Refine
Document Type
- Conference proceeding (41) (remove)
Is part of the Bibliography
- yes (41)
Institute
- Technik (41) (remove)
A millimeter-wave power amplifier concept in an advanced silicon germanium (SiGe) BiCMOS technology is presented. The goal of the concept is to investigate the impact of physical limitations of the used heterojunction bipolar transistors (HBT) on the performance of a 77 GHz power amplifier. High current behavior, collectorbase breakdown and transistor saturation can be forced with the presented design. The power amplifier is manufactured in an advanced SiGe BiCMOS technology at Infineon Technologies AG with a maximum transit frequency fT of around 250 GHz for npn HBT’s [1]. The simulation results of the power amplifier show a saturated output power of 16 dBm at a power added efficiency of 13%. The test chip is designed for a supply voltage of 3.3 V and requires a chip size of 1.448 x 0.930 mm².
Die Nachfrage nach kompakten Spannungsversorgungen ist in den letzten Jahren stark gestiegen. Vor allem im Bereich der mobilen Geräte wachsen die Anforderung an die Spannungsversorgung hinsichtlich Bauvolumen und Batterielaufzeit. Für die Vollintegration von DC-DC- Wandlern als „Power Supply on Chip“ ist der SC-Wandler (Switched-Capacitor-Wandler) besonders geeignet. Insbesondere für Low-Power-Anwendungen im Bereich 10 mW kann ein SC-Wandler sehr gut, ohne externe Bauelemente, integriert werden. Während es für niedrige Eingangsspannungen (bis zu 5 V) eine Vielzahl an Topologien und Konzepten gibt, wurden SC-Wandler für höhere Eingangsspannungen (> 8 V) bisher nur wenig untersucht. Dieser Beitrag untersucht die wichtigsten Grundlagen für SC-Wandler mit Schwerpunkt auf hoher und zugleich variabler Eingangsspannung im Bereich 5 - 20 V. Am Beispiel eines Multi-Ratio-Wandlers (Wandler mit mehreren Übersetzungsverhältnissen), dem rekursiven SC-Wandler (RSC- Wandler), werden die Anforderungen eines SC- Wandler für hohe Eingangsspannungen herausgearbeitet und diskutiert.
In dieser Arbeit wird eine optimierte Bandgap-Referenz zur Erzeugung einer temperaturstabilen Spannung und eines Referenzstroms vorgestellt. Für Low-Power-Anwendungen wurde die Bandgap-Referenz, basierend auf der Brokaw-Zelle, mit minimaler Stromaufnahme und optimierter Chipfläche durch Multi-Emitter-Layout der Bipolartransistoren implementiert. Zusätzliches Merkmal ist ein verbreiteter Versorgungsspannungsbereich von 2,5 bis 5,5 V. Simulationen zeigen, dass eine stabile Ausgangsspannung von 1,218 V und ein Referenzstrom von 1,997 μA realisiert wird. Im Temperaturbereich -40 °C … 50 °C sowie dem gesamten Bereich der Versorgungsspannung beträgt die Genauigkeit der Referenzspannung ± 0,04 % mit einer Gesamtstromaufnahme zwischen 3,5 und 10 μA. Es wird eine Temperaturdrift von 2,18 ppm/K erreicht. Durch das elektronische Trimmen von Widerständen wird der Offset der Ausgangsspannung, bedingt durch Herstellungstoleranzen, auf ±3,5 mV justiert. Die Referenz wird in einer 0,18 μm BiCMOS-Technologie implementiert.
Durch schnell schaltende Leistungsendstufen werden durch kapazitive Umladeströme Störungen ins Substrat und in empfindliche Schaltungselemente eingekoppelt, die dort zur Störung der Funktion führen können. In dieser Arbeit werden Substratstrukturen zur gezielten Ableitung dieser Störungen vorgestellt und ihre Wirksamkeit mit Hilfe von Device Simulation evaluiert. Ohne Ableitstrukturen kann eine Potentialanhebung des Substrats bis zu 20 V entstehen. Die Untersuchungen belegen, dass die Potentialanhebung durch p-Typ Guard-Ringe um 75 %, durch leitende Trenches um 88 % sowie durch Rückseitenmetallisierung um nahezu 100 % reduziert werden kann.
Bootstrap circuits are mainly used for supplying a gate driver circuit to provide the gate overdrive voltage for a high-side NMOS transistor. The required charge has to be provided by a bootstrap capacitor which is often too large for integration if an acceptable voltage dip at the capacitor has to be guaranteed. Three options of an area efficient bootstrap circuit for a high side driver with an output stage of two NMOS transistors are proposed. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and connected when the gate driver turns on. A high voltage swing at the second capacitor leads to a high charge allocation. Both bootstrap capacitors require up to 70% less area compared to a conventional bootstrap circuit. This enables compact power management systems with fewer discrete components and smaller die size. A calculation guideline for optimum bootstrap capacitor sizing is given. The circuit was manufactured in a 180nm high-voltage BiCMOS technology as part of a high-voltage gate driver. Measurements confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit including two stacked 75.8pF and 18.9pF capacitors results in a voltage dip lower than 1V. This matches well with the theory of the calculation guideline.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
In recent years, significant progress has been made on switched-capacitor DC-DC converters as they enable fully integrated on-chip power management. New converter topologies overcame the fixed input-to-output voltage limitation and achieved high efficiency at high power densities. SC converters are attractive to not only mobile handheld devices with small input and output voltages, but also for power conversion in IoE, industrial and automotive applications, etc. Such applications need to be capable of handling widely varying input voltages of more than 10V, which requires a large amount of conversion ratios. The goal is to achieve a fine granularity with the least number of flying capacitors. In [1] an SC converter was introduced that achieves these goals at low input voltage VIN ≤ 2.5V. [2] shows good efficiency up to VIN = 8V while its conversion ratio is restricted to ≤1/2 with a limited, non-equidistant number of conversion steps. A particular challenge arises with increasing input voltage as several loss mechanisms like parasitic bottom-plate losses and gate-charge losses of high-voltage transistors become of significant influence. High input voltages require supporting circuits like level shifters, auxiliary supply rails etc., which allocate additional area and add losses [2-5]. The combination of both increasing voltage and conversion ratios (VCR) lowers the efficiency and the achievable output power of SC converters. [3] and [5] use external capacitors to enable higher output power, especially for higher VIN. However, this is contradictory to the goal of a fully integrated power supply.