Refine
Document Type
- Conference proceeding (3)
- Journal article (1)
Language
- English (4)
Has full text
- yes (4)
Is part of the Bibliography
- yes (4)
Institute
- Technik (4)
Publisher
- IEEE (3)
- VDE-Verlag (1)
For area reasons, NMOS transistors are preferred over PMOS for the pull-up path in gate drivers. Bootstrapping has to ensure sufficient NMOS gate overdrive. Especially in high-current gate drivers with large transistors, the bootstrap capacitor is too large for integration. This paper proposes three options of fully integrated bootstrap circuits. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and ensures high charge allocation when the driver turns on. A capacitor sizing guideline and the overall driver implementation including a suitable charge pump for permanent driver activation is provided. A linear regulator is used for bootstrap supply and it also compensates the voltage drop of the bootstrap diode. Measurements from a testchip in 180 nm high-voltage BiCMOS confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit with two stacked 75.8 pF and 18.9 pF capacitors results in an expected voltage dip of lower than 1 V. Both bootstrap capacitors require 70% less area compared to a conventional bootstrap circuit. Besides drivers, the proposed bootstrap can also be directly applied to power stages to achieve fully integrated switched mode power supplies or class-D output stages.
Galvanic isolated gate drivers require a control signal as well as energy transmission from the control side (lowside) to the driver side (high-side). An additional backward signal transmission is preferred for error signals, status information, etc. This is often realized by means of several transformers or opto-couplers. Decreasing the number of isolation elements results in lower cost and a higher degree of miniaturization. This work presents a gate driver with bidirectional signal transmission and energy transfer via one single transformer. The key concept proposed in this paper is to combine bootstrapping to deliver the main gate charge for the driven power switch with additional energy transfer via the signal transformer. This paper also presents a very efficient combination of energy transfer to two high-side supply rails with back channel amplitude modulation. This way an isolated gate driver can be implemented that allows 100% pulse-width modulation (PWM) duty cycle at low complexity and system cost. The proposed high-side driver IC with integrated power supply, modulation and demodulation circuits was manufactured in a 180nm high-voltage BiCMOS technology. Measurements confirm the concept of bidirectional signal transmission with a 1MBit/s amplitude modulation, 10/20MHz frequency modulation and a maximum power transmission of 14mW via the transformer.
DC-DC-converters are used in many different applications. Specifying the switching frequency is the most important parameter to calculate component costs and required space. Especially automotive applications of small brushed- or brushless dc-motors and the increasing number of DC-DC-converters have high requirements on the structual space (low box volume). This is of particular importance for automotive converters for the new 48 V board net. Multiplying the frequency by two will reduce the size of the power inductor by half at a given specification for output-voltage ripple. Smaller power inductors result in reduced losses due to smaller series resistance and parasitic capacitance. Furthermore a larger switching frequency decreases the size of the DC link capacitors. The circuit will get more idealized. However, as the switching losses increase with frequency, a DC-DC-converter can only benefit from these advantages if the switching behavior can be improved.
This paper presents an optimization method to increase switching slope and switching frequency of a 3.6 kW 3-phase step-up converter by separating the design and layout process into two parts. The first part is the power stage which carries the load current. It contains the power inductance and the drain-source-channel of the power MOSFETs. The second part is the driver circuit which contains the driver ICs, the gate resistor and the gate input impedance. While the switching slope was measured to be improved by 50 % , the switching time decreased by 20 %. Hence, the switching frequency of the step-up converter could be increased from 100 kHz to 200 kHz without loss increase. By mounting the driver ICs in a piggyback configuration in close proximity to the power stage, the parasitics could be further reduced significantly and 500 kHz switching frequency could be achieved with 97.5 % efficiency.
Bootstrap circuits are mainly used for supplying a gate driver circuit to provide the gate overdrive voltage for a high-side NMOS transistor. The required charge has to be provided by a bootstrap capacitor which is often too large for integration if an acceptable voltage dip at the capacitor has to be guaranteed. Three options of an area efficient bootstrap circuit for a high side driver with an output stage of two NMOS transistors are proposed. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and connected when the gate driver turns on. A high voltage swing at the second capacitor leads to a high charge allocation. Both bootstrap capacitors require up to 70% less area compared to a conventional bootstrap circuit. This enables compact power management systems with fewer discrete components and smaller die size. A calculation guideline for optimum bootstrap capacitor sizing is given. The circuit was manufactured in a 180nm high-voltage BiCMOS technology as part of a high-voltage gate driver. Measurements confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit including two stacked 75.8pF and 18.9pF capacitors results in a voltage dip lower than 1V. This matches well with the theory of the calculation guideline.
