Refine
Document Type
- Conference proceeding (120)
- Journal article (21)
Language
- English (141) (remove)
Has full text
- yes (141)
Is part of the Bibliography
- yes (141)
Institute
- Technik (141) (remove)
Publisher
- IEEE (141) (remove)
Boost converters suffer from a bandwidth limitation caused by the right-half plane zero (RHPZ), which occurs in the control-to-output transfer function. In contrast, there are many applications that require superior dynamic behavior. Further, size and cost of boost converter systems can be minimized by reduced voltage deviations and fast transient responses in case of large signal load transients. The key idea of the proposed ΔV/Δt-intervention control concept is to adapt the controller output to its new steady state value immediately after a load transient by prediction from known parameters. The concept is implemented in a digital control circuit, consisting of an ASIC in a 110 nm-technology and a Xilinx Spartan-6 field programmable gate array (FPGA). In a boost converter with 3.5V input voltage, 6.3V output voltage, 1.2A load, and 500 kHz switching frequency, the output voltage deviations are 2.8x smaller, scaling down the output capacitor value by the same factor. The recovery times are 2.4x shorter in case of large signal load transients with the proposed concept. The control is widely applicable, as it supports constant switching frequencies and allows for duty cycle and inductor current limitations. It also shows various advantages compared to conventional control and to selected adaptive control concepts.
This article proposes several modified quasi Z-source dc/dc boost converters. These can achieve soft-switching by using a clamp-switch network comprised of an active switch and a diode in parallel with a capacitor connected across one of the inductors of the Z-source network. In this way, ringing at the transistor switching node is mitigated, and the voltage at the turn-on of the transistor is reduced. Even a zero voltage switching (ZVS) of the main transistor is possible if the capacitor in the clamp-switch network is adequately chosen. The proposed circuit structure and operating mode are described and validated through simulations and measurements on a low-power prototype.
Verification of an active time constant tuning technique for continuous-time delta-sigma modulators
(2022)
In this work we present a technique to compensate the effects of R-C / g m -C time-constant (TC) errors due to process variation in continuous-time delta-sigma modulators. Local TC error compensation factors are shifted around in the modulator loop to positions where they can be implemented efficiently with finely tunable circuit structures, such as current-steering digital-to-analog converters (DAC). We apply our technique to a third-order, single-bit, low-pass continuous-time delta-sigma modulator in cascaded integrator feedback structure, implemented in a 0.35-μm CMOS process. A tuning scheme for the reference currents of the feedback DACs is derived as a function of the individual TC errors and verified by circuit simulations. We confirm the tuning technique experimentally on the fabricated circuit over a TC parameter variation range of ±20%. Stable modulator operation is achieved for all parameter sets. The measured performances satisfy the expectations from our theoretical calculations and circuit-level simulations.
The experimental characterization of the thermal impedance Zth of large power MOSFETs is commonly done by measuring the junction temperature Tj in the cooling phase after the device has been heated, preferably to a high junction temperature for increased accuracy. However, turning off a large heating current (as required by modern MOSFETs with low on-state resistances) takes some time because of parasitic inductances in the measurement system. Thus, most setups do not allow the characterization of the junction temperature in the time range below several tens of μs.
In this paper, an optimized measurement setup is presented which allows accurate Tj characterization already 3 μs after turn-off of heating. With this, it becomes possible to experimentally investigate the influence of thermal capacitances close to the active region of the device. Measurement results will be presented for advanced power MOSFETs with very large heating currents up to 220 A. Three bonding variants are investigated and the observed differences will be explained.
In this work, a comparison between different brushless harmonic-excited wound-rotor synchronous machines is performed. The general idea of all topologies is the elimination of the slip rings and auxiliary windings by using the already existing stator and rotor winding for field excitation. This is achieved by injecting a harmonic airgap field with the help of power electronics. This harmonic field does not interact with the fundamental field, it just transfers the excitation power across the airgap. Alternative methods with varying number of phases, different pole-pair combinations, and winding layouts are covered and compared with a detailed Finite-Element-parameterized model. Parasitic effects due to saturation and coupling between the harmonic and main windings are considered.
This paper investigates the electrothermal stability and the predominant defect mechanism of a Schottky gate AlGaN/GaN HEMT. Calibrated 3-D electrothermal simulations are performed using a simple semiempirical dc model, which is verified against high-temperature measurements up to 440°C. To determine the thermal limits of the safe operating area, measurements up to destruction are conducted at different operating points. The predominant failure mechanism is identified to be hot-spot formation and subsequent thermal runaway, induced by large drain–gate leakage currents that occur at high temperatures. The simulation results and the high temperature measurements confirm the observed failure patterns.
Most Question-answering (QA) systems rely on training data to reach their optimal performance. However, acquiring training data for supervised systems is both time-consuming and resource-intensive. To address this, in this paper, we propose TFCSG, an unsupervised similar question retrieval approach that leverages pre-trained language models and multi-task learning. Firstly, topic keywords in question sentences are extracted sequentially based on a latent topic-filtering algorithm to construct unsupervised training corpus data. Then, the multi-task learning method is used to build the question retrieval model. There are three tasks designed. The first is a short sentence contrastive learning task. The second is the question sentence and its corresponding topic sequence similarity judgment task. The third is using question sentences to generate their corresponding topic sequence task. The three tasks are used to train the language model in parallel. Finally, similar questions are obtained by calculating the cosine similarity between sentence vectors. The comparison experiment on public question datasets that TFCSG outperforms the comparative unsupervised baseline method. And there is no need for manual marking, which greatly saves human resources.
Virtual prototyping of integrated mixed-signal smart-sensor systems requires high-performance co-simulation of analog frontend circuitry with complex digital controller hardware and embedded real-time software. We use SystemC/TLM 2.0 in combination with a cycle-count accurate temporal decoupling approach to simulate digital components and firmware code execution at high speed while preserving clock cycle accuracy and, thus, real-time behavior at time quantum boundaries. Optimal time quanta ensuring real-time capability can be calculated and set automatically during simulation if the simulation engine has access to exact timing information about upcoming communication events. These methods fail in case of non-deterministic, asynchronous events resulting in a possibly invalid simulation result. In this paper, we propose an extension of this method to the case of asynchronous events generated by blackbox sources from which a-priori event timing information is not available, such as coupled analog simulators or hardware in the loop. Additional event processing latency and/or rollback effort caused by temporal decoupling is minimized by calculating optimal time quanta dynamically in a SystemC model using a linear prediction scheme. For an example smart-sensor system model, we show that quasi- periodic events that trigger activities in temporally decoupled processes are handled accurately after the predictor has settled.
When a bonding wire becomes too hot, it fuses and fails. The ohmic heat that is generated in the wire can be partially dissipated to a mold package. For this cooling effect the thermal contact between wire and package is an important parameter. Because this parameter can degrade over lifetime, the fusing of a bonding wire can also occur as a long-term effect. Another important factor is the thermal power generated in the vicinity of the bond pads. Nowadays, the reliability of bond wires relies on robust dimensioning based on estimations. Smaller package sizes increase the need for better predictive methods.
The Bond Calculator, a new thermo-electrical simulation tool, is able to predict the temperature profiles along bond wires of arbitrary dimensions in dependence on the applied arbitrary transient current profile, the mold surrounding the wire, and the thermal contact between wire and mold.
In this paper we closely investigated the spatial temperature profiles along different bond wires in air in order to make a first step towards the experimental verification of the simulation model. We are using infrared microscopy in order to measure the thermal radiation generated along the bond wire. This is easier to perform quantitatively in air than in the mold package, because of the non-negligible absorbance of the mold material in the infrared wavelength region.
This paper evaluates experimentally the susceptibility of IT-networks under influences and the threats of HPEM (High Power Electromagnetic) and IEMI (Intentional Electromagnetic Interferences). As HPEM source a PBG 5 (Pulse Burst Generator) adapted to a TEM (Transversal Electromagnetic) Horn type antenna and a 90 cm IRA (Impulse Radiating Antenna) type antenna is used. Different network cable types and categories with different lengths are used. The immunity of the IT network is examined and the breakdown failure rate of the system is defined for a PRF (Pulse Repetition Frequency) of 500 s-1 in duration of 10 seconds. Series of measurements were carried out and disturbances of keyboards, mouse, switches, distortions on monitors and failures of the IT network and, even crash of PCs were observed. It is shown amongst other that by increasing the pulse repetition rate or frequency, generic test IT-networks are more susceptible to interference. Obtained results provide another view of the susceptibility analysis of modern generic IT-networks against UWB-Threats.
Substrate coupling is a critical failure mechanism especially in fast-switching integrated power stages controlling high-side NMOS power FETs. The parasitic coupling across the substrate in integrated power stages at rise times of up to 500 ps and input voltages of up to 40V is investigated in this paper. The coupling has been studied for the power stage of an integrated buck converter. In particular, dedicated diverting and isolation structures against substrate coupling are analyzed by simulations and evaluated with measurements from test chips in 180nm high-voltage BiCMOS. The results are compared regarding effectiveness, area as well as implementation effort and cost. Back-side metalization shows superior characteristics with nearly 100% noise suppression. Readily available p-guard ring structures bring 75% disturbance reduction. The results are applicable to advanced and future power management solutions with fully integrated switched-mode power supplies at switching frequencies >10 MHz.
The deterioration of the shielding performance of electromagnetic interference finger stock gaskets in a corrosive environment is investigated. The visualization of the real contact area shows a drastic reduction of the engaged active contact region between fingers and their mating surfaces in presence of corrosives residues. In fact, additional openings occur besides the “Tlike” holes due to the porous nature of gaskets. This leads to a strong degradation of the shielding effectiveness. Modified Bethe’s theory is used to estimate the equivalent circuit parameters while the shielding effectiveness in terms of ratio between two transfer functions is obtained upon applying the filter theory. Quantitative measurements carried out for different gasket types show a good agreement with calculated results, demonstrating thus the validity of the approach.
Micro grids often consist of energy generators, storages and consumers with controllers which are not prepared for their integration into communication networks for energy systems. In this paper it will be presented, how standards from the field of energy automation can be applied in such controllers. The data for communication interfaces can be structured according to the IEC 61850- or the VHPREADY standard. It is investigated which requirements must be supported to implement such data models within the controllers. For the transmission of the data we propose the OPC UA protocol, which supports extensive security measures and which is today available for nearly all modern types of controllers and computers.
We present a compact battery charger topology for weight and cost sensitive applications with an average output current of 9A targeted for 36V batteries commonly found in electric bicycles. Instead of using a conventional boost converter with large DC-link capacitors, we accomplish PFC-functionality by shaping the charging current into a sin²-shape. In addition, a novel control scheme without input-current sensing is introduced. A-priori knowledge is used to implement a feed-forward control in combination with a closed-loop output current control to maintain the target current. The use of a full-bridge/half bridge LLC converter enables operation in a wide input-voltage range.
A fully featured prototype has been built with a peak output power of 1050W. An average output power of 400W was measured, resulting in a power density of 1.8 kW/dm³. At 9A charging current, a power factor of 0.96 was measured and the efficiency exceeds 93% on average with passive rectification.
The impact of pulse charging has been evaluated on a 400Wh battery which was charged with the proposed converter as well as CC-CV-charging for reference. Both charging schemes show similar battery surface temperatures.
In this paper, it aims to model wind speed time series at multiple sites. The five-parameter Johnson distribution is deployed to relate the wind speed at each site to a Gaussian time series, and the resultant m-dimensional Gaussian stochastic vector process Z(t) is employed to model the temporal-spatial correlation of wind speeds at m different sites. In general, it is computationally tedious to obtain the autocorrelation functions (ACFs) and cross-correlation functions (CCFs) of Z(t), which are different to those of wind speed times series. In order to circumvent this correlation distortion problem, the rank ACF and rank CCF are introduced to characterize the temporal-spatial correlation of wind speeds, whereby the ACFs and CCFs of Z(t) can be analytically obtained. Then, Fourier transformation is implemented to establish the cross-spectral density matrix of Z(t), and an analytical approach is proposed to generate samples of wind speeds at m different sites. Finally, simulation experiments are performed to check the proposed methods, and the results verify that the five-parameter Johnson distribution can accurately match distribution functions of wind speeds, and the spectral representation method can well reproduce the temporal-spatial correlation of wind speeds.
This article illustrates a method for sensorless control of a switched reluctance motor. The detection of the time instants for switching between the working phases is determined based on the evaluation of the switching frequency of the hysteresis current controllers for appropriately selected sensing phases. This enables a simple and cost efficient implementation. The method is compared with a pulse injection method in terms of efficiency and resolution.
Energy efficient electric control of drives is more and more important for electric mobility and manufacturing industries. Online dynamic optimization of induction machines is challenging due to the computational complexity involved and the variable power losses during dynamic operation of induction machines. This paper proposes a simple technique for sub-optimal online loss optimization using rotor flux linkage templates for energy efficient dynamic operation of induction machines. Such a rotor flux linkage template is given by a rotor flux linkage trajectory which is optimal for a specific scenario. This template is calculated in an offline optimization process. For a specific scenario during real time operation the rotor flux linkage is calculated by appropriately scaling the given template.
We present a fully automatic approach to real-time 3D face reconstruction from monocular in-the-wild videos. With the use of a cascaded-regressor-based face tracking and a 3D morphable face model shape fitting, we obtain a semidense 3D face shape. We further use the texture information from multiple frames to build a holistic 3D face representation from the video footage. Our system is able to capture facial expressions and does not require any person specific training. We demonstrate the robustness of our approach on the challenging 300 Videos in the Wild (300- VW) dataset. Our real-time fitting framework is available as an open-source library at http://4dface.org.
In this work we investigate the behavior of MIS- and Schottky-gate AlGaN/GaN HEMTs under high-power pulsestress. A special setup capable of applying pulses of constant power is used to evaluate the electro-thermal response in different operating points. For both types of devices, the time to failure was found to decrease with increasing drain-source voltage. Overall, the Schottky-gate device displays a higher pulse robustness. The pulse withstand time of the MIS-gate device is limited by the occurrence of a thermal instability at approximately 240°C while the Schottky-gate device displays a rapid increase of the gate leakage current prior to failure. The mechanism responsible for this gate current is further investigated by static and transient temperature measurements and yielded activation energies of 0.6 eV and 0.84 eV.
The loss contribution of a 2.3kW synchronous GaN-HEMT boost converter for an input voltage of 250V and an output voltage of 500V was analyzed. A simulation model which consists of two parts is introduced. First, a physics-based model is used to determine the switching losses. Then, a system simulation is applied to calculate the losses of the specific elements. This approach allows a fast and accurate system evaluation as required for further system optimization.
In this work, a hard- and a zero-voltage turn-on switching converter are compared. Measurements were performed to verify the simulation model, showing a good agreement. A peak efficiency of 99% was achieved for an output power of 1.4kW. Even with an output power above 400W, it was possible to obtain a system efficiency exceeding 98 %.
We present the results of an extensive characterization of the performance and stability of a third-order continuous-time delta-sigma modulator with active coefficient error compensation. Using our previously published coefficient tuning technique, process variation induced R-C time-constant (TC) errors in the forward signal path can be compensated indirectly using continuously tunable DACs in the feedback path. To validate our technique experimentally with a range of real TC variations, we designed a modulator with discretely configurable integration capacitor arrays in a 0.35-μm CMOS process. We configured the capacitors of the fabricated device for a range of total TC variations from -28.4 % to +19.3 % and measured the signal-to-noise ratio (SNR) as a function of the input amplitude before and after compensating the variations electrically using the feedback DACs. The results show that our tuning technique is capable of restoring the desired nominal modulator performance over the entire parameter variation range, including the system’s nominal maximum stable amplitude (MSA).
While digital IC design is highly automated, analog circuits are still handcrafted in a time-consuming, manual fashion today. This paper introduces a novel Parameterized Circuit Description Scheme (PCDS) for the development of procedural analog schematic generators as parameterized circuits. Circuit designers themselves can use PCDS to create circuit automatisms which capture valuable expert knowledge, offer full topological flexibility, and enhance the re-use of well-established topologies. The generic PCDS concept has been successfully implemented and employed to create parameterized circuits for a broad range of use cases. The achieved results demonstrate the efficiency of our PCDS approach and the potential of parameterized circuits to increase automation in circuit design, also to benefit physical design by promoting the common schematic-driven-layout flow, and to enhance the applicability of circuit synthesis approaches.
Nowadays, the demand for a MEMS development/design kit (MDK) is even more in focus than ever before. In order to achieve a high quality and cost effectiveness in the development process for automotive and consumer applications, an advanced design flow for the MEMS (micro electro mechanical systems) element is urgently required. In this paper, such a development methodology and flow for parasitic extraction of active semiconductor devices is presented. The methodology considers geometrical extraction and links the electrically active pn junctions to SPICE standard library models and subsequently extracts the netlist. An example for a typical pressure sensor is presented and discussed. Finally, the results of the parasitic extraction are compared with fabricated devices in terms of accuracy and capability.
In a digitally controlled slope shaping system, reliable detection of both voltage and current slope is required to enable a closed-loop control for various power switches independent of system parameters. In most state-of-the-art works, this is realized by monitoring the absolute voltage and current values. Better accuracy at lower DC power loss is achieved by sensing techniques for a reliable passive detection, which is achieved through avoiding DC paths from the high voltage network into the sensing network. Using a high-speed analog-to-digital converter, the whole waveform of the transient derivative can be stored digitally and prepared for a predictive cycle-by-cycle regulation, without requiring high-precision digital differentiation algorithms. To gain an accurate representation of the voltage and current derivative waveforms, system parasitics are investigated and classified in three sections: (1) component parasitics, which are identified by s-parameter measurements and extraction of equivalent circuit models, (2) PCB design issues related to the sensing circuit, and (3) interconnections between adjacent boards.
The contribution of this paper is an optimized sensing network on the basis of the experimental study supporting fast transition slopes up to 100 V/ns and 1 A/ns and beyond, making the sensing technique attractive for slope shaping of fast switching devices like modern generation IGBTs, CoolMOSTM and SiC mosfets. Measurements of the optimized dv/dt and di/dt setups are demonstrated for a hard switched IGBT power stage.
This paper presents a control strategy for optimal utilization of photovoltaic (PV) generated power in conjunction with an Energy Storage System (ESS). The ESS is specifically designed to be retrofitted into existing PV systems in an end-user application. It can be attached in parallel to the PV system and connects to existing DC/AC inverters. In particular, the study covers the impact such a modification has on the output power of existing PV panels. A distinct degradation of PV output power was found due to the different power characteristics of PV panel and ESS. To overcome such degradation a novel feedback system is proposed. The feedback system continuously modifies the power characteristic of the ESS to match the PV panel and thus achieves optimal power utilization. Impact on PV and power point tracking performance is analyzed. Simulation of the proposed system is performed in MATLAB/Simulink. The results are found to be satisfactory.
This paper discusses the optimal control problem for increasing the energy efficiency of induction machines in dynamic operation including field weakening regime. In an offline procedure optimal current and flux trajectories are determined such that the copper losses are minimized during transient operations. These trajectories are useful for a subsequent online implementation.
In many automotive applications, repetitive selfheating is the most critical operation condition for LDMOS transistors in smart power ICs. This is attributed to thermomechanical stress in the on-chip metallization, which results from the different thermal expansion coefficients of the metal and the intermetal dielectric. After many cycles, the accumulated strain in the metallization can lead to short circuits, thus limiting the lifetime. Increasing the LDMOS size can help to lower peak temperatures and therefore to reduce the stress. The downside of this is a higher cost. Hence, it has been suggested to use resilient systems that monitor the LDMOS metallization and lower the stress once a certain level of degradation is reached. Then, lifetime requirements can be fulfilled without oversizing LDMOS transistors, even though a certain performance loss has to be accepted. For such systems, suitable sensors for metal degradation are required. This work proposes a floating metal line embedded in the LDMOS metallization. The suitability of this approach has been investigated experimentally by test structures and shown to be a promising candidate. The obtained results will be explained by means of numerical thermo-mechanical simulations.
On the influence of ground and substrate on the radiation characteristics of planar spiral antennas
(2022)
The unidirectional radiation of spiral antennas mounted on a substrate requires the presence of a ground plane. In this work, we successively illustrate the impact of dielectric material and ground plane on the key metrics of a planar equiangular spiral antenna (PESA). For this purpose, a PESA mounted on several substrates with different dielectric properties and thicknesses is modeled and simulated. We introduce the tertiary current flowing on spiral arms when backed by a ground plane.
Novel design for a coreless printed circuit board transformer realizing high bandwidth and coupling
(2019)
Rogowski coils offer galvanic isolation and can measure alternating currents with a high bandwidth. Coreless printed circuit board (PCB) transformers have been used as an alternative to limit the additional stray inductance if a Rogowski coil can not be attached to the circuit. A new PCB transformer layout is proposed to reduce cost, decrease additional stray inductance, increase the bandwidth of current measurements and simplify the integration into existing designs.
SLAM systems are mainly applied for robot navigation while research on feasibility for motion planning with SLAM for tasks like bin-picking, is scarce. Accurate 3D reconstruction of objects and environments is important for planning motion and computing optimal gripper pose to grasp objects. In this work, we propose the methods to analyze the accuracy of a 3D environment reconstructed using a LSD-SLAM system with a monocular camera mounted onto the gripper of a collaborative robot. We discuss and propose a solution to the pose space conversion problem. Finally, we present several criteria to analyze the 3D reconstruction accuracy. These could be used as guidelines to improve the accuracy of 3D reconstructions with monocular LSD-SLAM and other SLAM based solutions.
The hotspot detection has received much attention in the recent years due to a substantial mismatch between lithography wavelength and semiconductor technology feature size. This mismatch causes diffraction when transferring the layout from design onto a silicon wafer. As a result, open or short circuits (i.e. lithography hotspots) are more likely to be produced. Additionally, increasing numbers of semiconductors devices on a wafer required more time for the lithography hotspot detection analysis. In this work, we propose a fast and accurate solution based on novel artificial neural network (ANN) architecture for precise lithography hotspot detection using a convolution neural network (CNN) adopting a state of-the-art technique. The experimental results showed that the proposed model gained accuracy improvement over current state-of-theart approaches. The final code has been made publicly available.
Galvanic isolated gate drivers require a control signal as well as energy transmission from the control side (lowside) to the driver side (high-side). An additional backward signal transmission is preferred for error signals, status information, etc. This is often realized by means of several transformers or opto-couplers. Decreasing the number of isolation elements results in lower cost and a higher degree of miniaturization. This work presents a gate driver with bidirectional signal transmission and energy transfer via one single transformer. The key concept proposed in this paper is to combine bootstrapping to deliver the main gate charge for the driven power switch with additional energy transfer via the signal transformer. This paper also presents a very efficient combination of energy transfer to two high-side supply rails with back channel amplitude modulation. This way an isolated gate driver can be implemented that allows 100% pulse-width modulation (PWM) duty cycle at low complexity and system cost. The proposed high-side driver IC with integrated power supply, modulation and demodulation circuits was manufactured in a 180nm high-voltage BiCMOS technology. Measurements confirm the concept of bidirectional signal transmission with a 1MBit/s amplitude modulation, 10/20MHz frequency modulation and a maximum power transmission of 14mW via the transformer.
This paper presents a fully integrated gate driver in a 180-nm bipolar CMOS DMOS (BCD) technology with 1.5-A max. gate current, suitable for normally OFF gallium nitride (GaN) power switches, including gate-injection transistors (GIT). Full-bridge driver architecture provides a bipolar and three-level gate drive voltage for a robust and efficient GaN switching. The concept of high voltage energy storing (HVES), which comprises an on-chip resonant LC tank, enables a very area-efficient buffer capacitor integration and superior gatedriving speed. It reduces the component count and the influence of parasitic gate-loop inductance. Theory and calculations confirm the benefits of HVES compared to other capacitor implementation methods. The proposed gate driver delivers a gate charge of up to 11.6 nC, sufficient to drive most types of currently available GaN power transistors. Consequently, HVES enables to utilize the fast switching capabilities of GaN for advanced and compact power electronics.
DMOS transistors in integrated power technologies are often subject to significant self-heating and thus high temperatures, which can lead to device failure and reduced lifetime. Hence, it must be ensured that the device temperature does not rise too much. For this, the influence of the on-chip metallization must be taken into account because of the good thermal conductivity and significant thermal capacitance of the metal layers on top of the active DMOS area. In this paper, test structures with different metal layers and vias configurations are presented that can be used to determine the influence of the onchip metallization on the temperature caused by self-heating. It will be shown how accurate results can be obtained to determine even the influence of small changes in the metallization. The measurement results are discussed and explained, showing how on-chip metallization helps to lower the device temperature. This is further supported by numerical simulations. The obtained insights are valuable for technology optimization, but are also useful for calibration of temperature simulators.
Influence of metallization layout on aging detector lifetime under cyclic thermo-mechanical stress
(2016)
The influence of the layout on early warning detectors in BCD technologies for metallization failure under cyclic thermo-mechanical stress was investigated. Different LDMOS transistors, with narrow or wide metal fingers and with or without embedded detectors, were used. The test structures were repeatedly stressed by pronounced self-heating until failure (a short circuit) was detected. The results show that the layout of the on-chip metallization has a large impact on the lifetime. A significant influence of the detectors on the lifetime was also observed, in our case causing a reduction of more than a factor of two, but only for the test structure with narrow metal fingers. The experimental results are explained by an efficient numerical thermo mechanical simulation approach, giving detailed insights into the strain distribution in the metal system. These results are important for aging detector design and, morever, for LDMOS on-chip metal layout in general.
In this paper a double hogger used in woodworking machines is considered. The machining tools are driven by induction machines operated by standard inverters. During production the load of these motors changes periodically between low load and high load at a given speed. This paper investigates the reduction of power losses in such an application using an appropriate energy efficient control strategy for the induction machines.
Improved inductive feed-forward for fast turn-on of power semiconductors during hard switching
(2019)
A transformer is used to increase the gate voltage during turn-on, thus reducing the necessary bias voltage of the gate driver. Counteracting the voltage dependency of the gate capacitance of high-voltage power devices, faster transitions are possible. The additional transformer only slighly increases the over-voltage during turn-off.
The Dual Active Bridge (DAB) is a very promising topology for future power converters. However, careless operation can lead to a DC component in the transformer current. The problem is further exacerbated when the phase shift changes during operation. This work presents a study of DC bias effects on the DAB with special regard to transient effects introduced by sudden shifts in the output load. We present a simple yet effective approach to avoid DC bias entirely.
Impact of a large distribution network on radiation characteristics of planar spiral antenna arrays
(2023)
Designing antenna arrays with a central feed point has gained ground in the antenna technique. This approach, which is usually applied because of manufacturing costs, is difficult to achieve and leads to a large feeding network. The impact of which is numerically investigated in the present work. Upon comparing three different antennas, it is shown that the enlargement of the feed strongly affects the antenna's overall dimensions and the antenna's radiation characteristics. The antenna with the plug-in solution is not only small in size but also performs better compared to antennas with a central feed point. Considering the high effort in designing the feed network with a central point and the influence of the resulting enlarged network on the dimensions and radiation characteristics of the antenna, the cost saving in production can be put into perspective.
Equations for fast and exact calculation of a simple model for heat transfer from a bond wire to a cylindrical finite mold package including nonideal heat transfer from wire to mold are presented. These allow for a characterization of an arbitrary mold/bond wire combination. The real mold geometry is approximated using the mold model cylinder radius and the thermal contact conductance of the mold/bond wire interface. For changes in bond and mold material, wire length, diameter, and current transient profiles, the resulting temperature transients can then be predicted. As the method is based on numerical integration of differential equations, arbitrary pulse shapes, which are industrially relevant, can be calculated. Very high thermal contact conductance values (above 40 000 W/m2K heat transfer) have been detected in real package/bond systems. The method was validated by successful comparison with finite element method simulations and alternative calculation methods and measurements.
The majority of people in sub-Saharan Africa (SSA) rely on so-called “paratransit” for their mobility needs. The term refers to a large informal transport sector that runs independent of government, of which 83% comprises minibus taxis (MBT). MBT technology is often old and contribute significantly to climate change with their high carbon dioxide (CO2) emissions. Issues related to sustainability and climate change are becoming more important world-wide and hardly any attention is given to MBTs. Converting the MBTs from internal combustion engines (ICEs) to electric motors could be a possible solution. The existing power grid in SSA is largely based on fossil power plants and is unstable. This can be seen by frequent local power blackouts. To avoid further strain on the existing power grid, it would therefore make sense to charge the electric minibus taxis (eMBTs) through a grid consisting of renewable energies. A mobility map is created via simulations with collected data points of the MBTs. By using this mobility map, the energy demand of the eMBTs is calculated. Furthermore, a region-specific photovoltaic (PV) and wind simulation can be realised based on existing weather data, and a tool to size the supply system to charge the eMBTs is developed after all data has been collected. With the help of this work, it can be determined to what extent renewable energies such as PV and wind power can be used to support the transition from ICEs to electric engines in the MBT sector.
In this work, a brushless, harmonic-excited wound-rotor synchronous machine is investigated which utilizes special stator and rotor windings. The windings magnetically decouple the fundamental torque-producing field from the harmonic field required for the inductive power transfer to the field coil. In contrast to conventional harmonic-excited synchronous machines, the whole winding is utilized for both torque production and harmonic excitation such that no additional copper for auxiliary windings is needed. Different rotor topologies using rotating power electronic components are investigated and their efficiencies have been compared based on Finite-Element calculation and circuit analysis.
Optimization-based design automation for analog ICs still remains behind the demands. A promising alternative is given by procedural approaches such as parameterized generators, also known as PCells. We are working on a complete analog design flow based on parameterized generators for entire circuits and corresponding layout modules. Because the conventional programming of such enhanced generators is far too complicated and costly, new methods are needed to ease their development. This paper presents gPCDS (graphical PCDS), a novel tool for a designer-oriented development of schematic module generators, integrated into a common schematic entry environment. The tool is based on PCDS (Parameterized Circuit Description Scheme), a meta-language for the creation of parametrized analog circuits. Schematic module generators are a very desirable complement to layout module generators in order to achieve a seamless schematic- driven layout design flow on module level. By facilitating a way of generator development that matches a design expert’s mentality, gPCDS contributes to close this gap in the analog design flow.
We propose a method for recognizing dynamic gestures using a 3D sensor. New aspects of the developed system include problem-adapted data conversion and compression as well as automatic detection of different variants of the same gesture via clustering with a suitable metric inspired by Jaccard metric. The combination of Hidden Markov Models and clustering leads to robust detection of different executions based on a small set of training data. We achieved an increase of 5% recognition rate compared to regular Hidden Markov Models. The system has been used for human-machine interaction and might serve as an assistive system in physiotherapy and neurological or orthopedic diagnosis.
The power supply is one of the major challenges for applications like internet of things IoTs and smart home. The maintenance issue of batteries and the limited power level of energy harvesting is addressed by the integrated micro power supply presented in this paper. Connected to the 120/230 Vrms mains, which is one of the most reliable energy sources and anywhere indoor available, it provides a 3.3V DC output voltage. The micro power supply consists of a fully integrated ACDC and DCDC converter with one external low voltage SMD buffer capacitor. The micro power supply is fabricated in a low cost 0.35 μm 700 V CMOS technology and covers a die size of 7.7 mm². The use of only one external low voltage SMD capacitor, results in an extremely compact form factor. The ACDC is a direct coupled, full wave rectifier with a subsequent bipolar shunt regulator, which provides an output voltage around 17 V. The DCDC stage is a fully integrated 4:1 SC DCDC converter with an input voltage as high as 17 V and a peak efficiency of 45 %. The power supply achieves an overall output power of 3 mW, resulting in a power density of 390 μW/mm². This exceeds prior art by a factor of 11.
Due to the lack of sophisticated component libraries for microelectromechanical systems (MEMS), highly optimized MEMS sensors are currently designed using a polygon driven design flow. The advantage of this design flow is its accurate mechanical simulation, but it lacks a method for an efficient and accurate electrostatic analysis of parasitic effects of MEMS. In order to close this gap in the polygon-driven design flow, we present a customized electrostatic analysis flow for such MEMS devices. Our flow features a 2.5D fabrication-process simulation, which simulates the three typical MEMS fabrication steps (namely deposition of materials including topography, deep reactive-ion etching, and the release etch by vapor-phase etching) very fast and on an acceptable abstraction level. Our new 2.5D fabrication-process simulation can be combined with commercial field-solvers such as they are commonly used in the design of integrated circuits. The new process simulation enables a faster but nevertheless satisfactory analysis of the electrostatic parasitic effects, and hence simplifies the electrical optimization of MEMS.
Reduction of power consumption of digital systems is a major concern especially in modern smart sensor systems. These systems are often only activated on request and their power consumption is therefore dominated by the idle-mode. Power reduction mechanisms such as clock or power gating reduce the activity or leakage in the purely digital circuits. We propose a novel adaptive clocking scheme that optimizes the energy demand using a fine-grained oscillator control on cycle-level. To evaluate our new approach, we analytically analyze the power consumption of the regarded system in comparison with available methods. The power of our new adaptive clocking is shown in an integrated smart sensor for capacitive measurements working in a passive wireless sensor node. Using our methods, we show that the energy demand of the example system is reduced even in the case of continuous measurements that demand for a high activity in the digital circuitry.
Layout generators, commonly denoted as PCells (parameterized cells), play an important role in the layout design of analog ICs (integrated circuits). PCells can automatically create parts of a layout, whose properties are controlled by the PCell parameters. Any layout, whether hand-crafted or automatically generated, has to be verified against design rules using a DRC (design rule check) in order to assure proper functionality and producibility. Due to the growing complexity of today’s PCells it would be beneficial if a PCell itself could be ensured to produce DRC clean layouts for any allowed parameter values, i.e. a formal verification of the PCell’s code rather than checking all possible instances of the PCell. In this paper we demonstrate the feasibility of such a formal PCell verification for a simple NMOS transistor PCell. The set from which the parameter values can be chosen was found during the verification process.
In this paper, we propose a novel fitting method that uses local image features to fit a 3D morphable face model to 2D images. To overcome the obstacle of optimising a cost function that contains a non-differentiable feature extraction operator, we use a learning-based cascaded regression method that learns the gradient direction from data. The method allows to simultaneously solve for shape and pose parameters. Our method is thoroughly evaluated on morphable model generated data and first results on real data are presented. Compared to traditional fitting methods, which use simple raw features like pixel colour or edge maps, local features have been shown to be much more robust against variations in imaging conditions. Our approach is unique in that we are the first to use local features to fit a 3D morphable model. Because of the speed of our method, it is applicable for realtime applications. Our cascaded regression framework is available as an open source library at github.com/patrikhuber/ superviseddescent.