Life Sciences
Refine
Document Type
- Journal article (286)
- Book chapter (26)
- Conference proceeding (11)
- Doctoral Thesis (7)
- Book (6)
- Patent / Standard / Guidelines (4)
- Working Paper (2)
- Review (1)
Is part of the Bibliography
- yes (343)
Institute
- Life Sciences (343)
- ESB Business School (1)
- Texoversum (1)
Publisher
- Elsevier (66)
- MDPI (49)
- Wiley (41)
- Springer (34)
- De Gruyter (26)
- American Chemical Society (22)
- Royal Society of Chemistry (9)
- IOP Publishing (8)
- Macmillan Publishers Limited (5)
- Frontiers Media (4)
Determination of the gel point of formaldehyde-based wood adhesives by using a multiwave technique
(2023)
Determining the instant of gelation of formaldehyde-based wood adhesives as an assessment parameter for their curing rate is important for optimizing the curing behavior. Due to the stoichiometrically imbalanced networks of formaldehyde-based adhesives, the crossover point of storage G′ and loss modulus G″ cannot unconditionally be assumed as the gel point in oscillatory time sweeps as the material response is frequency-dependent. This study aims to determine the gel point of selected adhesives by the isothermal multiwave oscillatory shear test. A thorough comparison between the gel and the crossover point of G′ and G″ is performed. Rheokinetic analysis showed no significant difference between the activation energies calculated at the gel point determined by a multiwave test and the crossover point obtained by the time sweep test. Hence, for resins with similar curing reactions, a reliable determination of gel point by applying a multiwave test is needed for a comparison of their reactivity.
Sol-gel-controlled size and morphology of mesoporous silica microspheres using hard templates
(2023)
Mesoporous silica microspheres (MPSMs) represent a promising material as a stationary phase for HPLC separations. The use of hard templates provides a preparation strategy for producing such monodisperse silica microspheres. Here, 15 MPSMs were systematically synthesized by varying the sol–gel reaction parameters of water-to-precursor ratio and ammonia concentration in the presence of a porous p(GMA-co-EDMA) polymeric hard template. Changing the sol–gel process factors resulted in a wide range of MPSMs with varying particle sizes from smaller than one to several micrometers. The application of response surface methodology allowed to derive quantitative predictive models based on the process factor effects on particle size, pore size, pore volume, and specific surface area of the MPSMs. A narrow size distribution of the silica particles was maintained over the entire experimental space. Two larger-scale batches of MPSMs were prepared, and the particles were functionalized with trimethoxy(octadecyl) silane for the application as stationary phase in reversed-phases liquid chromatography. The separation of proteins and amino acids was successfully accomplished, and the effect of the pore properties of the silica particles on separation was demonstrated.
Mesoporous silica microspheres (MPSMs) find broad application as separation materials in high liquid chromatography (HPLC). A promising preparation strategy uses p(GMA-co-EDMA) as hard templates to control the pore properties and a narrow size distribution of the MPMs. Here six hard templates were prepared which differ in their porosity and surface functionalization. This was achieved by altering the ratio of GMA to EDMA and by adjusting the proportion of monomer and porogen in the polymerization process. The various amounts of GMA incorporated into the polymer network of P1-6 lead to different numbers of tetraethylene pentamine in the p(GMA-co-EDMA) template. This was established by a partial least squares regression (PLS-R) model, based on FTIR spectra of the templates. Deposition of silica nanoparticles (SNP) into the template under Stoeber conditions and subsequent removal of the polymer by calcination result in MPSM1-6. The size of the SNPs and their incorporation depends on the pore parameters of the template and degree of TEPA functionalization. Moreover, the incorporated SNPs construct the silica network and control the pore parameters of the MPSMs. Functionalization of the MPSMs with trimethoxy (octadecyl) silane allows their use as a stationary phase for the separation of biomolecules. The pore characteristics and the functionalization of the template determine the pore structure of the silica particles and, consequently, their separation properties.
High-performance liquid chromatography is one of the most important analytical tools for the identification and separation of substances. The efficiency of this method is largely determined by the stationary phase of the columns. Although monodisperse mesoporous silica microspheres (MPSM) represent a commonly used material as stationary phase their tailored preparation remains challenging. Here we report on the synthesis of four MPSMs via the hard template method. Silica nanoparticles (SNPs) which form the silica network of the final MPSMs were generated in situ from tetraethyl orthosilicate (TEOS) in the presence of (3-aminopropyl) triethoxysilane (APTES) functionalized p(GMA-co-EDMA) as hard template. Methanol, ethanol, 2-propanol, and 1-butanol were applied as solvents to control the size of the SNPs in the hybrid beads (HB). After calcination, MPSMs with different sizes, morphology and pore properties were obtained and characterized by scanning electron microscopy, nitrogen adsorption and desorption measurements, thermogravimetric analysis, solid state NMR and DRIFT IR spectroscopy. Interestingly, the 29Si NMR spectra of the HBs show T and Q group species which suggests that there is no covalent linkage between the SNPs and the template. The MPSMs were functionalized with trimethoxy (octadecyl) silane and used as stationary phases in reversed-phase chromatography to separate a mixture of eleven different amino acids. The separation characteristics of the MPSMs strongly depend on their morphology and pore properties which are controlled by the solvent during the preparation of the MPSMs. Overall, the separation behavior of the best phases is comparable with those of commercially available columns. The phases even achieve faster separation of the amino acids without loss of quality.
This study introduces a straightforward approach to construct three-dimensional (3D) surface-enhanced Raman spectroscopy (SERS) substrates using chemically modified silica particles as microcarriers and by attaching metal nanoparticles (NPs) onto their surfaces. Tollens’ reagent and sputtering techniques are utilized to prepare the SERS substrates from mercapto-functionalized silica particles. Treatment with Tollens’ reagent generates a variety of silver NPs, ranging from approximately 10 to 400 nm, while sputtering with gold (Au) yields uniformly distributed NPs with an island-like morphology. Both substrates display wide plasmon resonances in the scattering spectra, making them effective for SERS in the visible spectral range, with enhancement factors (ratio of the analyte’s intensity at the hotspot compared to that on the substrate in the absence of metal nanoparticles) of up to 25. These 3D substrates have a significant advantage over traditional SERS substrates because their active surface area is not limited to a 2D surface but offers a much greater active surface due to the 3D arrangement of the NPs. This feature may enable achieving much higher SERS intensity from within streaming liquids or inside cells/tissues.
Ecuador, traditionally an agricultural based economy, has a great potential for valorizing their industrial residues. This study, presents a techno-economic analysis for applying a novel biomass oxidation method to produce formic and acetic acids from coffee husk residues in Machala, Ecuador. The analysis determined that the time of return of investment was lower than 5 years, making this project economically feasible, when producing approx. 1000 tons of formic acid per year, which is enough for supplying the Ecuadorian market. This production, would reduce imports costs and develop the chemical industry in the country.
Cotton contamination by honeydew is considered one of the significant problems for quality in textiles as it causes stickiness during manufacturing. Therefore, millions of dollars in losses are attributed to honeydew contamination each year. This work presents the use of UV hyperspectral imaging (225–300 nm) to characterize honeydew contamination on raw cotton samples. As reference samples, cotton samples were soaked in solutions containing sugar and proteins at different concentrations to mimic honeydew. Multivariate techniques such as a principal component analysis (PCA) and partial least squares regression (PLS-R) were used to predict and classify the amount of honeydew at each pixel of a hyperspectral image of raw cotton samples. The results show that the PCA model was able to differentiate cotton samples based on their sugar concentrations. The first two principal components (PCs) explain nearly 91.0% of the total variance. A PLS-R model was built, showing a performance with a coefficient of determination for the validation (R2cv) = 0.91 and root mean square error of cross-validation (RMSECV) = 0.036 g. This PLS-R model was able to predict the honeydew content in grams on raw cotton samples for each pixel. In conclusion, UV hyperspectral imaging, in combination with multivariate data analysis, shows high potential for quality control in textiles.
We study three-color Förster resonance energy transfer (triple FRET) between three spectrally distinct fluorescent dyes, a donor and two acceptors, which are embedded in a single polystyrene nanosphere. The presence of triple FRET energy transfer is confirmed by selective acceptor photobleaching. We show that the fluorescence lifetimes of the three dyes are selectively controlled using the Purcell effect by modulating the radiative rates and relative fluorescence intensities when the nanospheres are embedded in an optical Fabry–Pérot microcavity. The strongest fluorescence intensity enhancement for the second acceptor can be observed as a signature of the FRET process by tuning the microcavity mode to suppress the intermediate dye emission and transfer more energy from donor to the second acceptor. Additionally, we show that the triple FRET process can be modeled by coupled rate equations, which allow to estimate the energy transfer rates between donor and acceptors. This fundamental study has the potential to extend the classical FRET approach for investigating complex systems, e.g., optical energy switching, photovoltaic devices, light-harvesting systems, or in general interactions between more than two constituents.
UV hyperspectral imaging (225 nm–410 nm) was used to identify and quantify the honey- dew content of real cotton samples. Honeydew contamination causes losses of millions of dollars annually. This study presents the implementation and application of UV hyperspectral imaging as a non-destructive, high-resolution, and fast imaging modality. For this novel approach, a reference sample set, which consists of sugar and protein solutions that were adapted to honeydew, was set-up. In total, 21 samples with different amounts of added sugars/proteins were measured to calculate multivariate models at each pixel of a hyperspectral image to predict and classify the amount of sugar and honeydew. The principal component analysis models (PCA) enabled a general differentiation between different concentrations of sugar and honeydew. A partial least squares regression (PLS-R) model was built based on the cotton samples soaked in different sugar and protein concentrations. The result showed a reliable performance with R2cv = 0.80 and low RMSECV = 0.01 g for the valida- tion. The PLS-R reference model was able to predict the honeydew content laterally resolved in grams on real cotton samples for each pixel with light, strong, and very strong honeydew contaminations. Therefore, inline UV hyperspectral imaging combined with chemometric models can be an effective tool in the future for the quality control of industrial processing of cotton fibers.
Rapid and robust quality monitoring of the composition of meat pastes is of fundamental importance in processing meat and sausage products. Here, an in-line near-infrared spectroscopy/micro-electro-mechanical-system-(MEMS)-based approach, combined with multivariate data analysis, was used for measuring the constituents fat, protein, water, and salt in meat pastes within a typical range of meat paste recipes. The meat pastes were spectroscopically characterized in-line with a novel process analyzer prototype. By integrating salt content in the calibration set, robust predictive PLSR models of high accuracy (R2 > 0.81) were obtained that take interfering matrix effects of the minor and NIR-inactive meat paste recipe component “salt” into account as well. The nonlinear blending behavior of salt concentration on the spectral features of meat pastes is discussed based on a designed mixture experiment with four systematically varied components.