Refine
Document Type
- Journal article (25) (remove)
Is part of the Bibliography
- yes (25)
Institute
- Texoversum (25)
Publisher
- dfv Mediengruppe (10)
- Deutscher Fachverlag (4)
- Elsevier (3)
- IBP, Internat. Business Press Publisher (2)
- American Chemical Society (1)
- MDPI (1)
- Royal Society of Chemistry (1)
- SAGE Publications Ltd (1)
- Springer (1)
- Verlag Textilplus AG (1)
Thin, flat textile roofing offers negligible heat insulation. In warm areas, such roofing membranes are therefore equipped with metallized surfaces to reflect solar heat radiation, thus reducing the warming inside a textile building. Heat reflection effects achieved by metallic coatings are always accompanied by shading effects as the metals are non-transparent for visible light (VIS). Transparent conductive oxides (TCOs) are transparent for VIS and are able to reflect heat radiation in the infrared. TCOs are, e.g., widely used in the display industry. To achieve the perfect coatings needed for electronic devices, these are commonly applied using costly vacuum processes at high temperatures. Vacuum processes, on account of the high costs involved and high processing temperatures, are obstructive for an application involving textiles. Accepting that heat-reflecting textile membranes demand less perfect coatings, a wet chemical approach has been followed here when producing transparent heat-reflecting coatings. Commercially available TCOs were employed as colloidal dispersions or nanopowders to prepare sol-gel-based coating systems. Such coatings were applied to textile membranes as used for architectural textiles using simple coating techniques and at moderate curing temperatures not exceeding 130 °C. The coatings achieved about 90% transmission in the VIS spectrum and reduced near-infrared transmission (at about 2.5 µm) to nearly zero while reflecting up to 25% of that radiation. Up to 35% reflection has been realized in the far infrared, and emissivity values down to ε = 0.5777 have been measured.
Der pH-Wert der menschlichen Haut liegt nicht im neutralen Bereich, sondern ist mit Werten von 3,5-6 – je nach Körperstelle – leicht Sauer. Das bietet der Kommensalen Hautflora einen geeigneten Lebensraum, wirkt jedoch abtötend auf einige pathogene Mikroorganismen und inaktivierend auf einige Viren. Dieser Säureschutzmantel der Haut stellt somit eine erste äußere Schutzschicht vor dem Befall von Krankheitserregern dar. Ein entsprechender Oberflächen-pH-Wert auf Textilien kann dazu beitragen, die Übertragung von Krankheitserregern durch die Kleidung von Mitarbeitern im Gesundheitswesen zu minimieren und gleichzeitig keinen negativen Einfluss auf die hauteigene Flora auszuüben. Zudem kann die Besiedlung von z.B. Bettwäsche durch pathogene Mikroorganismen vermindert werden. Einen positiven Einfluss kann dies zudem auf die bakterienassoziierte Geruchsbildung auf Funktionskleidung haben.
Der pH-Wert der menschlichen Haut liegt nicht im neutralen Bereich, sondern ist mit Werten von 3,5-6 – je nach Körperstelle – leicht Sauer. Das bietet der Kommensalen Hautflora einen geeigneten Lebensraum, wirkt jedoch abtötend auf einige pathogene Mikroorganismen und inaktivierend auf einige Viren. Dieser Säureschutzmantel der Haut stellt somit eine erste äußere Schutzschicht vor dem Befall von Krankheitserregern dar. Ein entsprechender Oberflächen-pH-Wert auf Textilien kann dazu beitragen, die Übertragung von Krankheitserregern durch die Kleidung von Mitarbeitern im Gesundheitswesen zu minimieren und gleichzeitig keinen negativen Einfluss auf die hauteigene Flora auszuüben. Zudem kann die Besiedlung von z.B. Bettwäsche durch pathogene Mikroorganismen vermindert werden. Einen positiven Einfluss kann dies zudem auf die bakterienassoziierte Geruchsbildung auf Funktionskleidung haben.
Im IGF-Projekt Nr. 19617 N wurden stickstoff- und phosphorsubstituierte Alkoxysilane hergestellt und ihre flammhemmenden Eigenschaften für Textilien untersucht. Die Synthesen erfolgten nach unterschiedlichen Strategien wie der Klick-Chemie und der nukleophilen Substitution kommerziell erhältlicher Organophosphorverbindungen mit aminobasierten Trialkoxysilanen und/oder Cyanurchlorid. Diese neuartigen, halogen- und aldehydfreien Flammschutzmittel wurden auf Stoffe aus Baumwolle (BW), Polyethylenterephthalat (PET), Polyamid (PA), sowie Mischgeweben daraus mit der industriell etablierten Pad-Dry-Cure-Technik und mittels Sol-Gel-Verfahren aufgetragen. Die flammhemmenden Eigenschaften wurden mit den Prüfverfahren nach EN ISO 15025 (Schutzkleidung – Schutz gegen Hitze und Flammprüfverfahren für begrenzte Flammenausbreitung= bewertet. Eine gute Schwerentflammbarkeit der hybriden organisch-anorganischen Materialien wurde bei einer geringen Menge von 3-5 Gew.% auf Baumwollgeweben erreicht. Darüber hinaus konnten die Wasserlöslichkeit und die Waschbeständigkeit durch die an das Phosphoratom gebundenen funktionellen Gruppen und durch die Optimierung der Härtungstemperatur kontrolliert werden. Insgesamt zeigte das Forschungsprojekt, dass N-P-Silane sehr gute permanente Flammschutzmittel für Textilien sind.
The wet chemical deposition of solution processed transparent conducting oxides (TCO) provides an alternative low cost and economical deposition technique to realize large-areas of conducting films. Since the price for the most common TCO Indium Tin Oxide rises enormously, Aluminum Zinc Oxide (AZO) as alternative TCO reaches more and more interest. The optoelectronical properties of nanoparticle coatings strongly depend beneath the porosity of the coating on the shape and size of the used particles. By using bigger or rod-shaped particles it is possible to minimize the amount of grain boundaries resulting in an improvement of the electrical properties, whereas particles bigger than 100 nm should not be used if highly transparent coatings are necessary as these big particles scatter the visible light and lower the transmittance of the coatings. In this work we present a simple method to synthesize AZO particles with different shape and size, but comparable electronical properties. We use a simple, well reproducible polyol method for synthesis and influence the shape and size of the particles by adding different amounts of water to the precursor solution. We can show that the addition of aluminum as dopant strongly hinders the crystal growth but the addition of water counteracts this, so that both, spherical and rod-shaped particles can be obtained.
In the IGF project No. 19617 N, nitrogen and phosphorous substituted alkoxysilanes were prepared and their ability to inhibit fire growth and spread for fabrics was explored. To this end, a series of flame retardants were synthesized using different strategies including click chemistry and nucleophilic substitution of commercial organophosphorus compounds with amino-based trialkoxysilanes and/or cyanuric chloride. The new halogen-free and aldehyde-free flame retardants were applied to different fabrics such as cotton (CO), polyethylene terephthalate (PET), polyamide (PA) and their blends using the well-known pad-dry-cure technique and sol-gel method. The flame-retarding efficiencies were evaluated by EN ISO 15025 test methods (protective clothing-protection against heat and flame method of test for limited flame spread). Good flame retardancy of the hybrid organic-inorganic materials was achieved with the addition of as small amount as 3-5 wt.% for cotton fabrics. Moreover, the water solubility and the washing resistance could be controlled through the functional groups attached to the phosphor atom or through the optimization of the curing temperature. Overall, the research project demonstrated that N-P-silanes are very good permanent flame retardants for textiles.
Using the damage area as a quantification method for the Martindale test is a promising method to compare textile finishes without the need to test to full destruction. In addition, it could be shown that the results of Martindale tests performed with different pressure loads can be scaled to identical functional shape. If these results can be verified, this method would be a simplification of abrasive testing for different application areas.
Es wird eine Möglichkeit zur Quantifizierung der Schädigung von Geweben bei der Martindale-Flachscheuerung vorgestellt, die eine interessante Möglichkeit darstellt, vergleichende Untersuchungen durchzuführen, auch wenn die Gewebe nicht bis zu einem Fadenbruch gescheuert werden. Die Untersuchungen deuten außerdem eine Skalierbarkeit der Scheuerversuche bei unterschiedlichen Anpressdrücken an. Sollte sich diese Beobachtung in weiteren Untersuchungen bestätigen, würde dies eine grundlegende Vereinfachung der Scheuerprüfung für verschiedene Anwendungen bedeuten.
Im Zuge von REACH wurden gängige hocheffektive halogenierte Flammschutzmittel verboten, da diese unter dem Verdach stehen, kanzerogen, mutagen und teratogen zu sein. Zur Zeit fehlen entsprechende Alternativen. Daher werden am DTNW neue umweltfreundliche und halogenfreie Flammschutzmittel auf der Basis von Phosphor- und Stickstoffverbindungen entwickelt, um einen entsprechenden Flammschutz zu gewährleisten. Neue Möglichkeiten werden im Rahmen dieses Artikels vorgestellt.
Schweißerschutzkleidung muss unterschiedlichen Anforderungen genügen. Sie muss u.a. flammfest sein, den Schweißer vor Metallspritzern schützen, die beim Schweißen entstehen, und auch einen Schutz vor UV-Licht sicherstellen, das im Schweißbogen entsteht. Besonders der Schutz vor Metallspritzern wird durch das Flächengewicht der Textilien bestimmt. Der entsprechende Schutzfaktor wird durch Tropfen flüssigen Eisens bestimmt, die auf ein Gewebe fallen. Dabei gilt: je höher das Flächengewicht, desto höher der Schutz vor Schweißspritzern. Jedoch gilt auch: je höher das Flächengewicht, desto schlechter ist der Tragekomfort und desto wärmender ist die Kleidung und damit die körperliche Belastung des Trägers. Durch die Applikation von Nanopartikeln ist es möglich, das benötigte Flächengewicht der Kleidung zu reduzieren.
Schweißerschutzkleidung muss unterschiedlichen Anforderungen genügen. Sie muss u.a. flammfest sein, den Schweißer vor Metallspritzern schützen, die beim Schweißen entstehen, und auch einen Schutz vor UV-Licht sicherstellen, das im Schweißbogen entsteht. Besonders der Schutz vor Metallspritzern wird durch das Flächengewicht der Textilien bestimmt. Der entsprechende Schutzfaktor wird durch Tropfen flüssigen Eisens bestimmt, die auf ein Gewebe fallen. Dabei gilt: je höher das Flächengewicht, desto höher der Schutz vor Schweißspritzern. Jedoch gilt auch: je höher das Flächengewicht, desto schlechter ist der Tragekomfort und desto wärmender ist die Kleidung und damit die körperliche Belastung des Trägers. Durch die Applikation von Nanopartikeln ist es möglich, das benötigte Flächengewicht der Kleidung zu reduzieren.
Die Anforderungen an Textilien unterscheiden sich je nach Anwendungsbereich stark, wobei es häufig nicht bei nur einer benötigten Funktionalität bleibt. Im Bereich der Funktions- oder Schutzkleidung bzw. PSA ist es z.B. nötig, die Träger der Kleidung vor UV-Strahlung zu schützen. Gleichzeitig bieten hier selbstreinigende Effekte gewisse Vorteile. Zudem kann eine antimikrobielle Wirkung im Bereich der Funktionskleidung die Bildung unangenehmer Gerüche vermindern, sowie im Bereich der PSA – besonders im Gesundheitswesen – zur Unterbrechung von Infektionsketten beitragen. Eine Möglichkeit, diese 3 gewünschten Funktionen in nur einem Ausrüstungsschritt zu erzielen, ist die Immobilisierung von Titandioxid (TiO2). Dieses wird aber aufgrund einer REACH-Listung kritisch für die Anwendung im textilen Sektor gesehen. Nachteilig ist zudem, dass es seine Wirkung nur unter UV-Einstrahlung entfaltet und damit nicht für den Innenbereich geeignet ist. Alternativ können Photokatalysatoren wie dotierte Zinkoxide (ZnO) verwendet werden, die auch durch Einstrahlung im Bereich des sichtbaren Lichts eine katalytische Aktivität aufweisen, die zur Abtötung von Mikroorganismen und zum Abbau organischer Verschmutzungen führen kann.
Protective welding clothing must meet various requirements. Among other things, it must be flame-resistant, protect against splashes of metal or sparks and also ensure protection against radiant heat and UV light caused by exposure to the welding arc. The protection against molten metal splashes is directly related to the fabric weight per unit area of the protective welding clothing and the level of protection is normally determined by the number of molten metal droplets that fall on the fabric. The higher the weight per unit area, the greater the protection against welding spatter. However, increasing the fabric weight per unit area also leads to psychologically uncomfortable wearing and thus increasing the physical strain on the wearer. The required basis weight per unit area of protective welding clothing can be reduced by applying nanoparticles as a protective layer while preserving other indispensable properties.
Protective welding clothing must meet various requirements. Among other things, it must be flame-resistant, protect against splashes of metal or sparks and also ensure protection against radiant heat and UV light caused by exposure to the welding arc. The protection against molten metal splashes is directly related to the fabric weight per unit area of the protective welding clothing and the level of protection is normally determined by the number of molten metal droplets that fall on the fabric. The higher the weight per unit area, the greater the protection against welding spatter. However, increasing the fabric weight per unit area also leads to psychologically uncomfortable wearing and thus increasing the physical strain on the wearer. The required basis weight per unit area of protective welding clothing can be reduced by applying nanoparticles as a protective layer while preserving other indispensable properties.
Indium tin oxide (ITO) particle coatings are known for high transparency in the visible, good conductive properties and near-infrared absorption. These properties depend on ITO particle's stiochiometric composition, defects and size. Here we present a method to gradually change ITO particle's optical properties by a simple and controlled laser irradiation process. The defined irradiation process and controlled energy dose input allows one to engineer the absorption and transsmission of coatings made from these particles. We investigate the role of the surrounding solvent, influence of laser fluence and the specific energy dose targeting modification of the ITO particle's morphology and chemistry by stepwise laser irradiation in a free liquid jet. TEM, SEM, EDX, XPS, XRD and Raman are used to elucidate the structural, morphological and chemical changes of the laser-induced ITO particles. On the basis of these results the observed modification of the optical properties is tentatively attributed to chemical changes, e.g. laser-induced defects or partial reduction.
Flame-retardant finishing of cotton fabrics using DOPO functionalized alkoxy- and amido alkoxysilane
(2023)
In the present study, DOPO-based alkoxysilane (DOPO-ETES) and amido alkoxysilane (DOPO-AmdPTES) were synthesized by one-step and without by-products as halogen-free flame retardants. The flame retardants were applied on cotton fabric utilizing sol–gel method and pad-dry-cure finishing process. The flame retardancy, the thermal stability and the combustion ehaviour of treated cotton were evaluated by surface and bottom edge ignition flame test (according to EN ISO 15025), thermogravimetric analysis (TGA) and micro-scale combustion calorimeter (MCC). Unlike CO/DOPO-ETES sample, cotton treated with DOPO-AmdPTES nanosols exhibits self-extinguishing ehaviour with high char residue, an improvement of the LOI value and a significant reduction of the PHRR, HRC and THR compared to pristine cotton. Cotton finished with DOPO-AmdPTES reveals a semi-durability after ten laundering cycles keeping the flame-retardant properties unchanged. According to the results obtained from TGA-FTIR, Py-GC/MS and XPS, the major activity of flame retardant occurs in the condensed phase via catalytic induced char formation as physical barrier along with the activity in the gas phase derived mainly from the dilution effect. The early degradation of CO/DOPO-AmdPTES compared to CO/DOPO-ETES, triggered by the cleavage of the weak bond between P and C=O, as the DFT study indicated, provides the beneficial effect of this flame retardant on the fire resistance of cellulose.
The sol-gel approach offers a new class of flame retardants with a high potential for textile applications. Pure inorganic sol-gel systems do, however, typically not provide an effect sufficient for a sel-fextinguishing behavior on its own. We therefore employed compounds with nitrogen and phosphorous containing groups. Especially the combination of compounds with both elements, using the synergism, is promising for the aim to find well-applicable, environmental friendly, halogen-free flame retardants. In our approach, the sol-gel network ensured on the one hand the link to the textile as nonflammable binder. On the other hand, the sol-gel-based networks modified with functional groups containing nitrogen groups provided flame retardancy. In this way, a flame retardant finishing for textiles could be obtained by simple finishing techniques as, e.g., padding. Besides a characterization with various flame tests (e.g., according to EN ISO 15025 e protective clothing), we used a combination of cone calorimetry, thermogravimetry coupled with infrared spectroscopy analysis and scanning electron microscopy to analyze the mechanism of flame retardancy. Thus, we could show that the main mechanism is based on the formation of a protection layer. This work provides a model system for sol-gel-based flame retardants and has the potential to show the principle feasibility of the sol-gel approach in flame retardancy of textiles. It therefore lays the groundwork for tailoring sol-gel layers from newly synthesized sol-gel precursors containing nitrogen and phosphorous groups.
Several ionic liquids are excellent solvents for cellulose. Starting from that finishing of PET fabrics with cellulose dissolved in ionic liquids like 1-ethyl 3-methyl imidazolium acetate, diethylphosphate and chloride, or the chloride of butyl-methyl imidazolium has been investigated. Finishing has been carried out from solutions of different concentrations, using microcrystalline cellulose or cotton and by employing different cross-linkers. Viscosity of solutions has been investigated for different ionic liquids,concentrations, cellulose sources, linkers and temperatures. Since ionic liquids exhibit no vapor pressure,simple pad-dry-cure processes are excluded. Before drying the ionic liquid has to be removed by a rinsing step. Accordingly rinsing with fresh ionic liquid followed by water or the direct rinsing with waterhave been tested. The amount of cellulose deposited has been investigated by gravimetry, zinc chlorideiodine test as well as reactive dyeing. Results concerning wettability, water up-take, surface resistance,wear-resistance or washing stability are presented.
The requirements for textiles differ greatly depending on the area of application, whereby it often does not remain with only one required functionality. For example, in the field of functional clothing or protective clothing/PPE, it is necessary to protect the textile’s wearers from UV radiation. At the same time, self-cleaning effects offer certain advantages in that field. In addition, an antimicrobial effect in functional clothing can reduce the formation of unpleasant odors, and in PPE – especially in the healthcare sector – can contribute to the interruption of the chain of infection. One way to achieve these 3 desired functions in just one finishing step is to immobilize titanium dioxide (TiO2). However, TiO2 is viewed critically for application in the textile sector due to a REACH listing. Another disadvantage is that it only takes effect under UV radiation and is therefore not suitable for indoor use. Alternatively, photocatalysts such as doped zinc oxides (ZnO) can be used, which also exhibit catalytic activity through activation by visible light, which can lead to the killing of microorganisms and the degradation of organic soiling.
Cleanable bag filter : comparisons of different testing methods of ageing of filter materials
(2019)
Cleanable bag filters are used to separate dust and other airborne particulate systems. Due to typical process conditions, they are subject to thermal, chemical and mechanical stress during use. The main objective of the IGF project no. 18307 "Investigation of the chemical and thermal degradation of cleanable filter media and improvement of their resistance by surface modification", was the development of a valid test method which can reproduce degradation caused by high temperatures and aggressive chemical atmospheres in a practice-oriented but time-saving manner. Within the IGF project, 2 accelerated ageing methods were applied, both of which have the decisive advantage of investigating damage in the gas phase. Many resistances of filter materials are otherwise carried out by immersing the materials in a mostly liquid damage medium at a defined temperature. These resistances are difficult to transfer ageing in the gas phase.
Energy consumption by air-conditioning is expansive and leads to the emission of millions of tons of CO2 every year. A promising approach to circumvent this problem is the reflection of solar radiation: Rooms that would not heat up by irradiation will not need to be cooled down. Especially, transparent conductive metal oxides exhibit high infrared (IR) reflectivity and are commonly applied as low-emissivity coatings (low-e coatings). Indium tin oxide (ITO) coatings are the state-of-the-art application, though indium is a rare and expensive resource. This work demonstrates that aluminum-doped zinc oxide (AZO) can be a suitable alternative to ITO for IR-reflection applications. AZO synthesized here exhibits better emissivity to be used as roofing membrane coatings for buildings in comparison to commercially available ITO coatings. AZO particles forming the reflective coating are generated via solvothermal synthesis routes and obtain high conductivity and IR reflectivity without the need of any further post-thermal treatment. Different synthesis parameters were studied, and their effects on both conductive and optical properties of the AZO nanoparticles were evaluated. To this end, a series of characterization methods, especially 27Al-nuclear magnetic resonance spectroscopy (27Al-NMR) analysis, have been conducted for a deeper insight into the particles’ structure to understand the differences in conductivity and optical properties. The optimized AZO nanoparticles were coated on flexible transparent textile-based roofing membranes and tested as low-e coatings. The membranes demonstrated higher thermal reflectance compared with commercial ITO materials with an emissivity value lowered by 16%.
The pH value of the human skin is not in the neutral range but is slightly acidic with values of – depending on the body part – 3.5 to 6. This provides a suitable habitat for the commensal skin floral but has a killing effect on some pathogenic micro-organisms and an inactivating effect on some viruses. This protective acid mantle of the skin thus represents a first external protective layer against infestation by pathogens. An appropriate surface pH on textiles can help to minimize the transmission of pathogens through the clothing of healthcare workers while at the same time not exerting a negative influence on the skin’s own flora. In addition, the colonization of e.g. bed linen by pathogenic microorganisms can be reduced. This can also have a positive influence on bacteria-associated odor formation on functional clothing.
The pH value of the human skin is not in the neutral range but is slightly acidic with values of – depending on the body part – 3.5 to 6. This provides a suitable habitat for the commensal skin floral but has a killing effect on some pathogenic micro-organisms and an inactivating effect on some viruses. This protective acid mantle of the skin thus represents a first external protective layer against infestation by pathogens. An appropriate surface pH on textiles can help to minimize the transmission of pathogens through the clothing of healthcare workers while at the same time not exerting a negative influence on the skin’s own flora. In addition, the colonization of e.g. bed linen by pathogenic microorganisms can be reduced. This can also have a positive influence on bacteria-associated odor formation on functional clothing.
Abreinigbare Schlauchfilter kommen zur Abscheidung von Stäuben sowie staubförmigen Substanzen zum Einsatz. Aufgrund typischer Prozessbedingungen unterliegen sie während ihres Einsatzes thermischer, chemischer und mechanischer Beanspruchung. Das IGF-Projekt Nr. 18307 "Untersuchung der chemischen und thermischen Degradation von abreinigbaren Filtermedien und Verbesserung deren Beständigkeit durch Oberflächenmodifikation" hat mehrere Prüfmethoden verglichen.
Three established test methods employed for evaluating the abrasion or wear resistance of textile materials were compared to gain deeper insight into the specific damaging mechanisms to better understand a possible comparability of the results of the different tests. The knowledge of these mechanisms is necessary for a systematic development of finishing agents improving the wear resistance of textiles. Martindale, Schopper, and Einlehner tests were used to analyze two different fabrics made of natural (cotton) or synthetic (polyethylene terephthalate) fibers, respectively. Samples were investigated by digital microscopy and scanning electron microscopy to visualize the damage. Damage symptoms are compared and discussed with respect to differences in the damaging mechanisms.