621 Angewandte Physik
Refine
Document Type
Has full text
- yes (7)
Is part of the Bibliography
- yes (7)
Institute
- Technik (7)
Publisher
- IEEE (5)
- Hochschule Ulm (2)
Substrate coupling is a critical failure mechanism especially in fast-switching integrated power stages controlling high-side NMOS power FETs. The parasitic coupling across the substrate in integrated power stages at rise times of up to 500 ps and input voltages of up to 40V is investigated in this paper. The coupling has been studied for the power stage of an integrated buck converter. In particular, dedicated diverting and isolation structures against substrate coupling are analyzed by simulations and evaluated with measurements from test chips in 180nm high-voltage BiCMOS. The results are compared regarding effectiveness, area as well as implementation effort and cost. Back-side metalization shows superior characteristics with nearly 100% noise suppression. Readily available p-guard ring structures bring 75% disturbance reduction. The results are applicable to advanced and future power management solutions with fully integrated switched-mode power supplies at switching frequencies >10 MHz.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum conversion ratio are limited by the duty cycle of a PWM signal. In DCDC converters, a sawtooth generator is the fundamental circuit block to generate the PWM signal. The presented PWM generator is based on two parallel, fully interleaved PWM generator stages, each containing an integrator based sawtooth generator and two 3-stage highspeed comparators. A digital multiplexing of the PWM signals of each stage eliminates the dependency of the minimum on-time on the large reset times of the sawtooth ramps. A separation of the references of the PWM comparators in both stage allows to configure the PWM generator for a DCDC converter operating in fixed frequency or in constant on-time mode, which requires an operation in a wide frequency range. The PWM generator was fabricated in an 180 nm HV BiCMOS technology, as part of a DCDC converter. Measurements confirm minimum possible ontime pulses as short as 2 ns and thus allows switching frequencies of DCDC converters of >50 MHz at small duty cycle of <10%. At moderate duty cycles switching frequencies up to 100 MHz are possible.
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
In dieser Arbeit wird eine optimierte Bandgap-Referenz zur Erzeugung einer temperaturstabilen Spannung und eines Referenzstroms vorgestellt. Für Low-Power-Anwendungen wurde die Bandgap-Referenz, basierend auf der Brokaw-Zelle, mit minimaler Stromaufnahme und optimierter Chipfläche durch Multi-Emitter-Layout der Bipolartransistoren implementiert. Zusätzliches Merkmal ist ein verbreiteter Versorgungsspannungsbereich von 2,5 bis 5,5 V. Simulationen zeigen, dass eine stabile Ausgangsspannung von 1,218 V und ein Referenzstrom von 1,997 μA realisiert wird. Im Temperaturbereich -40 °C … 50 °C sowie dem gesamten Bereich der Versorgungsspannung beträgt die Genauigkeit der Referenzspannung ± 0,04 % mit einer Gesamtstromaufnahme zwischen 3,5 und 10 μA. Es wird eine Temperaturdrift von 2,18 ppm/K erreicht. Durch das elektronische Trimmen von Widerständen wird der Offset der Ausgangsspannung, bedingt durch Herstellungstoleranzen, auf ±3,5 mV justiert. Die Referenz wird in einer 0,18 μm BiCMOS-Technologie implementiert.
Durch schnell schaltende Leistungsendstufen werden durch kapazitive Umladeströme Störungen ins Substrat und in empfindliche Schaltungselemente eingekoppelt, die dort zur Störung der Funktion führen können. In dieser Arbeit werden Substratstrukturen zur gezielten Ableitung dieser Störungen vorgestellt und ihre Wirksamkeit mit Hilfe von Device Simulation evaluiert. Ohne Ableitstrukturen kann eine Potentialanhebung des Substrats bis zu 20 V entstehen. Die Untersuchungen belegen, dass die Potentialanhebung durch p-Typ Guard-Ringe um 75 %, durch leitende Trenches um 88 % sowie durch Rückseitenmetallisierung um nahezu 100 % reduziert werden kann.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.