part of a high-voltage gate driver. Measurements confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit including two stacked 75.8pF and 18.9pF capacitors results in a voltage dip lower than 1V. This matches well with the theory of the calculation guideline.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
In recent years, significant progress has been made on switched-capacitor DC-DC converters as they enable fully integrated on-chip power management. New converter topologies overcame the fixed input-to-output voltage limitation and achieved high efficiency at high power densities. SC converters are attractive to not only mobile handheld devices with small input and output voltages, but also for power conversion in IoE, industrial and automotive applications, etc. Such applications need to be capable of handling widely varying input voltages of more than 10V, which requires a large amount of conversion ratios. The goal is to achieve a fine granularity with the least number of flying capacitors. In [1] an SC converter was introduced that achieves these goals at low input voltage VIN ≤ 2.5V. [2] shows good efficiency up to VIN = 8V while its conversion ratio is restricted to ≤1/2 with a limited, non-equidistant number of conversion steps. A particular challenge arises with increasing input voltage as several loss mechanisms like parasitic bottom-plate losses and gate-charge losses of high-voltage transistors become of significant influence. High input voltages require supporting circuits like level shifters, auxiliary supply rails etc., which allocate additional area and add losses [2-5]. The combination of both increasing voltage and conversion ratios (VCR) lowers the efficiency and the achievable output power of SC converters. [3] and [5] use external capacitors to enable higher output power, especially for higher VIN. However, this is contradictory to the goal of a fully integrated power supply.
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
Size and cost of a boost converter can be minimized by reducing the voltage overshoot and fastening the transient response in case of load transient. The presented technique improves the transient response of a current mode controlled boost converter, which usually suffers from bandwidth limitation because of its right-half-plane zero (RHPZ). The proposed technique comprises a load current estimation which works as part of a digital controller without any additional measurements. Based on the latest load estimation the controller parameters are adapted, achieving small voltage overshoot and fast transient response. The presented technique was implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology, a Xilinx Spartan-6 field programmable gate array (FPGA), and a TI-ADS8422 analog to-digital-converter (ADC). Simulation and measurements of a 4V-to-6.3V, 500mA boost converter show an improvement of 50% in voltage overshoot and response time to load transient.
The efficiency impact of air-cored inductors used close to and beyond its cut-off frequency in multi-MHz converters is investigated. A method is presented to determine the converter switching frequency that causes the lowest losses in a given inductor. Influential parameters are analysed to optimize an inductor for a predefined switching frequency.