Refine
Document Type
- Conference proceeding (25)
- Journal article (6)
Language
- English (31)
Has full text
- yes (31)
Is part of the Bibliography
- yes (31)
Institute
- Technik (31)
Publisher
- IEEE (31) (remove)
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
A wide-bandwidth galvanically isolated current sensing circuit with an integrated Rogowski coil in 180nm CMOS is presented. Exploiting the high-frequency properties of an optimized on-chip Rogowski coil, currents can be measured up to a bandwidth of 75 MHz. The analog sensor front-end comprises a two-stage integrator, which allows a chopper frequency below signal bandwidth, resulting in 2.2 mVrms output noise. An additional integrated Hall sensor extends the measurement range towards DC.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
In a digitally controlled slope shaping system, reliable detection of both voltage and current slope is required to enable a closed-loop control for various power switches independent of system parameters. In most state-of-the-art works, this is realized by monitoring the absolute voltage and current values. Better accuracy at lower DC power loss is achieved by sensing techniques for a reliable passive detection, which is achieved through avoiding DC paths from the high voltage network into the sensing network. Using a high-speed analog-to-digital converter, the whole waveform of the transient derivative can be stored digitally and prepared for a predictive cycle-by-cycle regulation, without requiring high-precision digital differentiation algorithms. To gain an accurate representation of the voltage and current derivative waveforms, system parasitics are investigated and classified in three sections: (1) component parasitics, which are identified by s-parameter measurements and extraction of equivalent circuit models, (2) PCB design issues related to the sensing circuit, and (3) interconnections between adjacent boards.
The contribution of this paper is an optimized sensing network on the basis of the experimental study supporting fast transition slopes up to 100 V/ns and 1 A/ns and beyond, making the sensing technique attractive for slope shaping of fast switching devices like modern generation IGBTs, CoolMOSTM and SiC mosfets. Measurements of the optimized dv/dt and di/dt setups are demonstrated for a hard switched IGBT power stage.
A concept for a slope shaping gate driver IC is proposed, used to establish control over the slew rates of current and voltage during the turn-on and turn off switching transients.
It combines the high speed and linearity of a fully-integrated closed-loop analog gate driver, which is able to perform real-time regulation, with the advantages of digital control, like flexibility and parameter independency, operating in a predictive cycle-bycycle regulation. In this work, the analog gate drive integrated circuit is partitioned into functional blocks and modeled in the small-signal domain, which also includes the non-linearity of parameters. An analytical stability analysis has been performed in order to ensure full functionality of the system controlling a modern generation IGBT and a superjunction MOSFET. Major parameters of influence, such as gate resistor and summing node capacitance, are investigated to achieve stable control. The large-signal behavior, investigated by simulations of a transistor level design, verifies the correct operation of the circuit. Hence, the gate driver can be designed for robust operation.
The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the presented integrated micropower supply. Connected to the 120/230-VRMS mains, it provides a 3.3-V ac output voltage, suitable for applications such as the Internet-of Things and smart homes. The micropower supply consists of a fully integrated ac–dc and dc–dc converter with one external low-voltage surface mount device buffer capacitor, resulting in an extremely compact size. Fabricated in a low-cost 0.35-μm 700-V complimentary metal-oxide-semiconductor technology, it covers a die size of 7.7 mm². The ac–dc converter is a direct coupled, full-wave rectifier with a subsequent series regulator. The dc–dc stage is a fully integrated capacitive 4:1 converter with up to 17-V input and 47.4% peak efficiency. The power supply comprises several high-voltage control circuits including level shifters and various types of charge pumps (CPs). A source supplied CP is utilized that supports a varying switching node potential. The overall losses are discussed and optimized, including flying capacitor bottom-plate losses. The power supply achieves an output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
In recent years, significant progress has been made on switched-capacitor DC-DC converters as they enable fully integrated on-chip power management. New converter topologies overcame the fixed input-to-output voltage limitation and achieved high efficiency at high power densities. SC converters are attractive to not only mobile handheld devices with small input and output voltages, but also for power conversion in IoE, industrial and automotive applications, etc. Such applications need to be capable of handling widely varying input voltages of more than 10V, which requires a large amount of conversion ratios. The goal is to achieve a fine granularity with the least number of flying capacitors. In [1] an SC converter was introduced that achieves these goals at low input voltage VIN ≤ 2.5V. [2] shows good efficiency up to VIN = 8V while its conversion ratio is restricted to ≤1/2 with a limited, non-equidistant number of conversion steps. A particular challenge arises with increasing input voltage as several loss mechanisms like parasitic bottom-plate losses and gate-charge losses of high-voltage transistors become of significant influence. High input voltages require supporting circuits like level shifters, auxiliary supply rails etc., which allocate additional area and add losses [2-5]. The combination of both increasing voltage and conversion ratios (VCR) lowers the efficiency and the achievable output power of SC converters. [3] and [5] use external capacitors to enable higher output power, especially for higher VIN. However, this is contradictory to the goal of a fully integrated power supply.
The level shifter and the floating gate supply for high-side transistors are a major challenge in high-voltage DCDC converters. This paper presents a high speed and power-efficient level shifter for voltages of up to 50V, suitable for both PMOS and NMOS power FETs. A switching node falling edge detection allows both, a sensitive and safe signal detection. This enables a robust operation during steep dv / dt transitions and a power consumption as low as 4.1 pJ per switching cycle, which is a reduction of more than 40% compared to prior art. An active clamping circuit prevents common mode displacement currents into the high-side supply. The level shifter is implemented in a 180nm BiCMOS technology. Measurements confirm a 50V 120MHz high-speed operation of the level shifter with a rising / falling propagation delay of 1.45 ns / 1.3 ns, respectively. The dv / dt robustness has been confirmed by measurements for transitions up to 6V/ ns.
Boost converters suffer from a bandwidth limitation caused by the right-half plane zero (RHPZ), which occurs in the control-to-output transfer function. In contrast, there are many applications that require superior dynamic behavior. Further, size and cost of boost converter systems can be minimized by reduced voltage deviations and fast transient responses in case of large signal load transients. The key idea of the proposed ΔV/Δt-intervention control concept is to adapt the controller output to its new steady state value immediately after a load transient by prediction from known parameters. The concept is implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology and a Xilinx Spartan-6 field programmable gate array (FPGA). In a boost converter with 3.5V input voltage, 6.3V output voltage, 1.2A load, and 500 kHz switching frequency, the output voltage deviations are 2.8x smaller, scaling down the output capacitor value by the same factor. The recovery times are 2.4x shorter in case of large signal load transients with the proposed concept. The control is widely applicable, as it supports constant switching frequencies and allows for duty cycle and inductor current limitations. It also shows various advantages compared to conventional control and to selected adaptive control concepts.