Refine
Document Type
- Conference proceeding (120) (remove)
Language
- English (120)
Has full text
- yes (120)
Is part of the Bibliography
- yes (120)
Institute
- Technik (120) (remove)
Publisher
- IEEE (120) (remove)
Boost converters suffer from a bandwidth limitation caused by the right-half plane zero (RHPZ), which occurs in the control-to-output transfer function. In contrast, there are many applications that require superior dynamic behavior. Further, size and cost of boost converter systems can be minimized by reduced voltage deviations and fast transient responses in case of large signal load transients. The key idea of the proposed ΔV/Δt-intervention control concept is to adapt the controller output to its new steady state value immediately after a load transient by prediction from known parameters. The concept is implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology and a Xilinx Spartan-6 field programmable gate array (FPGA). In a boost converter with 3.5V input voltage, 6.3V output voltage, 1.2A load, and 500 kHz switching frequency, the output voltage deviations are 2.8x smaller, scaling down the output capacitor value by the same factor. The recovery times are 2.4x shorter in case of large signal load transients with the proposed concept. The control is widely applicable, as it supports constant switching frequencies and allows for duty cycle and inductor current limitations. It also shows various advantages compared to conventional control and to selected adaptive control concepts.
This article proposes several modified quasi Z-source dc/dc boost converters. These can achieve soft-switching by using a clamp-switch network comprised of an active switch and a diode in parallel with a capacitor connected across one of the inductors of the Z-source network. In this way, ringing at the transistor switching node is mitigated, and the voltage at the turn-on of the transistor is reduced. Even a zero voltage switching (ZVS) of the main transistor is possible if the capacitor in the clamp-switch network is adequately chosen. The proposed circuit structure and operating mode are described and validated through simulations and measurements on a low-power prototype.
Verification of an active time constant tuning technique for continuous-time delta-sigma modulators
(2022)
In this work we present a technique to compensate the effects of R-C / g m -C time-constant (TC) errors due to process variation in continuous-time delta-sigma modulators. Local TC error compensation factors are shifted around in the modulator loop to positions where they can be implemented efficiently with finely tunable circuit structures, such as current-steering digital-to-analog converters (DAC). We apply our technique to a third-order, single-bit, low-pass continuous-time delta-sigma modulator in cascaded integrator feedback structure, implemented in a 0.35-μm CMOS process. A tuning scheme for the reference currents of the feedback DACs is derived as a function of the individual TC errors and verified by circuit simulations. We confirm the tuning technique experimentally on the fabricated circuit over a TC parameter variation range of ±20%. Stable modulator operation is achieved for all parameter sets. The measured performances satisfy the expectations from our theoretical calculations and circuit-level simulations.
The experimental characterization of the thermal impedance Zth of large power MOSFETs is commonly done by measuring the junction temperature Tj in the cooling phase after the device has been heated, preferably to a high junction temperature for increased accuracy. However, turning off a large heating current (as required by modern MOSFETs with low on-state resistances) takes some time because of parasitic inductances in the measurement system. Thus, most setups do not allow the characterization of the junction temperature in the time range below several tens of μs.
In this paper, an optimized measurement setup is presented which allows accurate Tj characterization already 3 μs after turn-off of heating. With this, it becomes possible to experimentally investigate the influence of thermal capacitances close to the active region of the device. Measurement results will be presented for advanced power MOSFETs with very large heating currents up to 220 A. Three bonding variants are investigated and the observed differences will be explained.
In this work, a comparison between different brushless harmonic-excited wound-rotor synchronous machines is performed. The general idea of all topologies is the elimination of the slip rings and auxiliary windings by using the already existing stator and rotor winding for field excitation. This is achieved by injecting a harmonic airgap field with the help of power electronics. This harmonic field does not interact with the fundamental field, it just transfers the excitation power across the airgap. Alternative methods with varying number of phases, different pole-pair combinations, and winding layouts are covered and compared with a detailed Finite-Element-parameterized model. Parasitic effects due to saturation and coupling between the harmonic and main windings are considered.
Most Question-answering (QA) systems rely on training data to reach their optimal performance. However, acquiring training data for supervised systems is both time-consuming and resource-intensive. To address this, in this paper, we propose TFCSG, an unsupervised similar question retrieval approach that leverages pre-trained language models and multi-task learning. Firstly, topic keywords in question sentences are extracted sequentially based on a latent topic-filtering algorithm to construct unsupervised training corpus data. Then, the multi-task learning method is used to build the question retrieval model. There are three tasks designed. The first is a short sentence contrastive learning task. The second is the question sentence and its corresponding topic sequence similarity judgment task. The third is using question sentences to generate their corresponding topic sequence task. The three tasks are used to train the language model in parallel. Finally, similar questions are obtained by calculating the cosine similarity between sentence vectors. The comparison experiment on public question datasets that TFCSG outperforms the comparative unsupervised baseline method. And there is no need for manual marking, which greatly saves human resources.
Virtual prototyping of integrated mixed-signal smart-sensor systems requires high-performance co-simulation of analog frontend circuitry with complex digital controller hardware and embedded real-time software. We use SystemC/TLM 2.0 in combination with a cycle-count accurate temporal decoupling approach to simulate digital components and firmware code execution at high speed while preserving clock cycle accuracy and, thus, real-time behavior at time quantum boundaries. Optimal time quanta ensuring real-time capability can be calculated and set automatically during simulation if the simulation engine has access to exact timing information about upcoming communication events. These methods fail in case of non-deterministic, asynchronous events resulting in a possibly invalid simulation result. In this paper, we propose an extension of this method to the case of asynchronous events generated by blackbox sources from which a-priori event timing information is not available, such as coupled analog simulators or hardware in the loop. Additional event processing latency and/or rollback effort caused by temporal decoupling is minimized by calculating optimal time quanta dynamically in a SystemC model using a linear prediction scheme. For an example smart-sensor system model, we show that quasi- periodic events that trigger activities in temporally decoupled processes are handled accurately after the predictor has settled.
When a bonding wire becomes too hot, it fuses and fails. The ohmic heat that is generated in the wire can be partially dissipated to a mold package. For this cooling effect the thermal contact between wire and package is an important parameter. Because this parameter can degrade over lifetime, the fusing of a bonding wire can also occur as a long-term effect. Another important factor is the thermal power generated in the vicinity of the bond pads. Nowadays, the reliability of bond wires relies on robust dimensioning based on estimations. Smaller package sizes increase the need for better predictive methods.
The Bond Calculator, a new thermo-electrical simulation tool, is able to predict the temperature profiles along bond wires of arbitrary dimensions in dependence on the applied arbitrary transient current profile, the mold surrounding the wire, and the thermal contact between wire and mold.
In this paper we closely investigated the spatial temperature profiles along different bond wires in air in order to make a first step towards the experimental verification of the simulation model. We are using infrared microscopy in order to measure the thermal radiation generated along the bond wire. This is easier to perform quantitatively in air than in the mold package, because of the non-negligible absorbance of the mold material in the infrared wavelength region.
This paper evaluates experimentally the susceptibility of IT-networks under influences and the threats of HPEM (High Power Electromagnetic) and IEMI (Intentional Electromagnetic Interferences). As HPEM source a PBG 5 (Pulse Burst Generator) adapted to a TEM (Transversal Electromagnetic) Horn type antenna and a 90 cm IRA (Impulse Radiating Antenna) type antenna is used. Different network cable types and categories with different lengths are used. The immunity of the IT network is examined and the breakdown failure rate of the system is defined for a PRF (Pulse Repetition Frequency) of 500 s-1 in duration of 10 seconds. Series of measurements were carried out and disturbances of keyboards, mouse, switches, distortions on monitors and failures of the IT network and, even crash of PCs were observed. It is shown amongst other that by increasing the pulse repetition rate or frequency, generic test IT-networks are more susceptible to interference. Obtained results provide another view of the susceptibility analysis of modern generic IT-networks against UWB-Threats.
Substrate coupling is a critical failure mechanism especially in fast-switching integrated power stages controlling high-side NMOS power FETs. The parasitic coupling across the substrate in integrated power stages at rise times of up to 500 ps and input voltages of up to 40V is investigated in this paper. The coupling has been studied for the power stage of an integrated buck converter. In particular, dedicated diverting and isolation structures against substrate coupling are analyzed by simulations and evaluated with measurements from test chips in 180nm high-voltage BiCMOS. The results are compared regarding effectiveness, area as well as implementation effort and cost. Back-side metalization shows superior characteristics with nearly 100% noise suppression. Readily available p-guard ring structures bring 75% disturbance reduction. The results are applicable to advanced and future power management solutions with fully integrated switched-mode power supplies at switching frequencies >10 MHz.
Micro grids often consist of energy generators, storages and consumers with controllers which are not prepared for their integration into communication networks for energy systems. In this paper it will be presented, how standards from the field of energy automation can be applied in such controllers. The data for communication interfaces can be structured according to the IEC 61850- or the VHPREADY standard. It is investigated which requirements must be supported to implement such data models within the controllers. For the transmission of the data we propose the OPC UA protocol, which supports extensive security measures and which is today available for nearly all modern types of controllers and computers.
We present a compact battery charger topology for weight and cost sensitive applications with an average output current of 9A targeted for 36V batteries commonly found in electric bicycles. Instead of using a conventional boost converter with large DC-link capacitors, we accomplish PFC-functionality by shaping the charging current into a sin²-shape. In addition, a novel control scheme without input-current sensing is introduced. A-priori knowledge is used to implement a feed-forward control in combination with a closed-loop output current control to maintain the target current. The use of a full-bridge/half bridge LLC converter enables operation in a wide input-voltage range.
A fully featured prototype has been built with a peak output power of 1050W. An average output power of 400W was measured, resulting in a power density of 1.8 kW/dm³. At 9A charging current, a power factor of 0.96 was measured and the efficiency exceeds 93% on average with passive rectification.
The impact of pulse charging has been evaluated on a 400Wh battery which was charged with the proposed converter as well as CC-CV-charging for reference. Both charging schemes show similar battery surface temperatures.
Energy efficient electric control of drives is more and more important for electric mobility and manufacturing industries. Online dynamic optimization of induction machines is challenging due to the computational complexity involved and the variable power losses during dynamic operation of induction machines. This paper proposes a simple technique for sub-optimal online loss optimization using rotor flux linkage templates for energy efficient dynamic operation of induction machines. Such a rotor flux linkage template is given by a rotor flux linkage trajectory which is optimal for a specific scenario. This template is calculated in an offline optimization process. For a specific scenario during real time operation the rotor flux linkage is calculated by appropriately scaling the given template.
In this work we investigate the behavior of MIS- and Schottky-gate AlGaN/GaN HEMTs under high-power pulsestress. A special setup capable of applying pulses of constant power is used to evaluate the electro-thermal response in different operating points. For both types of devices, the time to failure was found to decrease with increasing drain-source voltage. Overall, the Schottky-gate device displays a higher pulse robustness. The pulse withstand time of the MIS-gate device is limited by the occurrence of a thermal instability at approximately 240°C while the Schottky-gate device displays a rapid increase of the gate leakage current prior to failure. The mechanism responsible for this gate current is further investigated by static and transient temperature measurements and yielded activation energies of 0.6 eV and 0.84 eV.
The loss contribution of a 2.3kW synchronous GaN-HEMT boost converter for an input voltage of 250V and an output voltage of 500V was analyzed. A simulation model which consists of two parts is introduced. First, a physics-based model is used to determine the switching losses. Then, a system simulation is applied to calculate the losses of the specific elements. This approach allows a fast and accurate system evaluation as required for further system optimization.
In this work, a hard- and a zero-voltage turn-on switching converter are compared. Measurements were performed to verify the simulation model, showing a good agreement. A peak efficiency of 99% was achieved for an output power of 1.4kW. Even with an output power above 400W, it was possible to obtain a system efficiency exceeding 98 %.
We present the results of an extensive characterization of the performance and stability of a third-order continuous-time delta-sigma modulator with active coefficient error compensation. Using our previously published coefficient tuning technique, process variation induced R-C time-constant (TC) errors in the forward signal path can be compensated indirectly using continuously tunable DACs in the feedback path. To validate our technique experimentally with a range of real TC variations, we designed a modulator with discretely configurable integration capacitor arrays in a 0.35-μm CMOS process. We configured the capacitors of the fabricated device for a range of total TC variations from -28.4 % to +19.3 % and measured the signal-to-noise ratio (SNR) as a function of the input amplitude before and after compensating the variations electrically using the feedback DACs. The results show that our tuning technique is capable of restoring the desired nominal modulator performance over the entire parameter variation range, including the system’s nominal maximum stable amplitude (MSA).
While digital IC design is highly automated, analog circuits are still handcrafted in a time-consuming, manual fashion today. This paper introduces a novel Parameterized Circuit Description Scheme (PCDS) for the development of procedural analog schematic generators as parameterized circuits. Circuit designers themselves can use PCDS to create circuit automatisms which capture valuable expert knowledge, offer full topological flexibility, and enhance the re-use of well-established topologies. The generic PCDS concept has been successfully implemented and employed to create parameterized circuits for a broad range of use cases. The achieved results demonstrate the efficiency of our PCDS approach and the potential of parameterized circuits to increase automation in circuit design, also to benefit physical design by promoting the common schematic-driven-layout flow, and to enhance the applicability of circuit synthesis approaches.
Nowadays, the demand for a MEMS development/design kit (MDK) is even more in focus than ever before. In order to achieve a high quality and cost effectiveness in the development process for automotive and consumer applications, an advanced design flow for the MEMS (micro electro mechanical systems) element is urgently required. In this paper, such a development methodology and flow for parasitic extraction of active semiconductor devices is presented. The methodology considers geometrical extraction and links the electrically active pn junctions to SPICE standard library models and subsequently extracts the netlist. An example for a typical pressure sensor is presented and discussed. Finally, the results of the parasitic extraction are compared with fabricated devices in terms of accuracy and capability.
In a digitally controlled slope shaping system, reliable detection of both voltage and current slope is required to enable a closed-loop control for various power switches independent of system parameters. In most state-of-the-art works, this is realized by monitoring the absolute voltage and current values. Better accuracy at lower DC power loss is achieved by sensing techniques for a reliable passive detection, which is achieved through avoiding DC paths from the high voltage network into the sensing network. Using a high-speed analog-to-digital converter, the whole waveform of the transient derivative can be stored digitally and prepared for a predictive cycle-by-cycle regulation, without requiring high-precision digital differentiation algorithms. To gain an accurate representation of the voltage and current derivative waveforms, system parasitics are investigated and classified in three sections: (1) component parasitics, which are identified by s-parameter measurements and extraction of equivalent circuit models, (2) PCB design issues related to the sensing circuit, and (3) interconnections between adjacent boards.
The contribution of this paper is an optimized sensing network on the basis of the experimental study supporting fast transition slopes up to 100 V/ns and 1 A/ns and beyond, making the sensing technique attractive for slope shaping of fast switching devices like modern generation IGBTs, CoolMOSTM and SiC mosfets. Measurements of the optimized dv/dt and di/dt setups are demonstrated for a hard switched IGBT power stage.