Refine
Document Type
- Conference proceeding (35)
- Journal article (8)
- Patent / Standard / Guidelines (4)
- Book chapter (1)
Language
- English (48) (remove)
Is part of the Bibliography
- yes (48)
Institute
- Technik (48)
Publisher
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
A fast transient current-mode buckboost DC-DC converter for portable devices is presented. Running at 1 MHz the converter provides stable 3 V from a 2.7 V to 4.2 V Li-Ion battery. A small voltage under-/overshoot is achieved by fast transient techniques: (1) adaptive pulse skipping (APS) and (2) adaptive compensation capacitance (ACC). The proposed converter was implemented in a 0.25 μm CMOS technology. Load transient simulations confirm the effectiveness of APS and ACC. The improvement in voltage undershoot and response time at light-to-heavy load step (100 mA to 500 mA), are 17 % and 59 %, respectively, in boost mode and 40 % and 49 %, respectively, in buck mode. Similar results are achieved at heavy-to-light load step for overshoot and response time.
A wide-bandwidth galvanically isolated current sensing circuit with an integrated Rogowski coil in 180nm CMOS is presented. Exploiting the high-frequency properties of an optimized on-chip Rogowski coil, currents can be measured up to a bandwidth of 75 MHz. The analog sensor front-end comprises a two-stage integrator, which allows a chopper frequency below signal bandwidth, resulting in 2.2 mVrms output noise. An additional integrated Hall sensor extends the measurement range towards DC.
A device including a first and second monitoring unit, the first monitoring unit detecting a first voltage potential and the second monitoring unit detecting a second voltage potential, the monitoring units comparing the first voltage potential and the second voltage potential to the value of the supply voltage and activate a control unit as a function of the comparisons, the control unit determining a switching point in time of a second power transistor, and an arrangement being present which generates current when the second power transistor is being switched on, the current changing the first voltage potential, and the control unit activates a first power transistor when the first voltage potential has the same value as the supply voltage, so that the first power transistor is de-energized.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
In a digitally controlled slope shaping system, reliable detection of both voltage and current slope is required to enable a closed-loop control for various power switches independent of system parameters. In most state-of-the-art works, this is realized by monitoring the absolute voltage and current values. Better accuracy at lower DC power loss is achieved by sensing techniques for a reliable passive detection, which is achieved through avoiding DC paths from the high voltage network into the sensing network. Using a high-speed analog-to-digital converter, the whole waveform of the transient derivative can be stored digitally and prepared for a predictive cycle-by-cycle regulation, without requiring high-precision digital differentiation algorithms. To gain an accurate representation of the voltage and current derivative waveforms, system parasitics are investigated and classified in three sections: (1) component parasitics, which are identified by s-parameter measurements and extraction of equivalent circuit models, (2) PCB design issues related to the sensing circuit, and (3) interconnections between adjacent boards.
The contribution of this paper is an optimized sensing network on the basis of the experimental study supporting fast transition slopes up to 100 V/ns and 1 A/ns and beyond, making the sensing technique attractive for slope shaping of fast switching devices like modern generation IGBTs, CoolMOSTM and SiC mosfets. Measurements of the optimized dv/dt and di/dt setups are demonstrated for a hard switched IGBT power stage.
A concept for a slope shaping gate driver IC is proposed, used to establish control over the slew rates of current and voltage during the turn-on and turn off switching transients.
It combines the high speed and linearity of a fully-integrated closed-loop analog gate driver, which is able to perform real-time regulation, with the advantages of digital control, like flexibility and parameter independency, operating in a predictive cycle-bycycle regulation. In this work, the analog gate drive integrated circuit is partitioned into functional blocks and modeled in the small-signal domain, which also includes the non-linearity of parameters. An analytical stability analysis has been performed in order to ensure full functionality of the system controlling a modern generation IGBT and a superjunction MOSFET. Major parameters of influence, such as gate resistor and summing node capacitance, are investigated to achieve stable control. The large-signal behavior, investigated by simulations of a transistor level design, verifies the correct operation of the circuit. Hence, the gate driver can be designed for robust operation.
The increasing slew rate of modern power switches can increase the efficiency and reduce the size of power electronic applications. This requires a fast and robust signal transmission to the gate driver of the high-side switch. This work proposes a galvanically isolated capacitive signal transmission circuit to increase common mode transient immunity (CMTI). An additional signal path is introduced to significantly improve the transmission robustness for small duty cycles to assure a safe turn-off of the power switch. To limit the input voltage range at the comparator on the secondary side during fast high-side transitions, a clamping structure is implemented. A comparison between a conventional and the proposed signal transmission is performed using transistor level simulations. A propagation delay of about 2 ns over a wide range of voltage transients of up to 300V/ns at input voltages up to 600V is achieved.