Refine
Year of publication
Document Type
- Conference proceeding (222)
- Journal article (30)
Language
- English (252)
Is part of the Bibliography
- yes (252)
Institute
- Technik (141)
- Informatik (90)
- ESB Business School (19)
- Life Sciences (1)
- Texoversum (1)
Publisher
- IEEE (252) (remove)
Size and cost of a switched mode power supply can be reduced by increasing the switching frequency. The maximum switching frequency and the maximum input voltage range, respectively, is limited by the minimum propagated on-time pulse, which is mainly determined by the level shifter speed. At switching frequencies above 10 MHz, a voltage conversion with an input voltage range up to 50 V and output voltages below 5 V requires an on-time of a pulse width modulated signal of less than 5 ns. This cannot be achieved with conventional level shifters. This paper presents a level shifter circuit, which controls an NMOS power FET on a high-voltage domain up to 50 V. The level shifter was implemented as part of a DCDC converter in a 180 nm BiCMOS technology. Experimental results confirm a propagation delay of 5 ns and on-time pulses of less than 3 ns. An overlapping clamping structure with low parasitic capacitances in combination with a high-speed comparator makes the level shifter also very robust against large coupling currents during high-side transitions as fast as 20 V/ns, verified by measurements. Due to the high dv/dt, capacitive coupling currents can be two orders of magnitude larger than the actual signal current. Depending on the conversion ratio, the presented level shifter enables an increase of the switching frequency for multi-MHz converters towards 100 MHz. It supports high input voltages up to 50 V and it can be applied also to other high-speed applications.
Bootstrap circuits are mainly used for supplying a gate driver circuit to provide the gate overdrive voltage for a high-side NMOS transistor. The required charge has to be provided by a bootstrap capacitor which is often too large for integration if an acceptable voltage dip at the capacitor has to be guaranteed. Three options of an area efficient bootstrap circuit for a high side driver with an output stage of two NMOS transistors are proposed. The key idea is that the main bootstrap capacitor is supported by a second bootstrap capacitor, which is charged to a higher voltage and connected when the gate driver turns on. A high voltage swing at the second capacitor leads to a high charge allocation. Both bootstrap capacitors require up to 70% less area compared to a conventional bootstrap circuit. This enables compact power management systems with fewer discrete components and smaller die size. A calculation guideline for optimum bootstrap capacitor sizing is given. The circuit was manufactured in a 180nm high-voltage BiCMOS technology as part of a high-voltage gate driver. Measurements confirm the benefit of high-voltage charge storing. The fully integrated bootstrap circuit including two stacked 75.8pF and 18.9pF capacitors results in a voltage dip lower than 1V. This matches well with the theory of the calculation guideline.
While digital IC design is highly automated, analog circuits are still handcrafted in a time-consuming, manual fashion today. This paper introduces a novel Parameterized Circuit Description Scheme (PCDS) for the development of procedural analog schematic generators as parameterized circuits. Circuit designers themselves can use PCDS to create circuit automatisms which capture valuable expert knowledge, offer full topological flexibility, and enhance the re-use of well-established topologies. The generic PCDS concept has been successfully implemented and employed to create parameterized circuits for a broad range of use cases. The achieved results demonstrate the efficiency of our PCDS approach and the potential of parameterized circuits to increase automation in circuit design, also to benefit physical design by promoting the common schematic-driven-layout flow, and to enhance the applicability of circuit synthesis approaches.
This paper presents the design and simulation processes of an Equiangular Spiral Antenna for the extremely high frequencies between 65 GHz and 170 GHz. A new approach for the analysis of the antenna’s electrical parameters is described. This approach is based on formalism proposed by Rumsey to determine the EM field produced by an equiangular spiral antenna. Analytical expressions of the electrical parameters such as the gain or the directivity are then calculated using well sustained mathematical approximations. The comparison of obtained results with those from numerical integration methods shows a good agreement.
This paper presents a new broadband antenna for satellite communications. It describes the procedure involved in the design of a microstrip antenna array and its multi-level passive feed network that together yield circular polarization and the necessary gain to be used in an earth-satellite link. The designed antenna is notable for its large bandwidth, circular polarization, high gain and small dimensions.
Advanced power semiconductors such as DMOS transistors are key components of modern power electronic systems. Recent discrete and integrated DMOS technologies have very low area-specific on-state resistances so that devices with small sizes can be chosen. However, their power dissipation can sometimes be large, for example in fault conditions, causing the device temperature to rise significantly. This can lead to excessive temperatures, reduced lifetime, and possibly even thermal runaway and subsequent destruction. Therefore, it is required to ensure already in the design phase that the temperature always remains in an acceptable range. This paper will show how self-heating in DMOS transistors can be experimentally determined with high accuracy. Further, it will be discussed how numerical electrothermal simulations can be carried out efficiently, allowing the accurate assessment of self-heating within a few minutes. The presented approach has been successfully verified experimentally for device temperatures exceeding 500 ◦C up to the onset of thermal runaway.
Analysis and planning of Enterprise Architectures (EA) is a complex task for stakeholders. The change of one architecture element has impact on multiple other elements because of manifold relationships and interactions between them. The interactive cockpit approach presented in this paper supports stakeholders planning and analyzing EAs and to tackle the intrinsic complexity. This approach supplies a cockpit with multiple viewpoints to put relevant information side-by-side without losing the context combined with interaction functionality. In this paper, we develop such cockpit starting with relevant use cases, describing a potential design based on well-established foundations in EA modeling, and outline an exemplary usage scenario.
Model-guided Therapy and Surgical Workflow Systems are two interrelated research fields, which have been developed separately in the last years. To make full use of both technologies, it is necessary to integrate them and connect them to Hospital Information Systems. We propose a framework for integration of Model-guided Therapy in Hospital Information Systems based on the Electronic Medical Record, and a taskbased Workflow Management System, which is suitable for clinical end users. Two prototypes - one based on Business Process Modeling Language, one based on the serum-board - are presented. From the experience with these prototypes, we developed a novel personalized visualization system for Surgical Workflows and Model-guided Therapy. Key challenges for further development are automated situation detection and a common communication infrastructure.
In the luxury Fashion industry, consumers could be categorized into two groups: fashion leader and Fashion follower. Both groups of consumers purchase luxury fashion products aim at satisfying both their functional needs and social needs (i.e., social influence). Thus the demands of both consumer groups are related. In this paper, we construct a model to examine the effects of pricing and online retail service in luxury fashion firms with social influence. To maximize profit, we identify the optimal prices and online retail service when the luxury fashion firms provide the non-differentiated and differentiated online retail services, respectively. More insights are discussed.
The automotive industry faces three major challenges – shortage of fossil fuels, politics of global warming and rising competition from new markets. In order to remain competitive companies have to develop more efficient and alternative fuel vehicles that meet the individual requirements of the customers. Functional Integration combined with new Technologies and materials are the key to stable success in this industry. The sustaining upward trend to system innovations within the last ten years confirms this. The development of complex products like automobiles claim skills of various disciplines e.g. engineering, chemistry. Furthermore, these skills are spread all over the supply chain. Hence the only way to stay successful in the automotive industry is cooperation and collaborative innovation. Interdisciplinary and interorganizational development has high demands on cooperation models especially in the automotive industry. In this case study cooperation models are analyzed and evaluated according to their applicability to interdisciplinary, interorganizational development projects in the automotive industry. Following, the research campus ARENA2036 is analyzed. ARENA2036 is an interdisciplinary, interorganizational development project housing automobile manufacturers, suppliers, research establishments and university institutes. Finally, based on interviews with the partners and the precede analyses of cooperation models, suggestions for implementation are given to ARENA2036.