660 Technische Chemie
Refine
Document Type
- Journal article (18) (remove)
Is part of the Bibliography
- yes (18)
Institute
- Life Sciences (18) (remove)
Publisher
- Wiley (7)
- Elsevier (6)
- De Gruyter (2)
- Hanser (1)
- IOP Publishing (1)
- MDPI (1)
Bioenergy production is a new and promising industry in Ecuador. However, a confusing variety of laws, which are spread among different regulating institutions, regulate the agricultural sector. Such dispersion makes it difficult for farmers and businesses to understand applicable rights, duties, regulations and agricultural policies. Moreover, this rather young industry lacks important experience. In the first section of this work, the existing Ecuadorian legislation on bioenergy is presented and analyzed. Then, a brief, thorough analysis and comparison are carried out for experiences not only in developed countries, but also with similar cultural frameworks and comparable climatic conditions. The results are summarized as specific recommendations that have been handed to the National Agricultural Chamber of Ecuador from academia for the proposal of a Unified Agricultural Code established in the Ecuadorian legal hierarchy as an Organic Law.
Fast pyrolysis as a valorization mechanism for banana rachis and low-density polyethylene waste
(2021)
Banana rachis and low-density polyethylene (LDPE) were selected as secondary feedstocks for the study of fast pyrolysis in a free-fall reactor. The experiments were performed at 600 °C for banana rachis and 450 °C for LDPE, based on literature and thermogravimetric analysis. The gaseous products of both feedstocks present similar composition in the C1-C2 compounds, while C3 compounds are only found in LDPE. The liquid products from banana and LDPE correspond to functional groups and shorter hydrocarbons, respectively. Scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) analyses of the char showed important morphological changes to spheres in LDPE and structural changes due to thermal decomposition in the biomass. The pyrolysis char has high potential as adsorbent, encapsulation, or catalyst.
Polycaprolactone (PCL) was electrospun with the addition of arginine (Arg), an α-amino acid that accelerates the haeling process. The efficient needleless electrospinning technique was used for the fabrication of the nanofibrous layers. The materials produced consisted mainly of fibers with diameters of between 200 and 400 nm. Moreover, both microfibers and beads were present within the layers. Higher bead sized were observed with the increased addition of arginine.
The self-healing effect of melamine-based surfaces, triggered by temperature, was investigated. The temperature triggered reversible healing chemistry, on which the self-healing effect is based, was the Diels-Alder (DA) reaction between furan and malemeide groups. Melamine-furan containing building blocks were connected by multi-functional maleimide crosslinker via a Diels-Alder (DA) reaction to giva a DA adduct. The DA adduct was then reacted with formaldehyde to form a network by conventional condensation reaction of melamine amino groups with formaldehyde. The obtained resin was characterised and used for the impregnation of paper. Impregnated papers and neat resin werde used to perform scratch-healing tests and mechanical analysis of the novel coating system.
Estimating molar solubility from the Hildebrand-Scott relation employing Hansen solubility parameters (HSP) is widely presumed a valid semi quantitative approach. To test this presumption and to determine quantitatively the inherent accuracy of such a solubility prognosis, l-ascorbic acid (LAA) was treated as an example of a commercially important solute. Analytical calculus and Monte Carlo (MC) simulation were performed for 20 common solvents with total HSP ranging from 14.5 to 33.0 (MPa)0.5 utilizing validated material data. It was found that, due to the uncertainty of the material data used in the calculations, the solubility prediction had a large scattering and, thus, a low precision.
We report an investigation into the distribution of copper oxidation states in oxide films formed on the surfaces of technical copper. The oxide films were grown by thermal annealing at ambient conditions and studied using Auger depth profiling and UV–Vis spectroscopy. Both Auger and UV–Vis data were evaluated applying multivariate curve resolution (MCR). Both experimental techniques revealed that the growth of Cu2O dominates the initial ca. 40 nm of oxide films grown at 175 °C, while further oxide growth is dominated by CuO formation. The largely coincident results from both experimental approaches demonstrates the huge benefit of the application of UV–Vis spectroscopy in combination with MCR analysis, which provides access to information on chemical state distributions without the need for destructive sample analysis. Both approaches are discussed in detail.
A new two-dimensional fluorescence sensor system was developed for in-line monitoring of mammalian cell cultures. Fluorescence spectroscopy allows for the detection and quantification of naturally occurring intra- and extracellular fluorophores in the cell broth. The fluorescence signals correlate the the cells' current redox state and other relevant process parameters. Cell culture pretests with twelve different excitation wavelengths showed that only three wavelengths account for a vast majority of spectral variation. Accordingly, the newly developed device utilizes three high-power LEDs as excitation sources in combination with a back-thinned CCD-spectrometer for fluorescence detection.
Die kontinuierliche Erfassung von Qualitätsparametern ist eine zunehmende Anforderung in der Polymerextrusion. Die optische Spektroskopie kann diese Anforderung erfüllen, da sie neben der Farbe weitere Parameter wie beispielsweise chemische Eigenschaften, Trübungsgrad oder Partikelgröße erfasst. Dabei werden für Inline-Messungen im Extruder optische Sonden eingesetzt. Im laufenden Betrieb bilden sich Ablagerungen auf den Sondenfenstern. Dieser Beitrag präsentiert ein neues Cleaning in Place Konzept, mit dessen Hilfe die Fenster auch während der Produktion ohne Unterbrechung gereinigt werden können. Auch die Kalibrierung der Messtechnik ist dabei möglich. Das verhindert Rüstzeiten und sichert eine kontinuierliche Inline-Messung.
In bioprinting approaches, the choice of bioink plays an important role since it must be processable with the selected printing method, but also cytocompatible and biofunctional. Therefore, a crosslinkable gelatin-based ink was modified with hydroxyapatite (HAp) particles, representing the composite buildup of natural bone. The inks’ viscosity was significantly increased by the addition of HAp, making the material processable with extrusion-based methods. The storage moduli of the formed hydrogels rose significantly, depicting improved mechanical properties. A cytocompatibility assay revealed suitable ranges for photoinitiator and HAp concentrations. As a proof of concept, the modified ink was printed together with cells, yielding stable three-dimensional constructs containing a homogeneously distributed mineralization and viable cells.
Adapting characteristics of biomaterials specifically for in vitro and in vivo applications is becoming increasingly important in order to control interactions between material and biological systems. These complex interactions are influenced by surface properties like chemical composition, charge, mechanical and topographic attributes. In many cases it is not useful or even not possible to alter the base material but changing surface, to improve biocompatibility or to make surfaces bioactive, may be achieved by thin coatings. An already established method is the coating with polyelectrolyte multilayers (PEM). To adjust adhesion, proliferation and improve vitality of certain cell types, we modified the roughness of PEM coatings. We included different types nanoparticles (NP’s) in different concentrations into PEM coatings for controlling surface roughness. Surface properties were characterized and the reaction of 3 different cell types on these coatings was tested.