Refine
Year of publication
- 2015 (31) (remove)
Document Type
- Conference proceeding (29)
- Journal article (2)
Language
- English (31)
Has full text
- yes (31)
Is part of the Bibliography
- yes (31)
Institute
- Technik (22)
- Informatik (5)
- ESB Business School (3)
- Texoversum (1)
Publisher
- IEEE (31) (remove)
Substrate coupling is a critical failure mechanism especially in fast-switching integrated power stages controlling high-side NMOS power FETs. The parasitic coupling across the substrate in integrated power stages at rise times of up to 500 ps and input voltages of up to 40V is investigated in this paper. The coupling has been studied for the power stage of an integrated buck converter. In particular, dedicated diverting and isolation structures against substrate coupling are analyzed by simulations and evaluated with measurements from test chips in 180nm high-voltage BiCMOS. The results are compared regarding effectiveness, area as well as implementation effort and cost. Back-side metalization shows superior characteristics with nearly 100% noise suppression. Readily available p-guard ring structures bring 75% disturbance reduction. The results are applicable to advanced and future power management solutions with fully integrated switched-mode power supplies at switching frequencies >10 MHz.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum conversion ratio are limited by the duty cycle of a PWM signal. In DCDC converters, a sawtooth generator is the fundamental circuit block to generate the PWM signal. The presented PWM generator is based on two parallel, fully interleaved PWM generator stages, each containing an integrator based sawtooth generator and two 3-stage highspeed comparators. A digital multiplexing of the PWM signals of each stage eliminates the dependency of the minimum on-time on the large reset times of the sawtooth ramps. A separation of the references of the PWM comparators in both stage allows to configure the PWM generator for a DCDC converter operating in fixed frequency or in constant on-time mode, which requires an operation in a wide frequency range. The PWM generator was fabricated in an 180 nm HV BiCMOS technology, as part of a DCDC converter. Measurements confirm minimum possible ontime pulses as short as 2 ns and thus allows switching frequencies of DCDC converters of >50 MHz at small duty cycle of <10%. At moderate duty cycles switching frequencies up to 100 MHz are possible.
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.
Galvanic isolated gate drivers require a control signal as well as energy transmission from the control side (lowside) to the driver side (high-side). An additional backward signal transmission is preferred for error signals, status information, etc. This is often realized by means of several transformers or opto-couplers. Decreasing the number of isolation elements results in lower cost and a higher degree of miniaturization. This work presents a gate driver with bidirectional signal transmission and energy transfer via one single transformer. The key concept proposed in this paper is to combine bootstrapping to deliver the main gate charge for the driven power switch with additional energy transfer via the signal transformer. This paper also presents a very efficient combination of energy transfer to two high-side supply rails with back channel amplitude modulation. This way an isolated gate driver can be implemented that allows 100% pulse-width modulation (PWM) duty cycle at low complexity and system cost. The proposed high-side driver IC with integrated power supply, modulation and demodulation circuits was manufactured in a 180nm high-voltage BiCMOS technology. Measurements confirm the concept of bidirectional signal transmission with a 1MBit/s amplitude modulation, 10/20MHz frequency modulation and a maximum power transmission of 14mW via the transformer.
There is a growing need for motor drives with improved EMC in various automotive and industrial applications. An often referenced approach to reduce EME is to change the shape of the switching signal to reduce the EMI caused by the voltage and current transitions. This requires very precise gate control of the power MOSFET to achive better switching behaviour and lower EME without a major increase in switching losses. In order to find an optimal trade-off, this work utilizes a monolithic current mode gate driver with a variable output current that can be changed within 10ns. With this driver, measurements with different gate current profiles were taken. The di/dt transition was confirmed to be as important as the dv/dt transition in the power MOSFET. As a result of the improved switching behavior the emissions were reduced by up to 20dB between 7MHz and 60MHz with a switching loss that is 52% lower than with a constantly low gate current.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
In this paper a double hogger used in woodworking machines is considered. The machining tools are driven by induction machines operated by standard inverters. During production the load of these motors changes periodically between low load and high load at a given speed. This paper investigates the reduction of power losses in such an application using an appropriate energy efficient control strategy for the induction machines.
A generic, knowledge-based method for automatic topology selection of analog circuits in a predefined analog reuse library is presented in this paper on the OTA (Operational Transconductance Amplifier) example. Analog circuits of a given circuit class are classified in a topology tree, where each node represents a specific topology. Child nodes evolve from their parent nodes by an enhancement of the parent node’s topological structure. Topology selection is performed by a depth first-search in the topology tree starting at the root node, thus checking topologies of increasing complexity. The decisions at each node are based on solving equations or – if this is not possible – on simulations. The search ends at the first (and thus the simplest) topology which can meet the specification after an adequate circuit sizing. The advantages of the generic, tree based topology selection method presented in this paper are shown in comparison to a pool selection method and to heuristic approaches. The selection is based on an accomplished chip investigation.
When a bonding wire becomes too hot, it fuses and fails. The ohmic heat that is generated in the wire can be partially dissipated to a mold package. For this cooling effect the thermal contact between wire and package is an important parameter. Because this parameter can degrade over lifetime, the fusing of a bonding wire can also occur as a long-term effect. Another important factor is the thermal power generated in the vicinity of the bond pads. Nowadays, the reliability of bond wires relies on robust dimensioning based on estimations. Smaller package sizes increase the need for better predictive methods.
The Bond Calculator, a new thermo-electrical simulation tool, is able to predict the temperature profiles along bond wires of arbitrary dimensions in dependence on the applied arbitrary transient current profile, the mold surrounding the wire, and the thermal contact between wire and mold.
In this paper we closely investigated the spatial temperature profiles along different bond wires in air in order to make a first step towards the experimental verification of the simulation model. We are using infrared microscopy in order to measure the thermal radiation generated along the bond wire. This is easier to perform quantitatively in air than in the mold package, because of the non-negligible absorbance of the mold material in the infrared wavelength region.
In this paper, we propose a novel fitting method that uses local image features to fit a 3D morphable face model to 2D images. To overcome the obstacle of optimising a cost function that contains a non-differentiable feature extraction operator, we use a learning-based cascaded regression method that learns the gradient direction from data. The method allows to simultaneously solve for shape and pose parameters. Our method is thoroughly evaluated on morphable model generated data and first results on real data are presented. Compared to traditional fitting methods, which use simple raw features like pixel colour or edge maps, local features have been shown to be much more robust against variations in imaging conditions. Our approach is unique in that we are the first to use local features to fit a 3D morphable model. Because of the speed of our method, it is applicable for realtime applications. Our cascaded regression framework is available as an open source library at github.com/patrikhuber/ superviseddescent.