Refine
Document Type
- Conference proceeding (30) (remove)
Language
- English (30)
Has full text
- yes (30)
Is part of the Bibliography
- yes (30)
Institute
- Technik (30)
Publisher
- IEEE (30) (remove)
Advanced power semiconductors such as DMOS transistors are key components of modern power electronic systems. Recent discrete and integrated DMOS technologies have very low area-specific on-state resistances so that devices with small sizes can be chosen. However, their power dissipation can sometimes be large, for example in fault conditions, causing the device temperature to rise significantly. This can lead to excessive temperatures, reduced lifetime, and possibly even thermal runaway and subsequent destruction. Therefore, it is required to ensure already in the design phase that the temperature always remains in an acceptable range. This paper will show how self-heating in DMOS transistors can be experimentally determined with high accuracy. Further, it will be discussed how numerical electrothermal simulations can be carried out efficiently, allowing the accurate assessment of self-heating within a few minutes. The presented approach has been successfully verified experimentally for device temperatures exceeding 500 ◦C up to the onset of thermal runaway.
Large power semiconductors are complex structures, their metallization usually containing many thousands of contacts or vias. Because of this, detailed FEM simulations of the whole device are nowadays not possible because of excessive simulation time.
This paper introduces a simulation approach which allows quick identification of critical regions with respect to lifetime by a simplified simulation. For this, the complex layers are replaced by a much simpler equivalent layer, allowing a simulation of the whole device even including its package. In a second step, precise simulations taking all details of the structure into account are carried out, but only for the critical regions of interest. Thus, this approach gives detailed results where required with consideration of the whole structure including packaging. Further, the simulation time requirements are very moderate.
DMOS transistors in integrated smart power technologies are often subject to cyclic power dissipation with substantial selfheating. This leads to repetitive thermo mechanical stress, causing fatigue of the on-chip metallization and limiting the lifetime. Hence, most designs use large devices for lower peak temperatures and thus reduced stress to avoid premature failures.
However, significantly smaller DMOS transistors are acceptable if the system reverts to a safer operating condition with lower stress when a failure is expected to occur in the near future. Hence, suitable early-warning sensors are required. This paper proposes a floating metal meander embedded between DMOS source and drain to detect an impending metallization failure. Measurement results of several variants will be presented and discussed, investigating their suitability as early warning indicators.
DMOS transistors often suffer from substantial self-heating during high power dissipation, which can lead to thermal destruction if the device temperature reaches excessive values. A successfully demonstrated method to reduce the peak temperature is the redistribution of power dissipation density from the hotter to the cooler device areas by careful layout modification. However, this is very tedious and time-consuming if complex-shaped devices as often found in industrial applications are considered.
This paper presents an approach for fully automatic layout optimization which requires only a few hours processing time. The approach is applied to complex shaped test structures which are investigated by measurements and electro-thermal simulations. Results show a significantly lower peak temperature and an energy capability gain of 84 %, offering potential for a 18 % size reduction of active area.
This paper presents a measurement setup and an assembly technique suitable for characterization of power semiconductor devices under very high temperature conditions exceeding 500°C. An important application of this is the experimental investigation of wide bandgap semiconductors. Measurement results are shown for a 1200V SiC MOSFET and a 650V depletion mode GaN HEMT.
A TLP system with a very low characteristic impedance of 1.5 Ω and a selectable pulse length from 0.5 to 6 μs is presented. It covers the entire operation region of many power semiconductors up to 700 V and 400 A. Ist applicability is demonstrated by determining the Output characteristics for two Cool MOS devices up to destruction.
The experimental characterization of the thermal impedance Zth of large power MOSFETs is commonly done by measuring the junction temperature Tj in the cooling phase after the device has been heated, preferably to a high junction temperature for increased accuracy. However, turning off a large heating current (as required by modern MOSFETs with low on-state resistances) takes some time because of parasitic inductances in the measurement system. Thus, most setups do not allow the characterization of the junction temperature in the time range below several tens of μs.
In this paper, an optimized measurement setup is presented which allows accurate Tj characterization already 3 μs after turn-off of heating. With this, it becomes possible to experimentally investigate the influence of thermal capacitances close to the active region of the device. Measurement results will be presented for advanced power MOSFETs with very large heating currents up to 220 A. Three bonding variants are investigated and the observed differences will be explained.
The loss contribution of a 2.3kW synchronous GaN-HEMT boost converter for an input voltage of 250V and an output voltage of 500V was analyzed. A simulation model which consists of two parts is introduced. First, a physics-based model is used to determine the switching losses. Then, a system simulation is applied to calculate the losses of the specific elements. This approach allows a fast and accurate system evaluation as required for further system optimization.
In this work, a hard- and a zero-voltage turn-on switching converter are compared. Measurements were performed to verify the simulation model, showing a good agreement. A peak efficiency of 99% was achieved for an output power of 1.4kW. Even with an output power above 400W, it was possible to obtain a system efficiency exceeding 98 %.
Influence of metallization layout on aging detector lifetime under cyclic thermo-mechanical stress
(2016)
The influence of the layout on early warning detectors in BCD technologies for metallization failure under cyclic thermo-mechanical stress was investigated. Different LDMOS transistors, with narrow or wide metal fingers and with or without embedded detectors, were used. The test structures were repeatedly stressed by pronounced self-heating until failure (a short circuit) was detected. The results show that the layout of the on-chip metallization has a large impact on the lifetime. A significant influence of the detectors on the lifetime was also observed, in our case causing a reduction of more than a factor of two, but only for the test structure with narrow metal fingers. The experimental results are explained by an efficient numerical thermo mechanical simulation approach, giving detailed insights into the strain distribution in the metal system. These results are important for aging detector design and, morever, for LDMOS on-chip metal layout in general.
This work investigates the electro-thermal behavior and failure mechanism of a 600V depletion-mode GaN HEMT by experimental analysis and numerical thermal simulations. For this device, the positive temperature coefficient of the draingate leakage current can lead to the formation of hot spots. This localized thermal runaway which ultimately results in a breakdown of the inherent drain-gate junction is found to be the dominant cause of failure.