Refine
Document Type
Language
- English (14) (remove)
Is part of the Bibliography
- yes (14)
Institute
- Technik (14)
Publisher
- IEEE (12)
- Copernicus GmbH (1)
An integrated synchronous buck converter with a high resolution dead time control for input voltages up to 48V and 10MHz switching frequency is presented. The benefit of an enhanced dead time control at light loads to enable zero voltage switching at both the high-side and low-side switch at low output load is studied. This way, compact multi-MHz DCDC converters can be implemented at high efficiency over a wide load current range. The concept also eliminates body diode forward conduction losses and minimizes reverse recovery losses. A dead time resolution of 125 ps is realized by an 8-bit differential delay chain. A further efficiency enhancement by soft switching at the high-side switch at light load is achieved with a voltage boost of the switching node by dead time control in forced continuous conduction mode. The monolithic converter is implemented in an 180nm high-voltage BiCMOS technology. At V IN = 48V, V OUT = 5V, 50mA load, 10MHz switching frequency and 500 nH output inductance, the efficiency is measured to be increased by 14.4% compared to a conventional predictive dead time control. A peak efficiency of 80.9% is achieved at 12V input.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
A generic, knowledge-based method for automatic topology selection of analog circuits in a predefined analog reuse library is presented in this paper on the OTA (Operational Transconductance Amplifier) example. Analog circuits of a given circuit class are classified in a topology tree, where each node represents a specific topology. Child nodes evolve from their parent nodes by an enhancement of the parent node’s topological structure. Topology selection is performed by a depth first-search in the topology tree starting at the root node, thus checking topologies of increasing complexity. The decisions at each node are based on solving equations or – if this is not possible – on simulations. The search ends at the first (and thus the simplest) topology which can meet the specification after an adequate circuit sizing. The advantages of the generic, tree based topology selection method presented in this paper are shown in comparison to a pool selection method and to heuristic approaches. The selection is based on an accomplished chip investigation.
We present a new methodology for automatic selection and sizing of analog circuits demonstrated on the OTA circuit class. The methodology consists of two steps: a generic topology selection method supported by a “part-sizing” process and subsequent final sizing. The circuit topologies provided by a reuse library are classified in a topology tree. The appropriate topology is selected by traversing the topology tree starting at the root node. The decision at each node is gained from the result of the part-sizing, which is in fact a node-specific set of simulations. The final sizing is a simulation-based optimization. We significantly reduce the overall simulation effort compared to a classical simulation-based optimization by combining the topology selection with the part-sizing process in the selection loop. The result is an interactive user friendly system, which eases the analog designer’s work significantly when compared to typical industrial practice in analog circuit design. The topology selection method and sizing process are implemented as a tool into a typical analog design environment. The design productivity improvement achievable by our method is shown by a comparison to other design automation approaches.
Size and cost of a boost converter can be minimized by reducing the voltage overshoot and fastening the transient response in case of load transient. The presented technique improves the transient response of a current mode controlled boost converter, which usually suffers from bandwidth limitation because of its right-half-plane zero (RHPZ). The proposed technique comprises a load current estimation which works as part of a digital controller without any additional measurements. Based on the latest load estimation the controller parameters are adapted, achieving small voltage overshoot and fast transient response. The presented technique was implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology, a Xilinx Spartan-6 field programmable gate array (FPGA), and a TI-ADS8422 analog to-digital-converter (ADC). Simulation and measurements of a 4V-to-6.3V, 500mA boost converter show an improvement of 50% in voltage overshoot and response time to load transient.
Boost converters suffer from a bandwidth limitation caused by the right-half plane zero (RHPZ), which occurs in the control-to-output transfer function. In contrast, there are many applications that require superior dynamic behavior. Further, size and cost of boost converter systems can be minimized by reduced voltage deviations and fast transient responses in case of large signal load transients. The key idea of the proposed ΔV/Δt-intervention control concept is to adapt the controller output to its new steady state value immediately after a load transient by prediction from known parameters. The concept is implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology and a Xilinx Spartan-6 field programmable gate array (FPGA). In a boost converter with 3.5V input voltage, 6.3V output voltage, 1.2A load, and 500 kHz switching frequency, the output voltage deviations are 2.8x smaller, scaling down the output capacitor value by the same factor. The recovery times are 2.4x shorter in case of large signal load transients with the proposed concept. The control is widely applicable, as it supports constant switching frequencies and allows for duty cycle and inductor current limitations. It also shows various advantages compared to conventional control and to selected adaptive control concepts.
This paper presents a digitally controlled boost converter IC for high output voltage and fast transient applications. Thus, it is well applicable in automotive and industrial environments. The 3V-to-6V input voltage, 6.3V output voltage, 1A boost converter IC is fabricated in a 180nm BCD technology. Digital control enables cost savings, advanced control concepts, and it is less parameter sensitive compared to common analog control. A 90 ns latency, 6-bit delay line ADC operates with a window concept, meeting high resolution requirements, e.g. in car battery applications. An output voltage live tracking is included for extending the ADC conversion window. A charge pump DAC provides high resolution, monotonicity, and short 128 ns conversion time. Further, a standard digital PI controller is enhanced by a simple but effective ΔV/Δt-intervention control. It results in 2.8x reduced output voltage deviations in case of load steps, scaling down the output capacitor value by the same factor.
Switched-mode power supplies (SMPS) convert an input DC-voltage into a higher or lower output voltage. In automotive, analog control is mostly used in order to keep the required output voltages constant and resistant to disturbances. The design of robust analog control for SMPS faces parameter variations of integrated and external passive components. Using digital control, parameter variations can be eliminated and the required area for the integrated circuit can be reduced at the same time.
Digital control design bears challenges like the prevention of limit cycle oscillations and controller wind-up. This paper reviews how to prevent these effects. Digital control loops introduce new sources for dead times in the control loop, for example the latency of the analog-to-digitalconverter (ADC). Dead times have negative influence on the stability of the control loop, because they lead to phase delays. Consequently, low latency is one of the key requirements for analog-to-digital converters in digitally controlled SMPS.
Exploiting the example of a 500 kHz-buck converter with a crossover frequency of 70 kHz, this paper shows that the 5 μs-latency of a 16-analog-to-digital-converter leads to a reduction in phase margin of 126°. The latency is less critical for boost converters because of their inherent lower crossover frequencies.
Finally, the paper shows a comparison between analog and digital control of SMPS with regard to chip area and test costs.
A highly integrated synchronous buck converter with a predictive dead time control for input voltages >18 V with 10 MHz switching frequency is presented. A high resolution dead time of ˜125 ps allows to reduce dead time dependent losses without requiring body diode conduction to evaluate the dead time. High resolution is achieved by frequency compensated sampling of the switching node and by an 8 bit differential delay chain. Dead time parameters are derived in a comprehensive study of dead time depended losses. This way, the efficiency of fast switching DC-DC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching. High-speed circuit blocks for fast switching operation are presented including level shifter, gate driver, PWM generator. The converter has been implemented in a 180 nm high-voltage BiCMOS technology.