Refine
Document Type
- Conference proceeding (12)
- Patent / Standard / Guidelines (5)
- Journal article (3)
- Book chapter (1)
Is part of the Bibliography
- yes (21)
Institute
- Technik (21)
Publisher
In dieser Arbeit wird eine optimierte Bandgap-Referenz zur Erzeugung einer temperaturstabilen Spannung und eines Referenzstroms vorgestellt. Für Low-Power-Anwendungen wurde die Bandgap-Referenz, basierend auf der Brokaw-Zelle, mit minimaler Stromaufnahme und optimierter Chipfläche durch Multi-Emitter-Layout der Bipolartransistoren implementiert. Zusätzliches Merkmal ist ein verbreiteter Versorgungsspannungsbereich von 2,5 bis 5,5 V. Simulationen zeigen, dass eine stabile Ausgangsspannung von 1,218 V und ein Referenzstrom von 1,997 μA realisiert wird. Im Temperaturbereich -40 °C … 50 °C sowie dem gesamten Bereich der Versorgungsspannung beträgt die Genauigkeit der Referenzspannung ± 0,04 % mit einer Gesamtstromaufnahme zwischen 3,5 und 10 μA. Es wird eine Temperaturdrift von 2,18 ppm/K erreicht. Durch das elektronische Trimmen von Widerständen wird der Offset der Ausgangsspannung, bedingt durch Herstellungstoleranzen, auf ±3,5 mV justiert. Die Referenz wird in einer 0,18 μm BiCMOS-Technologie implementiert.
Durch schnell schaltende Leistungsendstufen werden durch kapazitive Umladeströme Störungen ins Substrat und in empfindliche Schaltungselemente eingekoppelt, die dort zur Störung der Funktion führen können. In dieser Arbeit werden Substratstrukturen zur gezielten Ableitung dieser Störungen vorgestellt und ihre Wirksamkeit mit Hilfe von Device Simulation evaluiert. Ohne Ableitstrukturen kann eine Potentialanhebung des Substrats bis zu 20 V entstehen. Die Untersuchungen belegen, dass die Potentialanhebung durch p-Typ Guard-Ringe um 75 %, durch leitende Trenches um 88 % sowie durch Rückseitenmetallisierung um nahezu 100 % reduziert werden kann.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. This leads especially at a high input voltage to a decreasing efficiency caused by switching losses. Conventional calculations are not suitable to predict the efficiency as parasitic capacitances have a significant loss contribution. This paper presents an analytical efficiency model which considers parasitic capacitances separately and calculates the power loss contribution of each capacitance to any resistive element. The proposed model is utilized for efficiency optimization of converters with switching frequencies >10MHz and input voltages up to 40V. For experimental evaluation a DCDC converter was manufactured in a 180 nm HV BiCMOS technology. The model matches a transistor level simulation and measurement results with an accuracy better than 3.5 %. The accuracy of the parasitic capacitances of the high voltage transistor determines the overall accuracy of the efficiency model. Experimental capacitor measurements can be fed into the model. Based on the model, different architectures have been studied.
A highly integrated synchronous buck converter with a predictive dead time control for input voltages >18 V with 10 MHz switching frequency is presented. A high resolution dead time of ˜125 ps allows to reduce dead time dependent losses without requiring body diode conduction to evaluate the dead time. High resolution is achieved by frequency compensated sampling of the switching node and by an 8 bit differential delay chain. Dead time parameters are derived in a comprehensive study of dead time depended losses. This way, the efficiency of fast switching DC-DC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching. High-speed circuit blocks for fast switching operation are presented including level shifter, gate driver, PWM generator. The converter has been implemented in a 180 nm high-voltage BiCMOS technology.
This article covers the design of highly integrated gate drivers and level shifters for high-speed, high power efficiency and dv/dt robustness with focus on automotive applications. With the introduction of the 48 V board net in addition to the conventional 12 V battery, there is an increasing need for fast switching integrated gate drivers in the voltage range of 50 V and above. State-of-the-art drivers are able to switch 50 V in less than 5 ns. The high-voltage electrical drive train demands for galvanic isolated and highly integrated gate drivers. A gate driver with bidirectional signal transmission with a 1 MBit/s amplitude modulation, 10/20 MHz frequency modulation and power transfer over one single transformer will be discussed. The concept of high-voltage charge storing enables an area-efficient fully integrated bootstrapping supply with 70 % less area consumption. EMC is a major concern in automotive. Gate drivers with slope control optimize EMC while maintaining good switching efficiency. A current mode gate driver, which can change its drive current within 10 ns, results in 20 dBuV lower emissions between 7 and 60 MHz and 52 % lower switching loss compared to a conventional constant current gate driver.
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
The increasing slew rate of modern power switches can increase the efficiency and reduce the size of power electronic applications. This requires a fast and robust signal transmission to the gate driver of the high-side switch. This work proposes a galvanically isolated capacitive signal transmission circuit to increase common mode transient immunity (CMTI). An additional signal path is introduced to significantly improve the transmission robustness for small duty cycles to assure a safe turn-off of the power switch. To limit the input voltage range at the comparator on the secondary side during fast high-side transitions, a clamping structure is implemented. A comparison between a conventional and the proposed signal transmission is performed using transistor level simulations. A propagation delay of about 2 ns over a wide range of voltage transients of up to 300V/ns at input voltages up to 600V is achieved.
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.