Refine
Document Type
- Conference proceeding (30)
- Journal article (5)
Language
- English (35)
Has full text
- yes (35)
Is part of the Bibliography
- yes (35)
Institute
- Technik (35)
Publisher
- IEEE (35) (remove)
A TLP system with a very low characteristic impedance of 1.5 Ω and a selectable pulse length from 0.5 to 6 μs is presented. It covers the entire operation region of many power semiconductors up to 700 V and 400 A. Ist applicability is demonstrated by determining the Output characteristics for two Cool MOS devices up to destruction.
Gallium nitride high electron mobility transistors (GaN-HEMTs) have low capacitances and can achieve low switching losses in applications where hard turn-on is required. Low switching losses imply a fast switching; consequently, fast voltage and current transients occur. However, these transients can be limited by package and layout parasitics even for highly optimized systems. Furthermore, a fast switching requires a fast charging of the input capacitance, hence a high gate current.
In this paper, the switching speed limitations of GaN-HEMTs due to the common source inductance and the gate driver supply voltage are discussed. The turn-on behavior of a GaN-HEMT is simulated and the impact of the parasitics and the gate driver supply voltage on the switching losses is described in detail. Furthermore, measurements are performed with an optimized layout for a drain-source voltage of 500 V and a drain-source current up to 60 A.
Modern power semiconductor devices have low capacitances and can therefore achieve very fast switching transients under hard-switching conditions. However, these transients are often limited by parasitic elements, especially by the source inductance and the parasitic capacitances of the power semiconductor. These limitations cannot be compensated by conventional gate drivers. To overcome this, a novel gate driver approach for power semiconductors was developed. It uses a transformer which accelerates the switching by transferring energy from the source path to the gate path.
Experimental results of the novel gate driver approach show a turn-on energy reduction of 78% (from 80 μJ down to 17 μJ) with a drain-source voltage of 500V and a drain current of 60 A. Furthermore, the efficiency improvement is demonstrated for a hard-switching boost converter. For a switching frequency of 750 kHz with an input voltage of 230V and an output voltage of 400V, it was possible to extend the output power range by 35%(from 2.3kW to 3.1 kW), due to the reduction of the turn-on losses, therefore lowering the junction temperature of the GaN-HEMT.
The experimental characterization of the thermal impedance Zth of large power MOSFETs is commonly done by measuring the junction temperature Tj in the cooling phase after the device has been heated, preferably to a high junction temperature for increased accuracy. However, turning off a large heating current (as required by modern MOSFETs with low on-state resistances) takes some time because of parasitic inductances in the measurement system. Thus, most setups do not allow the characterization of the junction temperature in the time range below several tens of μs.
In this paper, an optimized measurement setup is presented which allows accurate Tj characterization already 3 μs after turn-off of heating. With this, it becomes possible to experimentally investigate the influence of thermal capacitances close to the active region of the device. Measurement results will be presented for advanced power MOSFETs with very large heating currents up to 220 A. Three bonding variants are investigated and the observed differences will be explained.
The loss contribution of a 2.3kW synchronous GaN-HEMT boost converter for an input voltage of 250V and an output voltage of 500V was analyzed. A simulation model which consists of two parts is introduced. First, a physics-based model is used to determine the switching losses. Then, a system simulation is applied to calculate the losses of the specific elements. This approach allows a fast and accurate system evaluation as required for further system optimization.
In this work, a hard- and a zero-voltage turn-on switching converter are compared. Measurements were performed to verify the simulation model, showing a good agreement. A peak efficiency of 99% was achieved for an output power of 1.4kW. Even with an output power above 400W, it was possible to obtain a system efficiency exceeding 98 %.
This paper presents a compact 3 kW bidirectional GaN-HEMT DC/DC converter for 360V to 400-500 V. A very high efficiency has been reached by applying a zero voltage turn-on in conjunction with a negative gate-source voltage, even though normally-off HEMTs are used. Further improvements were achieved by adapting the switching frequency to the load current and output voltage, as will be explained by means of the loss contribution of the specific elements for a constant and an adaptive switching frequency. Measurements have shown a high converter efficiency exceeding 99% over a wide output power range of up to 3 kW.
A gate driver approach is presented for the reduction of turn-on losses in hard switching applications. A significant turn-on loss reduction of up to 55% has been observed for SiCMOSFETs. The gate driver approach uses a transformer which couples energy from the power path back into the gate path during switching events, providing increased gate driver current and thereby faster switching speed.
The gate driver approach was tested on a boost converter running at a switching frequency up to 300 kHz. With an input voltage of 300V and an output voltage of 600V, it was possible to reduce the converter losses by 8% at full load. Moreover, the output power range could be extended by 23% (from 2.75kW to 3.4 kW) due to the reduction of the turn-on losses.
Many GaN power transistors contain a PN junction between gate and the channel region close to the source. In order to maintain the on-state, current must continuously be supplied to the junction. Therefore, the commonly recommended approach uses a gate bias voltage of 12V to compensate the Miller current through a boost circuit. For the same purpose, a novel gate driving method based on an inductive feed forward has been presented. With this, stable turn-on can be achieved even for a bias voltage of only 5V. The effectiveness of this concept is demonstrated by double pulse measurements, switching currents up to 27A and a voltage of 400V. For both approaches a compact design with low source inductance is characterized. In addition to the significant reduction of the gate bias voltage and peak gate current, the new approach reduces the switching losses for load currents >23 A.
Improved inductive feed-forward for fast turn-on of power semiconductors during hard switching
(2019)
A transformer is used to increase the gate voltage during turn-on, thus reducing the necessary bias voltage of the gate driver. Counteracting the voltage dependency of the gate capacitance of high-voltage power devices, faster transitions are possible. The additional transformer only slighly increases the over-voltage during turn-off.
Novel design for a coreless printed circuit board transformer realizing high bandwidth and coupling
(2019)
Rogowski coils offer galvanic isolation and can measure alternating currents with a high bandwidth. Coreless printed circuit board (PCB) transformers have been used as an alternative to limit the additional stray inductance if a Rogowski coil can not be attached to the circuit. A new PCB transformer layout is proposed to reduce cost, decrease additional stray inductance, increase the bandwidth of current measurements and simplify the integration into existing designs.
This paper investigates the electrothermal stability and the predominant defect mechanism of a Schottky gate AlGaN/GaN HEMT. Calibrated 3-D electrothermal simulations are performed using a simple semiempirical dc model, which is verified against high-temperature measurements up to 440°C. To determine the thermal limits of the safe operating area, measurements up to destruction are conducted at different operating points. The predominant failure mechanism is identified to be hot-spot formation and subsequent thermal runaway, induced by large drain–gate leakage currents that occur at high temperatures. The simulation results and the high temperature measurements confirm the observed failure patterns.
Advanced power semiconductors such as DMOS transistors are key components of modern power electronic systems. Recent discrete and integrated DMOS technologies have very low area-specific on-state resistances so that devices with small sizes can be chosen. However, their power dissipation can sometimes be large, for example in fault conditions, causing the device temperature to rise significantly. This can lead to excessive temperatures, reduced lifetime, and possibly even thermal runaway and subsequent destruction. Therefore, it is required to ensure already in the design phase that the temperature always remains in an acceptable range. This paper will show how self-heating in DMOS transistors can be experimentally determined with high accuracy. Further, it will be discussed how numerical electrothermal simulations can be carried out efficiently, allowing the accurate assessment of self-heating within a few minutes. The presented approach has been successfully verified experimentally for device temperatures exceeding 500 ◦C up to the onset of thermal runaway.
DMOS transistors in integrated power technologies are often subject to significant self-heating and thus high temperatures, which can lead to device failure and reduced lifetime. Hence, it must be ensured that the device temperature does not rise too much. For this, the influence of the on-chip metallization must be taken into account because of the good thermal conductivity and significant thermal capacitance of the metal layers on top of the active DMOS area. In this paper, test structures with different metal layers and vias configurations are presented that can be used to determine the influence of the onchip metallization on the temperature caused by self-heating. It will be shown how accurate results can be obtained to determine even the influence of small changes in the metallization. The measurement results are discussed and explained, showing how on-chip metallization helps to lower the device temperature. This is further supported by numerical simulations. The obtained insights are valuable for technology optimization, but are also useful for calibration of temperature simulators.
Large power semiconductors are complex structures, their metallization usually containing many thousands of contacts or vias. Because of this, detailed FEM simulations of the whole device are nowadays not possible because of excessive simulation time.
This paper introduces a simulation approach which allows quick identification of critical regions with respect to lifetime by a simplified simulation. For this, the complex layers are replaced by a much simpler equivalent layer, allowing a simulation of the whole device even including its package. In a second step, precise simulations taking all details of the structure into account are carried out, but only for the critical regions of interest. Thus, this approach gives detailed results where required with consideration of the whole structure including packaging. Further, the simulation time requirements are very moderate.
Influence of metallization layout on aging detector lifetime under cyclic thermo-mechanical stress
(2016)
The influence of the layout on early warning detectors in BCD technologies for metallization failure under cyclic thermo-mechanical stress was investigated. Different LDMOS transistors, with narrow or wide metal fingers and with or without embedded detectors, were used. The test structures were repeatedly stressed by pronounced self-heating until failure (a short circuit) was detected. The results show that the layout of the on-chip metallization has a large impact on the lifetime. A significant influence of the detectors on the lifetime was also observed, in our case causing a reduction of more than a factor of two, but only for the test structure with narrow metal fingers. The experimental results are explained by an efficient numerical thermo mechanical simulation approach, giving detailed insights into the strain distribution in the metal system. These results are important for aging detector design and, morever, for LDMOS on-chip metal layout in general.
Integrated power semiconductors are often used for applications with cyclic on-chip power dissipation. This leads to repetitive self-heating and thermo-mechanical stress, causing fatigue on the on-chip metallization and possibly destruction by short circuits. Because of this, an accurate simulation of the thermo-mechanical stress is needed already during the design phase to ensure that lifetime requirements are met. However, a detailed thermo mechanical simulation of the device, including the on-chip metallization is prohibitively time-consuming due to its complex structure, typically consisting of many thin metal lines with thousands of vias. This paper introduces a two-step approach as a solution for this problem. First, a simplified but fast simulation is performed to identify the device parts with the highest stress. After, precise simulations are carried out only for them. The applicability of this method is verified experimentally for LDMOS transistors with different metal configurations. The measured lifetimes and failure locations correlate well with the simulations. Moreover, a strong influence of the layout of the on-chip metallization lifetime was observed. This could also be explained with the simulation
method.
In this work, a brushless, harmonic-excited wound-rotor synchronous machine is investigated which utilizes special stator and rotor windings. The windings magnetically decouple the fundamental torque-producing field from the harmonic field required for the inductive power transfer to the field coil. In contrast to conventional harmonic-excited synchronous machines, the whole winding is utilized for both torque production and harmonic excitation such that no additional copper for auxiliary windings is needed. Different rotor topologies using rotating power electronic components are investigated and their efficiencies have been compared based on Finite-Element calculation and circuit analysis.
A novel brushless excitation concept for synchronous machines with a rotating power converter is proposed in this paper. The concept does not need an auxiliary winding or any other modification to the machine structure apart from an inverter with a DC link capacitor and a controller on the rotor. The power required for the rotor excitation is provided by injecting harmonics into the stator winding. Thus, a voltage in the field coil is induced. The rotor inverter is controlled such that the alternating current charges the DC link capacitor. At the same time the inverter supplies the DC field current to the field coil. The excitation concept is first developed in theory, then presented using an analytical model and FEA, and lastly investigated with a prelimininary experimental setup.
In this work design rules for a novel brushless excitation system for externally excited synchronous machines are discussed. The concept replaces slip rings with a fullbridge active rectifier and a controller mounted on the rotor. An AC signal induced from the stator is used to charge the rotor DC link. The DC current for the rotor excitation is provided from this DC link source. Finite element analysis of an existing machine is used to analyze the practicability of the excitation system.
In this work, a comparison between different brushless harmonic-excited wound-rotor synchronous machines is performed. The general idea of all topologies is the elimination of the slip rings and auxiliary windings by using the already existing stator and rotor winding for field excitation. This is achieved by injecting a harmonic airgap field with the help of power electronics. This harmonic field does not interact with the fundamental field, it just transfers the excitation power across the airgap. Alternative methods with varying number of phases, different pole-pair combinations, and winding layouts are covered and compared with a detailed Finite-Element-parameterized model. Parasitic effects due to saturation and coupling between the harmonic and main windings are considered.