Refine
Document Type
Is part of the Bibliography
- yes (15)
Institute
- Technik (15)
Publisher
- IEEE (10)
- Copernicus GmbH (1)
- Hochschule Ulm (1)
A highly integrated synchronous buck converter with a predictive dead time control for input voltages >18 V with 10 MHz switching frequency is presented. A high resolution dead time of ˜125 ps allows to reduce dead time dependent losses without requiring body diode conduction to evaluate the dead time. High resolution is achieved by frequency compensated sampling of the switching node and by an 8 bit differential delay chain. Dead time parameters are derived in a comprehensive study of dead time depended losses. This way, the efficiency of fast switching DC-DC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching. High-speed circuit blocks for fast switching operation are presented including level shifter, gate driver, PWM generator. The converter has been implemented in a 180 nm high-voltage BiCMOS technology.
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
Size and cost of a boost converter can be minimized by reducing the voltage overshoot and fastening the transient response in case of load transient. The presented technique improves the transient response of a current mode controlled boost converter, which usually suffers from bandwidth limitation because of its right-half-plane zero (RHPZ). The proposed technique comprises a load current estimation which works as part of a digital controller without any additional measurements. Based on the latest load estimation the controller parameters are adapted, achieving small voltage overshoot and fast transient response. The presented technique was implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology, a Xilinx Spartan-6 field programmable gate array (FPGA), and a TI-ADS8422 analog to-digital-converter (ADC). Simulation and measurements of a 4V-to-6.3V, 500mA boost converter show an improvement of 50% in voltage overshoot and response time to load transient.
Switched-mode power supplies (SMPS) convert an input DC-voltage into a higher or lower output voltage. In automotive, analog control is mostly used in order to keep the required output voltages constant and resistant to disturbances. The design of robust analog control for SMPS faces parameter variations of integrated and external passive components. Using digital control, parameter variations can be eliminated and the required area for the integrated circuit can be reduced at the same time.
Digital control design bears challenges like the prevention of limit cycle oscillations and controller wind-up. This paper reviews how to prevent these effects. Digital control loops introduce new sources for dead times in the control loop, for example the latency of the analog-to-digitalconverter (ADC). Dead times have negative influence on the stability of the control loop, because they lead to phase delays. Consequently, low latency is one of the key requirements for analog-to-digital converters in digitally controlled SMPS.
Exploiting the example of a 500 kHz-buck converter with a crossover frequency of 70 kHz, this paper shows that the 5 μs-latency of a 16-analog-to-digital-converter leads to a reduction in phase margin of 126°. The latency is less critical for boost converters because of their inherent lower crossover frequencies.
Finally, the paper shows a comparison between analog and digital control of SMPS with regard to chip area and test costs.
Die Spannungsversorgung elektronischer Steuergeräte im Automotive-Bereich wird zunehmend durch Schaltregler sichergestellt. Der SEPIC (Single Ended Primary Inductance Converter) besitzt die Eigenschaft, eine Spannung aufwärts wie auch abwärts wandeln zu können und könnte somit klassische Buck- und Boost-Wandler ablösen. Dieser Beitrag untersucht den SEPIC hinsichtlich Eignung für Automotive-Anwendungen. Dazu wurde eine Groß- sowie Kleinsignalanalyse am Wandler durchgeführt, mit geeigneten Simulationsmodellen nachgebildet und Messungen gegenüber gestellt. Der SEPIC zeigt als Hauptvorteile:
1. einen verzugsfreien Übergang zwischen Buck-/Boost Betrieb, 2. geringe Eingangswelligkeit, 3.DC-Kurzschlussfestigkeit. Auch hinsichtlich Wirkungsgrad und EMV-Verhalten stellt der SEPIC eine interessante Alternative dar. Der zwischen Ein- und Ausgang liegende Kondensator wird dauerhaft von einem Strom durchflossen, auf Basis der Effektivströme wird das damit verbundene Ausfallrisiko diskutiert.