Refine
Document Type
- Conference proceeding (222) (remove)
Language
- English (222) (remove)
Is part of the Bibliography
- yes (222)
Institute
- Technik (120)
- Informatik (83)
- ESB Business School (18)
- Texoversum (1)
Publisher
- IEEE (222) (remove)
This paper presents an integrated synchronous buck converter for input voltages >12V with 10MHz switching frequency. The converter comprises a predictive dead time control with frequency compensated sampling of the switching node which does not require body diode forward conduction. A high dead time resolution of 125 ps is achieved by a differential delay chain with 8-bit resolution. This way, the efficiency of fast switching DCDC converters can be optimized by eliminating the body diode forward conduction losses, minimizing reverse recovery losses and by achieving zero voltage switching at turn off. The converter was implemented in a 180nm high-voltage BiCMOS technology. The power losses were measured to be reduced by 30%by the proposed dead time control, which results in a 6% efficiency increase at VOUT = 5V and 0.2A load. The peak efficiency is 81 %.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum conversion ratio are limited by the duty cycle of a PWM signal. In DCDC converters, a sawtooth generator is the fundamental circuit block to generate the PWM signal. The presented PWM generator is based on two parallel, fully interleaved PWM generator stages, each containing an integrator based sawtooth generator and two 3-stage highspeed comparators. A digital multiplexing of the PWM signals of each stage eliminates the dependency of the minimum on-time on the large reset times of the sawtooth ramps. A separation of the references of the PWM comparators in both stage allows to configure the PWM generator for a DCDC converter operating in fixed frequency or in constant on-time mode, which requires an operation in a wide frequency range. The PWM generator was fabricated in an 180 nm HV BiCMOS technology, as part of a DCDC converter. Measurements confirm minimum possible ontime pulses as short as 2 ns and thus allows switching frequencies of DCDC converters of >50 MHz at small duty cycle of <10%. At moderate duty cycles switching frequencies up to 100 MHz are possible.
Substrate coupling is a critical failure mechanism especially in fast-switching integrated power stages controlling high-side NMOS power FETs. The parasitic coupling across the substrate in integrated power stages at rise times of up to 500 ps and input voltages of up to 40V is investigated in this paper. The coupling has been studied for the power stage of an integrated buck converter. In particular, dedicated diverting and isolation structures against substrate coupling are analyzed by simulations and evaluated with measurements from test chips in 180nm high-voltage BiCMOS. The results are compared regarding effectiveness, area as well as implementation effort and cost. Back-side metalization shows superior characteristics with nearly 100% noise suppression. Readily available p-guard ring structures bring 75% disturbance reduction. The results are applicable to advanced and future power management solutions with fully integrated switched-mode power supplies at switching frequencies >10 MHz.
When a bonding wire becomes too hot, it fuses and fails. The ohmic heat that is generated in the wire can be partially dissipated to a mold package. For this cooling effect the thermal contact between wire and package is an important parameter. Because this parameter can degrade over lifetime, the fusing of a bonding wire can also occur as a long-term effect. Another important factor is the thermal power generated in the vicinity of the bond pads. Nowadays, the reliability of bond wires relies on robust dimensioning based on estimations. Smaller package sizes increase the need for better predictive methods.
The Bond Calculator, a new thermo-electrical simulation tool, is able to predict the temperature profiles along bond wires of arbitrary dimensions in dependence on the applied arbitrary transient current profile, the mold surrounding the wire, and the thermal contact between wire and mold.
In this paper we closely investigated the spatial temperature profiles along different bond wires in air in order to make a first step towards the experimental verification of the simulation model. We are using infrared microscopy in order to measure the thermal radiation generated along the bond wire. This is easier to perform quantitatively in air than in the mold package, because of the non-negligible absorbance of the mold material in the infrared wavelength region.
A generic, knowledge-based method for automatic topology selection of analog circuits in a predefined analog reuse library is presented in this paper on the OTA (Operational Transconductance Amplifier) example. Analog circuits of a given circuit class are classified in a topology tree, where each node represents a specific topology. Child nodes evolve from their parent nodes by an enhancement of the parent node’s topological structure. Topology selection is performed by a depth first-search in the topology tree starting at the root node, thus checking topologies of increasing complexity. The decisions at each node are based on solving equations or – if this is not possible – on simulations. The search ends at the first (and thus the simplest) topology which can meet the specification after an adequate circuit sizing. The advantages of the generic, tree based topology selection method presented in this paper are shown in comparison to a pool selection method and to heuristic approaches. The selection is based on an accomplished chip investigation.
In this paper a double hogger used in woodworking machines is considered. The machining tools are driven by induction machines operated by standard inverters. During production the load of these motors changes periodically between low load and high load at a given speed. This paper investigates the reduction of power losses in such an application using an appropriate energy efficient control strategy for the induction machines.
A 20 V, 8 MHz resonant DCDC converter with predictive control for 1 ns resolution soft-switching
(2015)
Fast switching power supplies allow to reduce the size and cost of external passive components. However, the capacitive switching losses of the power stage will increase and become the dominant part of the total losses. Therefore, resonant topologies are the known key to reduce the losses of the power stage. A power switch with an additional resonant circuit can be turned on under soft-switching conditions, ideally with zero-voltage-switching (ZVS). As conventional resonant converts are only efficient for a constant load, this paper presents a predictive regulation loop to approach soft-switching conditions under varying load and component tolerances. A sample and hold based detection circuit is utilized to control the turn-on of the power switch by a digital regulation. The proposed design was fabricated in a 180 nm high-voltage BiCMOS technology. The efficiency of the converter was measured to be increased by up to 16 % vs. worst case timing and by 13 % compared to a conventional hard-switching buck converter at 20 V input voltage and at approximately 8 MHz switching frequency.
There is a growing need for motor drives with improved EMC in various automotive and industrial applications. An often referenced approach to reduce EME is to change the shape of the switching signal to reduce the EMI caused by the voltage and current transitions. This requires very precise gate control of the power MOSFET to achive better switching behaviour and lower EME without a major increase in switching losses. In order to find an optimal trade-off, this work utilizes a monolithic current mode gate driver with a variable output current that can be changed within 10ns. With this driver, measurements with different gate current profiles were taken. The di/dt transition was confirmed to be as important as the dv/dt transition in the power MOSFET. As a result of the improved switching behavior the emissions were reduced by up to 20dB between 7MHz and 60MHz with a switching loss that is 52% lower than with a constantly low gate current.
Galvanic isolated gate drivers require a control signal as well as energy transmission from the control side (lowside) to the driver side (high-side). An additional backward signal transmission is preferred for error signals, status information, etc. This is often realized by means of several transformers or opto-couplers. Decreasing the number of isolation elements results in lower cost and a higher degree of miniaturization. This work presents a gate driver with bidirectional signal transmission and energy transfer via one single transformer. The key concept proposed in this paper is to combine bootstrapping to deliver the main gate charge for the driven power switch with additional energy transfer via the signal transformer. This paper also presents a very efficient combination of energy transfer to two high-side supply rails with back channel amplitude modulation. This way an isolated gate driver can be implemented that allows 100% pulse-width modulation (PWM) duty cycle at low complexity and system cost. The proposed high-side driver IC with integrated power supply, modulation and demodulation circuits was manufactured in a 180nm high-voltage BiCMOS technology. Measurements confirm the concept of bidirectional signal transmission with a 1MBit/s amplitude modulation, 10/20MHz frequency modulation and a maximum power transmission of 14mW via the transformer.
While digital IC design is highly automated, analog circuits are still handcrafted in a time-consuming, manual fashion today. This paper introduces a novel Parameterized Circuit Description Scheme (PCDS) for the development of procedural analog schematic generators as parameterized circuits. Circuit designers themselves can use PCDS to create circuit automatisms which capture valuable expert knowledge, offer full topological flexibility, and enhance the re-use of well-established topologies. The generic PCDS concept has been successfully implemented and employed to create parameterized circuits for a broad range of use cases. The achieved results demonstrate the efficiency of our PCDS approach and the potential of parameterized circuits to increase automation in circuit design, also to benefit physical design by promoting the common schematic-driven-layout flow, and to enhance the applicability of circuit synthesis approaches.
Advanced power semiconductors such as DMOS transistors are key components of modern power electronic systems. Recent discrete and integrated DMOS technologies have very low area-specific on-state resistances so that devices with small sizes can be chosen. However, their power dissipation can sometimes be large, for example in fault conditions, causing the device temperature to rise significantly. This can lead to excessive temperatures, reduced lifetime, and possibly even thermal runaway and subsequent destruction. Therefore, it is required to ensure already in the design phase that the temperature always remains in an acceptable range. This paper will show how self-heating in DMOS transistors can be experimentally determined with high accuracy. Further, it will be discussed how numerical electrothermal simulations can be carried out efficiently, allowing the accurate assessment of self-heating within a few minutes. The presented approach has been successfully verified experimentally for device temperatures exceeding 500 ◦C up to the onset of thermal runaway.
This paper presents a new broadband antenna for satellite communications. It describes the procedure involved in the design of a microstrip antenna array and its multi-level passive feed network that together yield circular polarization and the necessary gain to be used in an earth-satellite link. The designed antenna is notable for its large bandwidth, circular polarization, high gain and small dimensions.
This paper presents the design and simulation processes of an Equiangular Spiral Antenna for the extremely high frequencies between 65 GHz and 170 GHz. A new approach for the analysis of the antenna’s electrical parameters is described. This approach is based on formalism proposed by Rumsey to determine the EM field produced by an equiangular spiral antenna. Analytical expressions of the electrical parameters such as the gain or the directivity are then calculated using well sustained mathematical approximations. The comparison of obtained results with those from numerical integration methods shows a good agreement.
Analysis and planning of Enterprise Architectures (EA) is a complex task for stakeholders. The change of one architecture element has impact on multiple other elements because of manifold relationships and interactions between them. The interactive cockpit approach presented in this paper supports stakeholders planning and analyzing EAs and to tackle the intrinsic complexity. This approach supplies a cockpit with multiple viewpoints to put relevant information side-by-side without losing the context combined with interaction functionality. In this paper, we develop such cockpit starting with relevant use cases, describing a potential design based on well-established foundations in EA modeling, and outline an exemplary usage scenario.
Model-guided Therapy and Surgical Workflow Systems are two interrelated research fields, which have been developed separately in the last years. To make full use of both technologies, it is necessary to integrate them and connect them to Hospital Information Systems. We propose a framework for integration of Model-guided Therapy in Hospital Information Systems based on the Electronic Medical Record, and a taskbased Workflow Management System, which is suitable for clinical end users. Two prototypes - one based on Business Process Modeling Language, one based on the serum-board - are presented. From the experience with these prototypes, we developed a novel personalized visualization system for Surgical Workflows and Model-guided Therapy. Key challenges for further development are automated situation detection and a common communication infrastructure.
Current approaches for enterprise architecture lack analytical instruments for cyclic evaluations of business and system architectures in real business enterprise system environments. This impedes the broad use of enterprise architecture methodologies. Furthermore, the permanent evolution of systems desynchronizes quickly model representation and reality. Therefore we are introducing an approach for complementing the existing top-down approach for the creation of enterprise architecture with a bottom approach. Enterprise Architecture Analytics uses the architectural information contained in many infrastructures to provide architectural information. By applying Big Data technologies it is possible to exploit this information and to create architectural information. That means, Enterprise Architectures may be discovered, analyzed and optimized using analytics. The increased availability of architectural data also improves the possibilities to verify the compliance of Enterprise Architectures. Architectural decisions are linked to clustered architecture artifacts and categories according to a holistic EAM Reference Architecture with specific architecture metamodels. A special suited EAM Maturity Framework provides the base for systematic and analytics supported assessments of architecture capabilities.
Bootstrap circuits are mainly used for supplying a gate driver circuit to provide the gate overdrive voltage for a high-side NMOS transistor. The required charge has to be provided by a bootstrap capacitor which is often too large for integration if an acceptable voltage dip at the capacitor has to be guaranteed. Three options of an area efficient bootstrap circuit for a high side driver with an output stage of two NMOS transistors are proposed. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and connected when the gate driver turns on. A high voltage swing at the second capacitor leads to a high charge allocation. Both bootstrap capacitors require up to 70% less area compared to a conventional bootstrap circuit. This enables compact power management systems with fewer discrete components and smaller die size. A calculation guideline for optimum bootstrap capacitor sizing is given. The circuit was manufactured in a 180nm high-voltage BiCMOS technology as part of a high-voltage gate driver. Measurements confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit including two stacked 75.8pF and 18.9pF capacitors results in a voltage dip lower than 1V. This matches well with the theory of the calculation guideline.
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
SmartLife ecosystems are emerging as intelligent user-centered systems that will shape future trends in technology and communication. Biological metaphors of living adaptable ecosystems provide the logical foundation for self-optimizing and self-healing run-time environments for intelligent adaptable business services and related information systems with service-oriented enterprise architectures. The present research in progress work investigates mechanisms for adaptable enterprise architectures for the development of service-oriented ecosystems with integrated technologies like Semantic Technologies, Web Services, Cloud Computing and Big Data Management. With a large and diverse set of ecosystem services with different owners, our scenario of service-based SmartLife ecosystems can pose challenges in their development, and more importantly, for maintenance and software evolution. Our research explores the use of knowledge modeling using ontologies and flexible metamodels for adaptable enterprise architectures to support program comprehension for software engineers during maintenance and evolution tasks of service-based applications. Our previous reference enterprise architecture model ESARC -- Enterprise Services Architecture Reference Cube -- and the Open Group SOA Ontology was extended to support agile semantic analysis, program comprehension and software evolution for a SmartLife applications scenario. The Semantic Browser is a semantic search tool that was developed to provide knowledge-enhanced investigation capabilities for service-oriented applications and their architectures.
Modern web-based applications are often built as multi-tier architecture using persistence middleware. Middleware technology providers recommend the use of Optimistic Concurrency Control (OCC) mechanism to avoid the risk of blocked resources. However, most vendors of relational database management systems implement only locking schemes for concurrency control. As consequence a kind of OCC has to be implemented at client or middleware side.
A simple Row Version Verification (RVV) mechanism has been proposed to implement an OCC at client side. For performance reasons the middleware uses buffers (cache) of its own to avoid network traffic and possible disk I/O. This caching however complicates the use of RVV because the data in the middleware cache may be stale (outdated). We investigate various data access technologies, including the new Java Persistence API (JPA) and Microsoft’s LINQ technologies for their ability to use the RVV programming discipline.
The use of persistence middleware that tries to relieve the programmer from the low level transaction programming turns out to even complicate the situation in some cases.Programmed examples show how to use SQL data access patterns to solve the problem.
Transaction processing is of growing importance for mobile computing. Booking tickets, flight reservation, banking, ePayment, and booking holiday arrangements are just a few examples for mobile transactions. Due to temporarily disconnected situations the synchronisation and consistent transaction processing are key issues. Serializability is a too strong criteria for correctness when the semantics of a transaction is known. We introduce a transaction model that allows higher concurrency for a certain class of transactions defined by its semantic. The transaction results are ”escrow serializable” and the synchronisation mechanism is non-blocking. Experimental implementation showed higher concurrency, transaction throughput, and less resources used than common locking or optimistic protocols.